Vtech M1 Dueling Spinning Spirals Raceway Instruction Manual

: July 23, 2024
: vtech

Table of Contents

Vtech M1 Dueling Spinning Spirals Raceway
Product Information
Product Usage Instructions
INTRODUCTION
INCLUDED IN THE PACKAGE
INSTRUCTIONS
ASSEMBLY INSTRUCTIONS
PRODUCT FEATURES
ACTIVITIES Crash Car
ACTIVITIES Criss-cross Spiral Playset
MELODY LIST
SONG
CARE & MAINTENANCE
TROUBLESHOOTING
Supplier’s Declaration of Conformity
References
Read User Manual Online (PDF format)
Download This Manual (PDF format)

Vtech M1 Dueling Spinning Spirals Raceway

Product Information

Specifications:

Product Name: Dueling Spinning Spirals RacewayTM
Features: 2-in-1 Launcher, Cross tracks, Spinning flags, Rival Racer Crash Car
Components: See included items in the package list

Product Usage Instructions

Battery Removal And Installation – Race Car

Make sure the unit is turned OFF.
Find the battery cover located on the bottom of the Race Car, use a screwdriver to loosen the screw and then open the battery cover.
Remove old batteries by pulling up on one end of each battery.
Install 2 new AAA (AM-4/LR03) batteries following the diagram inside the battery box. (For best performance, alkaline batteries or fully charged Ni-MH rechargeable batteries are recommended).
Replace the battery cover and tighten the screw to secure.

Assembly Instructions
Assembling the Podium and Pillars:

Insert the major pillars into the slots on the tower base M1. A clicking sound will confirm they are firmly connected.
Insert screws into the holes on the bottom of base M1 and tighten them.
Insert three double brackets M to connect the pillars. Ensure a clicking sound confirms they are firmly connected.

Attaching Tracks on the Ground Floor :

Attach track A to the Base M1 by inserting it into the slot of the base bracket L1. Confirm connection with a clicking sound.
Attach track B to the Base M1 by inserting it into the slot of base bracket R1. Confirm connection with a clicking sound.

Attaching Tracks on the Second Floor:

Insert cross track M2 between the pillars and into the slots of the 1st bracket M. Confirm connection with a clicking sound.

FAQ (Frequently Asked Questions)

Q: What type of batteries should I use for the Race Car?
A: It is recommended to use 2 new AAA (AM-4/LR03) batteries. For best performance, alkaline batteries or fully charged Ni-MH rechargeable batteries are suggested.
Q: How do I remove packaging locks from the product?
A: Turn the packaging locks anticlockwise several times, pull them out, and discard.

Dueling Spinning Spirals Raceway™

INTRODUCTION

Thank you for purchasing the VTech® Go! Go! Smart Wheels-Dueling Spinning Spirals Raceway™. Little ones will love exploring the VTech® Go! Go! Smart Wheels – Dueling Spinning Spirals Raceway™. Race to the finish line with the SmartPoint® Crash Car, and Rival Racer. It’s time to have a race!

INCLUDED IN THE PACKAGE

One base M1(You can find piece numbers engraved on the bottom) with one SmartPoint™ Winner’s Podium

Two Cross tracks M2, M3

Six slide tracks A,B,C,D,E,F

Two base brackets L1,R1

Two Left tower brackets L2

Two Right tower brackets R2

Sticker Sheet
Quick Start Guide
WARNING
- All packing materials such as tape, plastic sheets, packaging locks, removable tags, cable ties, cords and packaging screws are not part of this toy, and should be discarded for your child’s safety.
NOTE
- Please save this manual as it contains important information.

CAUTION

This package contains small screws. Adult assembly required.
For your child’s safety, do not let your child play with the toy until it is fully assembled.
If there are no locks inside the package, disregard this message.
Removing the Packaging Locks:
1. Turn the packaging locks anticlockwise several times.
2. Pull out the packaging locks and discard.

CAUTION : This package contains small screws. Adult assembly required. For your child’s safety, do not let your child play with the toy until it is fully assembled.

INSTRUCTIONS

Battery Removal And Installation – Race Car

Make sure the unit is turned OFF.
Find the battery cover located on the bottom of the Race Car, use a screwdriver to loosen the screw and then open the battery cover.
Remove old batteries by pulling up on one end of each battery.
Install 2 new AAA (AM-4/LR03) batteries following the diagram inside the battery box. (For best performance, alkaline batteries or fully charged Ni-MH rechargeable batteries are recommended).
Replace the battery cover and tighten the screw to secure.

WARNING : Adult assembly required for battery installation. Keep batteries out of reach of children.

MPORTANT: BATTERY INFORMATION

Insert batteries with the correct polarity (+ and -).
Do not mix old and new batteries.
Do not mix alkaline, standard (carbon-zinc) or rechargeable batteries.
Only batteries of the same or equivalent type as recommended are to be used.
Do not short-circuit the supply terminals.
Remove batteries during long periods of non-use.
Remove exhausted batteries from the toy.
Dispose of batteries safely. Do not dispose of batteries in fire.

RECHARGEABLE BATTERIES

Remove rechargeable batteries (if removable) from the toy before charging.
Rechargeable batteries are only to be charged under adult supervision.
Do not charge non-rechargeable batteries.

LABEL APPLICATION
Please adhere the labels to the playset securely as indicated on the following page:

ASSEMBLY INSTRUCTIONS

With the Go! Go! Smart Wheels® – Dueling Spinning Spirals Raceway™, safety comes first. To ensure your child’s safety, adult assembly is required.

Assemble and attach the Base M1 with the SmartPoint™ Winner’s podium and two major pillars following the steps below:
Insert the major pillars into the slots on the tower base M1.A clicking sound will confirm they are firmly connected.
- Insert 4 screws into the holes on the bottom of base M1, and tighten them.
- Insert three double brackets M to connect the pillars. Starting at the back of the pillars, insert each bracket M into the slot (shown below). A clicking sound will confirm they are firmly connected.
- Use the same method to insert the base brackets L1 & R1, two left tower brackets L2, and two right tower brackets R2. A clicking sound will confirm they are firmly connected
Assemble and attach the tracks on the ground floor following the steps below:
Attach track A to the Base M1: Insert track A into the slot of the base bracket L1, then connect the track with the base. A clicking sound will confirm they are firmly connected.
- Attach track B to the Base M1: Insert the track B into the slot of base bracket R1, then connect the track with the base. A clicking sound to confirm they are firmly connected.
Assemble and attach the tracks on the second floor following the steps below:
Insert cross track M2 (screw-hole on the M2 face forward) into the 1st bracket M: Pass the cross track M2 between the pillars and insert it into the slots of the 1st bracket M. A clicking sound will confirm they are firmly connected.
- Connect track A and track B with cross track M2.
Assemble and attach the tracks on the third floor following the steps below:
Insert the cross track M3 into the 2nd bracket M: Pass the cross track M2 between the pillars and insert it into the slots of the 2nd bracket M. A clicking sound will confirm they are firmly connected.
- Connect the track C with cross track M2&M3: Connect track C to Left tower bracket L2. Then connect track C to the left rear of M2 and the left front of M3. A clicking sound will confirm they are firmly connected.
- Connect the track D with cross track M2&M3: Connect track D to Right tower bracket R2. Then connect track D to the right rear of M2 and the right front of M3. A clicking sound will confirm they are firmly connected.
Assemble and attach the tracks on the next level following the steps below:
Connect the track E with cross track M3: Connect track E to Left tower bracket L2. Then connect track E to the left rear of M3 and the left front of M. A clicking sound will confirm they are firmly connected.
- Connect the track F with cross track M3: Connect track F to Left tower bracket R2. Then connect track E to the left rear of M3 and the left front of M. A clicking sound will confirm they are firmly connected.
- Connect the track E & track F. A clicking sound will confirm they are firmly connected.
Assemble and attach the small & big brackets with the tower base M1 following the steps below:
After above steps, flip the unit to show the bottom of the base and locate 2 slots besides the screws.
- Insert the small bracket into the left slot of the base.
- Insert the small bracket into the right slot of the base.
Assemble and attach the Finish line to tower base M1 following the steps below:
- Before inserting the Finish line, make sure the label side is facing forward.
- Connect and insert the top of the door into the slots of M2.
- Connect and insert the bottom of the door into the slots of M1. Then tighten the screw at M2 to secure.
Assemble and attach the launcher following the steps below:
- Insert the launcher handle into the slots of the 2-in-1 launcher.
- Insert the launcher on the top of the raceway. A clicking sound to confirm they are firmly connected.
Assemble and attach the flags following the steps below:
- From back to front, insert the tower top into the slot on the top of the left pillar. Push the tower flag into the slot on the top of the right pillar.
- Assemble the spinning flags.
- Once you’ve completed the above steps, you are ready to play! You can also connect the construction tower to other Go! Go! Smart Wheels® track sets (each sold separately).

PRODUCT FEATURES

Crash Car

On/Off Switch
- To turn the unit On, slide the On/Off Switch to the On ( ) position. To turn the unit Off, slide the On/Off Switch to the Off ( ) position
Automatic Shut-Off
- To preserve battery life, the SmartPoint® Crash Car will automatically power-down after approximately 60 seconds without input . The unit can be turned on again by pressing the Light Up Button or triggering a SmartPoint® location.
- Note: This product is in Try-Me mode in the packaging. After opening the package, turn the SmartPoint® Crash Car off and on again to proceed with normal play. If the unit powers down while playing, we suggest changing the batteries.

ACTIVITIES Crash Car

Press the Light-up Button to hear fun phrases, songs, sounds and melodies. While a melody is playing, continue pushing the SmartPoint® Crash Car to add fun sounds on top of the melody. The windshield light will flash with sounds.
Push the SmartPoint® Crash Car to hear fun sounds and phrases. The windshield light will flash with sounds.
Place the SmartPoint® Crash Car on one of the playset’s three SmartPoint® locations to see the vehicle’s lights flash and to hear fun sounds, short tunes and phrases.
The SmartPoint® Crash Car even interacts with other Go! Go! Smart Wheels® playsets (other playsets sold separately).

ACTIVITIES Criss-cross Spiral Playset

Place the SmartPoint® Crash Car or any SmartPoint® vehicle (each sold separately) on any of the three SmartPoint® locations to trigger fun sounds, songs or phrases.
Put the SmartPoint® Crash Car and Rival Racer on the SmartPoint® Launcher 1 & Launcher 2, then pull the handle to launch and race.
Put the SmartPoint® Crash Car on the SmartPoint® Winner’s Podium to hear some fun phrases and responses.

MELODY LIST

Yankee Doodle
A-Tisket A-Tasket
Do You Know the Muffin Man
Skip to My Lou
Three Little Kittens
Bicycle Built for Two

SONG

Song 1
- Got to go fast, to be first to hit the finish line. I’m first! Oh yes, I’m first because I’m fast!Yes, I’m fast! Yes, I’m super, duper speedy fast. I’m fast!
Song 2
- Slow, slow, slow it down, gently tap your brakes.
- Take your time, to unwind, when you need a break
Song 3
- Go! Go! Smart Wheels!
- I’m a Go! Go! Smart Wheels Race Car.
- Cheer and clap for me(Go! Go!)
- We will win the championship.
- Let’s Go! Go! and see! (Go! Go!)
Song 4
- And when I go fast, I go super fast, and when I’m slow, I calm down.

CARE & MAINTENANCE

Keep the unit clean by wiping it with a slightly damp cloth.
Keep the unit out of direct sunlight and away from any direct heat sources.
Remove the batteries if the unit will not be in use for an extended period of time.
Do not drop the unit on a hard surface and do not expose the unit to moisture or water.

TROUBLESHOOTING

If for some reason the unit stops working or malfunctions, please follow these steps:

Turn the unit Off.
Interrupt the power supply by removing the batteries.
Let the unit stand for a few minutes, then replace the batteries.
Turn the unit On. The unit should now be ready to play again.
If the unit still does not work, install a new set of batteries.

CAUTION
Changes or modifications not expressly approved by the party responsible for compliance could void the user’s authority to operate the equipment.

NOTE
This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to Part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation. This equipment generates, uses and can radiate radio frequency energy and, if not installed and used in accordance with the instructions, may cause harmful interference to radio communications. However, there is no guarantee that interference will not occur in a particular installation.

If this equipment does cause harmful interference to radio or television reception, which can be determined by turning the equipment off and on, the user is encouraged to try to correct the interference by one or more of the following measures:
- Reorient or relocate the receiving antenna
- Increase the separation between the equipment and receiver
- Connect the equipment into an outlet on a circuit different from that to which the receiver is connected
- Consult the dealer or an experienced radio/TV technician for help

IMPORTANT NOTE:
If the problem persists, please call our Consumer Services Department at 1-800-521-2010 in the U.S. or 1-877-352-8697 in Canada, or by going to our website at vtechkids.com and filling out our Contact Us form located under the Customer Support link. Creating and developing VTech products is accompanied by a responsibility that we take very seriously. We make every effort to ensure the accuracy of the information, which forms the value of our products. However, errors sometimes can occur. It is important for you to know that we stand behind our products and encourage you to contact us with any problems and/or suggestions you might have. A service representative will be happy to help you.

Supplier’s Declaration of Conformity

47 CFR & 2.1077 Compliance Information

Trade Name: VTech®
Model: 5702
Product Name: Dueling Spinning Spirals Raceway TM
Responsible Party: VTech Electronics North America, L.L.C
Address: 1156 W. Shure Drive, Suite 200 Arlinaton Hoinhte || 60004
Website. vtechkids.com

THIS DEVICE COMPLIES WITH PART 15 OF THE FCC RULES OPERATION IS SUBJECT TO THE FOLLOWING TWO CONDITIONS

THIS DEVICE MAY NOT CAUSE HARMFUL INTERFERENCE, AND
THIS DEVICE MUST ACCEPT ANY INTERFERENCE RECEIVED INCLUDING INTERFERENCE THAT MAY CAUSE UNDESIRED OPERATION. CAN ICES-003(B)/NMB-003(B)

Visit our website for more information about our products, downloads, resources and more.