FLAMERiTE FiRES E-FX 52 Inch 3-Sided 2-Sided Built In Electric Fireplace Instruction Manual
- July 23, 2024
- FLAMERITE FIRES
Table of Contents
E-FX 52 Inch 3-Sided 2-Sided Built In Electric Fireplace
“`html
Specifications:
Trade Name: E-FX
Ratings: 220-240 Vac, 50Hz Class I, Electric
Fire (fan heater) (5120 BTU)
Manufactured By: Flamerite Fires LTD.
Greenhough Road, Lichfield. Staffs. WS13 7AU. United Kingdom.
Requirements:
-
BS-EN 60335-2-30:2009 + A11:2012
-
BS-EN 60335-1:2012 + A11:2014 + A13:2017 + A1:2019 + A14:2019 +
A2:2019 -
BS-EN 55014-1:2017 BS-EN IEC 6300 :2018
-
BS-EN 55014-2:2015
-
BS-EN 301 489-1
-
BS-EN61000-3-2:2014
-
BS-EN 300 489-3
-
BS-EN 61000-3-3:2013
-
BS-EN 300 220
-
BS-EN 50564:2011 BS-EN 60675:1995+A11:2019
Product Usage Instructions:
Important Safety Instructions:
– This product is intended for use by individuals aged 8 years
and above.
– Always supervise children, invalids, or vulnerable individuals
using the heater.
– Keep flammable materials away from the heater to prevent fire
hazards.
Installation Precautions:
– Do not cover the heater or obstruct airflow.
– Ensure the heater is placed at least 3 feet (0.9m) away from
furniture, bedding, and curtains.
Servicing Guidelines:
– If the heater malfunctions, disconnect power and have it
inspected by a reputable electrician.
– Children under 8 years should only operate the heater under
supervision.
FAQ:
Q: Can children operate the heater?
A: Children under 8 years should only switch the heater on/off
if supervised by an adult.
Q: What should I do if the heater malfunctions?
A: Disconnect power, remove the cause of overheating, allow it
to cool, and then switch it back on. If issues persist, contact a
professional electrician.
“`
INSTALL ATION, PRECAUTIONS & SERVICING
JULY 2024
IMPORTANT
· Please bear in mind the weight of the fire before removing from the
packaging and installation.
· Consider if help is required.
· Carefully remove the fire from the packaging, making sure that the power
cable and heater have not been damaged during transport.
· DO NOT operate the fire if damaged.
· The accessories are found in a box that is packed at the side of the fire.
· Always read this manual first before attempting to install or use and keep
in a safe place.
· Your fire is guaranteed for three years from the date of purchase.
IMPORTANT
SAVE THESE INSTRUCTIONS!
2
ELECTRIC FIRES MADE IN EUROPE
CONTENTS
Important Instructions……………………………………………………………………………………………………………………………… 4 UKCA & CE Declarations ………………………………………………………………………………………………………………………….. 7 ETL Declarations……………………………………………………………………………………………………………………………………….. 8 Technical Specifications …………………………………………………………………………………………………………………………… 9 Required Tools………………………………………………………………………………………………………………………………………… 10 What’s In The Box……………………………………………………………………………………………………………………………………. 11 Before You Start ……………………………………………………………………………………………………………………………………… 12 Blanking Plate Installation………………………………………………………………………………………………………………………. 13 Flat Wall Installation………………………………………………………………………………………………………………………………… 15 Hard-wire Installation……………………………………………………………………………………………………………………………… 20 Stud Wall Installation………………………………………………………………………………………………………………………………. 24 Rear Screen Options………………………………………………………………………………………………………………………………. 31 Front Glass Installation…………………………………………………………………………………………………………………………… 33 Informational Requirements …………………………………………………………………………………………………………………. 36 Maintenance……………………………………………………………………………………………………………………………………………. 37 Trouble Shooting…………………………………………………………………………………………………………………………………….. 38 Wiring Diagram ……………………………………………………………………………………………………………………………………….. 40 Parts List…………………………………………………………………………………………………………………………………………………… 41 Exploded Diagram ………………………………………………………………………………………………………………………………….. 42 Cleaning & Maintenance………………………………………………………………………………………………………………………… 43 Warranty…………………………………………………………………………………………………………………………………………………… 43
ELECTRIC FIRES MADE IN EUROPE
3
IMPORTANT INSTRUCTIONS
IMPORTANT
REGISTRATION NO WEE/DH1656ZW · In accordance with European Directive 2012/19/
EU,
waste electrical and electronic equipment (WEEE) must not be disposed of with
household waste. · Please recycle responsibly.
DETAILS
· Read all the instructions before installing or · The use of an extension lead is
using this heater.
NOT recommended.
· WARNING: In order to avoid overheating, · This appliance can be used by children
do not cover the heater.
aged from 8 years and above and
· For indoor use only.
persons with reduced physical, sensory or mental capabilities or lack of experience
· DO NOT use the fire in the vicinity of a bath, shower or swimming pool.
and knowledge if they have been given supervision or instruction concerning use of the appliance in a safe way and understand
· NEVER use the fire to dry laundry.
the hazards involved.
· The heater must not be located immediately below a socket outlet.
· Children shall NOT play with the appliance.
4
ELECTRIC FIRES MADE IN EUROPE
IMPORTANT INSTRUCTIONS
· Cleaning and user maintenance shall NOT · Extreme caution is necessary when any
be made by children without supervision.
heater is used by or near children or
· Children of less than 3 years should be kept away unless continuously supervised.
invalids and whenever the heater is left operating and unattended.
· Do not operate any heater after it
· Children aged from 3 years and less
malfunctions. Disconnect power at service
than 8 years shall only switch on/off the
panel and have heater inspected by a
appliance provided that it has been placed
reputable electrician before reusing.
or installed in its intended normal operating
position and they have been given supervision · Do not use outdoors.
or instruction concerning use of the appliance in a safe way and understand the hazards involved.
· To disconnect heater, turn controls to off and turn off power to heater circuit at main disconnect panel.
· Children aged from 3 years and less than 8 years shall not plug in, regulate and clean the appliance or perform user maintenance.
· Do not insert or allow foreign objects to enter any ventilation or exhaust opening as this may cause an electric shock or fire, or damage to the heater.
· Some parts of this product can become very hot and cause burns. Particular attention must be given where children
· To prevent a possible fire, do not block air intakes or exhaust in any manner.
and vulnerable people are present.
· A heater has hot and arcing or sparking
· The heater is hot when in use. To avoid burns, do not let bare skin touch hot surfaces. Keep combustible materials,
parts inside. Do not use it in areas where gasoline, paint, or flammable vapour or liquids are used or stored.
such as furniture, pillows, bedding, paper, clothes, etc. and curtains at least 3 feet (0.9m) from the front of the heater and keep them away from the sides and rear (sides and rear restrictions apply to location
· Use this heater only as directed in this manual. Any other use not recommended by the manufacture may cause fire, electric shock, or injury to persons.
dedicated heaters only).
ELECTRIC FIRES MADE IN EUROPE
5
IMPORTANT INSTRUCTIONS
CAUTION
CAUTION RISK OF ELECTRIC SHOCK
DO NOT OPEN NO USER-SERVICEABLE PARTS INSIDE
· The heater must be properly installed before it is used.
· Caution should be applied to ensure that children DO NOT play with the fuel
effects.
· As with any electrical appliance whilst the instructions aim to cover as
many eventualities as possible, caution and common sense should be applied
when operating your appliance, particularly in the vicinity of small children.
· CAUTION: The heater is fitted with an automatic cut out to prevent any
damage due to overheating. The element will continually and automatically cut
out if
the airflow is obstructed. Never cover the air outlets. To reset, switch the
fire off, disconnect from the main supply, remove the cause of the
overheating. Allow to cool for a suitable period then switch the fire back on.
· CAUTION: In order to avoid a hazard due to inadvertent resetting of the
thermal cut out, the appliance must not be supplied through an external
switching device, such as a timer, or connected to a circuit regularly
switched on and off by a utility.
· 2.4 GHz network required.
6
ELECTRIC FIRES MADE IN EUROPE
UKCA & CE DECLARATIONS
TRADE NAME E-FX
RATINGS
PRODUCT TYPE
MANUFACTURED BY
220-240 Vac, 50Hz Class I
Electric Fire (fan heater) (5120 BTU)
Flamerite Fires LTD. Greenhough Road, Lichfield. Staffs. WS13 7AU. United Kingdom.
REQUIREMENTS:
BS-EN 60335-2-30:2009 + A11:2012
BS-EN 60335-1:2012 + A11:2014 + A13:2017 + A1:2019 + A14:2019 + A2:2019
BS-EN 55014-1:2017 BS-EN IEC 6300 :2018
BS-EN 55014-2:2015
BS-EN 301 489-1
BS-EN61000-3-2:2014
BS-EN 300 489-3
BS-EN 61000-3-3:2013
BS-EN 300 220
BS-EN 50564:2011 BS-EN 60675:1995+A11:2019
TRADE NAME E-FX
RATINGS
PRODUCT TYPE
MANUFACTURED BY
220-240 Vac, 50Hz Class I
Electric Fire (fan heater) (5120 BTU)
REQUIREMENTS: EN 60335-2-30:2009 + A11:2012
Flamerite Fires LTD. Greenhough Road, Lichfield. Staffs. WS13 7AU. United Kingdom.
EN 60335-1:2012 + A11:2014 + A13:2017 + A1:2019 + A14:2019 + A2:2019
EN 55014-1:2017
EN IEC 6300 :2018
EN 55014-2:2015
EN 301 489-1
EN61000-3-2:2014
EN 300 489-3
EN 61000-3-3:2013
EN 300 220
EN 50564:2011 EN 60675:1995+A11:2019
ELECTRIC FIRES MADE IN EUROPE
7
ETL DECLARATIONS
TRADE NAME E-FX
CERTIFICATE NUMBER FFID
RATINGS
PRODUCT TYPE
MANUFACTURED BY
120 Vac, 60Hz Class I
Electric Fire (fan heater) (5120 BTU)
Flamerite Fires LTD. Greenhough Road, Lichfield. Staffs. WS13 7AU. United Kingdom.
REQUIREMENTS:
UL 2021 & CAN/CSA E60335-2-30
5028692
2AC7Z-ESP32WVROOM3
DETAILS
· A 120V 60Hz 15A or 240V 50Hz 13A supply is required.
· Maximum Power Consumption: 1500 Watts (BTU: 5120)
· A 1.8 metre lead / 6 foot lead is supplied with this appliance.
WARNING
DO NOT twist, force or squeeze the fire during the installation process.
· There must be enough clearance for the fire to comfortably fit inside or
against a wall.
· DO NOT squeeze into an opening as this may deform the case and stop the
glass from moving correctly.
· The fire must be well supported in or on any structure. Never secure to just
plaster board alone.
· A wall support or lintel should be fitted at the required height to ensure
the appliance does not support the weight of the finished wall or chimney
breast.
8
ELECTRIC FIRES MADE IN EUROPE
TECHNICAL SPECIFICATIONS
E B
A
D
C F
I G
H
E-FX 1000 – 40″
A
574mm / 22 5/8 ”
B
113mm / 4 7/16 ”
C
110mm / 4 5/16 ”
D
355mm / 14 ”
E
285mm / 11 1/4 ”
F
1005mm / 39 9/16 ”
G
206mm / 8 1/8 ”
H
1042mm / 41 ”
I
305mm / 12 ”
KG
50kg / 110 lbs
E-FX MODEL
E-FX 1300 – 52″
E-FX 1500 – 59″
574mm / 22 5/8 ”
574mm / 22 5/8 ”
113mm / 4 7/16 ”
113mm / 4 7/16 ”
110mm / 4 5/16 ”
110mm / 4 5/16 ”
355mm / 14 ”
355mm / 14 ”
285mm / 11 1/4 ”
285mm / 11 1/4 ”
1305mm / 51 3/8″
1505mm / 59 1/4″
206mm / 8 1/8 ”
206mm / 8 1/8 ”
1342mm / 52 13/16 ”
1542mm / 60 11/16 ”
305mm / 12 ”
305mm / 12 ”
60kg / 132 lbs
66kg /145 lbs
E-FX 1800 – 70″ 574mm / 22 5/8 ” 113mm / 4 7/16 ” 110mm / 4 5/16 ”
355mm / 14 ” 285mm / 11 1/4 ” 1805mm / 71 1/6 ” 206mm / 8 1/8 ” 1842mm / 72
1/2 ”
305mm / 12 ” 76kg / 167 lbs
DIMENSIONS & WEIGHT
ELECTRIC FIRES MADE IN EUROPE
9
REQUIRED TOOLS
HEX KEY
HAMMER & SCREWDRIVER
DRILL & DRILL BITS
TAPE MEASURE
PENCIL
SPIRIT LEVEL
10
ELECTRIC FIRES MADE IN EUROPE
WHAT’S IN THE BOX…
01
02
03
E-FX FIRE 04
LOG SET 05
BLANKING PLATES
06
FRONT GLASS 07
ACCESSORY & HARDWIRE PACK
DECORATIVE RAILS
08
09
INSTRUCTIONS
POWER LEAD
10
11
REMOTE & BATTERIES
GLASS HANDLE
FIXING PACK
ELECTRIC FIRES MADE IN EUROPE
11
BEFORE YOU START…
PLUG SOCKETS
All fires must have an accessible plug. Do not fit a fire above a socket.
Building regulations require the socket to be located at the side of the unit.
It is preferable to fit the fire to a 120 VOLT or 240 VOLT switched grounded
outlet for safety. This ensures it has it’s own supply and will not overload
current installations.
IMPORTANT
Please speak with a qualified expert before undertaking any work, and if
required, ask them to carry out the installation for you.
INCORRECT INSTALL
WALL FASTENERS
If fixing the fire to a wall, please ensure suitable fasteners are used for
the material the fire is being fixed to.
Often the wall is not completely flat and the floor uneven. When hanging the
fire be sure to take this into account to ensure a good solid fit that
supports the fire safely.
Your retailer may offer a installation service, or alternatively you can find
a builder to fit the fire for you.
CORRECT INSTALL
12
ELECTRIC FIRES MADE IN EUROPE
BLANKING PLATE INSTALLATION
SIDE PANEL INSTALLATION
If you have purchased a 1 or 2 sided E-FX Fire, you will need to install the
blanking plates BEFORE fitting the fire or installing into a chimney breast.
If fitting as a 1 or 2 sided corner fire, blanking panels will need to be
fitted. Each blanking panel consists of two parts, fitted directly over the
side glass. If you need to fit the blanking panel(s) follow the instructions
and images below. The blanking plates come preassembled with a label showing
which direction to fit them.
TIP
Save these!
TIP
Do not over tighten the screws as this will prevent the side glass from
moving.
01
Remove the screws from the blanking plates.
02
Fix into position by using the same four black screws provided, two on the top
and bottom but make sure the inner panel and the glass have free movement to
slide forwards and backwards. There are slots in the case to allow for any
tolerance during fitting.
ELECTRIC FIRES MADE IN EUROPE
13
BLANKING PLATE INSTALLATION
03
Once the blanking plate is screwed in test that the side glass can still move
freely. Finally, pull the inner part of the blanking plate forward so it is
flush with the side glass inside the fire.
14
ELECTRIC FIRES MADE IN EUROPE
FLAT WALL INSTALLATION
FITTING YOUR E-FX FIRE ONTO A WALL OR INTO A STRUCTURE…
If purchased as a fire only or as a standard wall mount suite, the height at
which you may wish to fix the fire in, or on the wall, is up to you. Be sure
to take account of local building regulations, and if not sure, always consult
a professional. When purchased as part of a E-FX Media Wall, refer to those
instructions. If purchased with a Suite & Plinth or Contemporary legs, the
height you will need to fit the top of the lower fire bracket to the floor is
in the table on the next page. Make sure you allow tolerance for any carpets
or deviation in the floor or wall level. All floor standing suites have
levelling feet that should be used to level the fire in the suite before final
fitting. These can be used to allow for any tolerance created by the carpet.
01
The lower bracket will have to be removed to begin the process. Save the
screws and washers for later.
TIP
Save these!
ELECTRIC FIRES MADE IN EUROPE
15
FLAT WALL INSTALLATION
PRODUCT
E-FX 1000 – 40″ E-FX 1300 – 52″ E-FX 1500 – 59″ E-FX 1800 – 70″
02
BOTTOM RAIL FIXING HEIGHT TABLE
FLOATING SUITE
200mm / 7 7/8″ Minimum 200mm / 7 7/8″ Minimum 200mm / 7 7/8″ Minimum 200mm / 7
7/8″ Minimum
SUITE WITH PLINTH
265mm / 9 1/16″ 265mm / 9 1/16″
N/A N/A
03
SUITE WITH CONTEMPORARY LEGS
230mm / 10 7/16″ 230mm / 10 7/16″
N/A N/A
Using a tape measure and level, mark the required height on the wall using the dimensions provided in the table above. The height is measured from the top of the bracket to the floor, as shown below. Mark where the center of the rail is.
Drill the holes with a 10mm (3/8″) drill bit and fit the wall plugs. Using the
screws, secure the bracket to the wall.
TIP
Mark a center line up the wall so you can align the top bracket.
FIXING 60mm / 2 3/8″ Wall Screws
10mm / 3/8″ Wall Plugs M6 Screws M6 Washers
1000 – 40″ 4 4 2 2
BOTTOM RAIL FIXING TABLE 1300 – 52″ 4 4 2 2
1500 – 59″ 4 4 2 2
1800 – 70″ 4 4 2 2
16
ELECTRIC FIRES MADE IN EUROPE
FLAT WALL INSTALLATION
FIXING 60mm / 2 3/8″ Wall Screws
10mm / 3/8″ Wall Plugs 13mm / 1/2″ Screws
1000 – 40″ 4 4 2
TOP RAIL FIXING TABLE 1300 – 52″ 4 4 2
1500 – 59″ 4 4 2
1800 – 70″ 4 4 2
04
Remove the top rail using a screwdriver and put the screws to one side. You
will need them later. Using a measuring tape measure from the TOP of the
BOTTOM BRACKET, to the BOTTOM of the TOP BRACKET, as shown below, aligning the
centerline with the cut-out in the center of the top bracket.
528MM – 530MM 20 13/16″ – 20 7/8″
05
Drill the holes with a 10mm (3/8″) drill bit and fit the wall plugs. Using the
screws secure the bracket to the wall.
ELECTRIC FIRES MADE IN EUROPE
17
FLAT WALL INSTALLATION
06
Next, using help if required lift the fire onto the bottom bracket and push
firmly against both brackets. Use a drill or screwdriver to fix the fire to
the top rail using the same screws that came with the bracket.
FLAT WALL INSTALLATION
08
When using the power lead check the underside of the fire for a clip. This is
provided to secure the cable in place as a safety precaution. Unscrew this
clip and place it around the cord before plugging the fire in securely. When
you have plugged the fire in, screw this clip back in place, ensuring
everything is secure, with NO excess strain on the cable.
07
Using the screws and washers removed from the bottom rail, screw the bracket
to the fire to ensure it is fully secured.
18
ELECTRIC FIRES MADE IN EUROPE
09
This heater is for use on 120 volts or 240 volts (depending on your region).
The cord has a plug as shown in Figure A. An adapter is available for
connecting three-blade grounding type plugs in two slot receptacles. The
grounding lug extending from the adapter must be connected to a permanent
ground such as a properly grounded outlet box. The adapter should not be used
if a three-slot grounded receptacle is available.
FIGURE A
GROUNDING PIN
ADAPTER GROUNDING SCREW
COVER FOR GROUNDED OUTLET BOX
ELECTRIC FIRES MADE IN EUROPE
19
STUD WALL INSTALLATION
PRE-INSTALLATION NOTES
If you have purchased a 1 or 2 sided E-FX Fire, you will need to install the
blanking plates BEFORE fitting the fire or installing into a structure. If
fitting as a 1 or 2 sided corner fire, blanking panels will need to be fitted.
Each blanking panel consists of two parts, fitted directly over the side
glass. If you need to fit the blanking panel(s) follow the instructions on
page 13 The blanking plates come pre-assembled with a label showing which
direction to fit them. Use the tables to build your structure. You must
install a header to make sure that the appliance does not support the weight
of the finished wall. This is critical to smooth fitting and operation of the
fire. The fire should be placed on a stable, level surface in a clean, dust-
free area. If installing the product into an open chimney or flue, make sure
the chimney or flue is sealed off to prevent drafts and falling debris that
could affect the product’s airflow. The power switch can not be hidden. It
must have an easily accessible switch. We recommend fitting the wall around
the fire to allow for any manufacturing tolerances. Any protruding headers
must be made of a non combusible material.
BEFORE FINISHING THE WALL MAKE SURE TO TEST THE APPLIANCE IS FULLY WORKING
20
ELECTRIC FIRES MADE IN EUROPE
STUD WALL INSTALLATION
1-SIDED
HEADER
H
D W
DIMENSION Height (H) Width (W) Depth (D)
1 SIDED MINIMUM REQUIRED DIMENSIONS
1000 – 40″
1300 – 52″
1500 – 59″
575mm / 22 5/8″ 1050mm / 41 5/16″ 295mm / 11 5/8″
575mm / 22 5/8″ 1350mm / 53 1/8″ 295mm / 11 5/8″
575mm / 22 5/8″ 1550mm / 61″ 295mm / 11 5/8″
1800 – 70″ 575mm / 22 5/8″ 1850mm / 72 13/16″ 295mm / 11 5/8″
ELECTRIC FIRES MADE IN EUROPE
21
STUD WALL INSTALLATION
2-SIDED
STUD WALL INSTALLATION
3-SIDED
HEADER
H
W D
DIMENSION Height (H) Width (W) Depth (D)
2 SIDED MINIMUM REQUIRED DIMENSIONS
1000 – 40″
1300 – 52″
1500 – 59″
575mm / 22 5/8″ 1030mm / 40 9/16″ 295mm / 11 5/8″
575mm / 22 5/8″ 1330mm / 52 3/8″ 295mm / 11 5/8″
575mm / 22 5/8″ 1530mm / 60 1/4″ 295mm / 11 5/8″
1800 – 70″ 575mm / 22 5/8″ 1830mm / 72 1/16″ 295mm / 11 5/8″
22
ELECTRIC FIRES MADE IN EUROPE
HEADER
H
W D
DIMENSION Height (H) Width (W) Depth (D)
3 SIDED MINIMUM REQUIRED DIMENSIONS
1000 – 40″
1300 – 52″
1500 – 59″
575mm / 22 5/8″ 1010mm / 39 3/4″ 295mm / 11 5/8″
575mm / 22 5/8″ 1310mm / 51 9/16″ 295mm / 11 5/8″
575mm / 22 5/8″ 1510mm / 59 7/16″ 295mm / 11 5/8″
1800 – 70″ 575mm / 22 5/8″ 1810mm / 71 1/4″ 295mm / 11 5/8″
ELECTRIC FIRES MADE IN EUROPE
23
STUD WALL INSTALLATION
01
Now the wall is built, remove the top bracket from the fireplace.
02
Slide the fire into the opening and position it where required.
03
Final turn the top bracket upside down, and fix it to the fire and the wall as
shown. You can then finish the wall with your chosen construction. Remeber any
protruding headers must be non combistible.
24
ELECTRIC FIRES MADE IN EUROPE
HARD-WIRE INSTALLATION
WARNING!
Before any wiring work is undertaken, make sure the power for the socket has
been turned off at the fuse box and check that the power is off. Make sure the
unit is disconnected from any power source. Ensure proper safety precautions
are taken before attempting any work.
This should only be carried out by a competent person who has the knowledge to
complete the task. If you have a hard-wire ready fire, you will need to wire
the fire into a SWITCHED GROUNDED OUTLET.
THE SOCKET CANNOT BE LOCATED BELOW THE FIRE. It must be located to the side of
the fire. The fire should be fitted in the correct position to the wall before
hard-wiring is completed, so minimal cable is exposed.
in the wall/cavity so there is no visible cable between the fire and the
switched grounded outlet.
Bring the cable out as close to you can as the fire, ensuring it will not be
in the way of any woodwork, suites, or walls being built.
When the fire is fitted you can hard-wire the fire as per the following instructions. Ensure that the switched grounded outlet socket is located in the correct position so that it avoids any interference with any suites or woodwork.
If access is required to the switched grounded outlet, it is advised that the cable is hidden
ELECTRIC FIRES MADE IN EUROPE
25
HARD-WIRE INSTALLATION
01
Fit the switched grounded outlet socket leaving enough power cable to get to
the fire, leaving plenty of wire to trim back.
TIP
Make sure that you disconnect the fuel bed when accessing the fire!
02
You will need to remove the fuel bed from the fire to hard-wire the appliance.
To do this, you will need to remove the 2 screws located at either side of the
fire.
IMPORTANT
Be careful and disconnect the fuel bed from the fire using the connecting
cable found under the fuel bed.
HARD-WIRE INSTALLATION
03
Disconnect the current power bracket found on the right inside the fire.
Remove the terminals from the power inlet and unscrew the bracket from the
fire.
04
Fit the new hard-wire bracket found in the accessory pack by screwing it to
the fire where the old bracket was removed.
IMPORTANT
Leave the ground cable attached to the new bracket.
05
To connect the fire to the main supply, feed the cable through the rubber
grommet found on the new bracket. Trim the power supply cables leaving 13mm /
1/2″ of bare cable exposed to connect the fire to.
26
ELECTRIC FIRES MADE IN EUROPE
ELECTRIC FIRES MADE IN EUROPE
27
HARD-WIRE INSTALLATION
06
Trim the fire power cables by removing the terminals and leave 13mm / 1/2″ of
cable exposed to connect the electrical supply. The Neutral gray cable is a
twin cable.
HARD-WIRE INSTALLATION
08
Now the main cables are connected connect the fire by inserting the trimmed
cables into the corresponding connector. The neutral is a double cable and
both should go into the same side of the connector (pictured below). Make sure
all the connectors are secure and do not come loose. Make sure you connect the
ground cable from the main to the ground cable fitted to the new hard-wire
bracket.
07
In the hard-wire pack there are 3 clear cable connectors. Place the connectors
directly on the end of 3 cables from the main supply cable by lifting the
orange leavers and inserting the wire into one side of the connector. Make
sure there is no bare cable showing and re-close the connector checking the
cable is securely fastened.
02
TIP
Strip back to 13mm / 1/2″ of exposed cable
01
28
ELECTRIC FIRES MADE IN EUROPE
LIVE FROM MAIN ORANGE LIVE FROM FIRE
GROUND FROM MAIN GROUND FROM FIRE
DOUBLE NEUTRAL FROM FIRE NEUTRAL FROM MAIN
ELECTRIC FIRES MADE IN EUROPE
29
HARD-WIRE INSTALLATION
09
Before reinstalling the fuel bed, remove the cable clip from the hard-wire
bracket and use it to secure the electrical cable in place making sure that
nothing can be disconnected if the cable is accidentally pulled.
10
Finally, now everything is connected and secure reconnect the fuel bed cable
and screw the fuel bed back in position.
REAR SCREEN OPTIONS
E-FX FIRES
As standard one of the two rear screens in the E-FX fire has a reflective
coating to mirror the log effect. When the fire is on the flame simulates a
three-dimensional burn between the log effect and the reflection generated by
the coating. If your preference is non-reflective the glass with the
reflective coating can be removed leaving only the projection screen in place.
WARNING
Before any maintenance is undertaken always disconnect the fire from the main
power supply.
NON REFLECTIVE SCREEN OPTION 01
To remove the reflective rear glass take out the fuel bed by removing the two
screws at either side. Gently lift the right side then disconnect the cable
from the fuel bed below the connector marked “A”. Once this is done you may
now carefully remove the fuel bed.
30
ELECTRIC FIRES MADE IN EUROPE
ELECTRIC FIRES MADE IN EUROPE
31
REAR SCREEN OPTION
02
Remove the rear glass leaving the projection screen in place. You can then
reconnect the fuel bed and screw it back into place.
FRONT GLASS INSTALLATION
01
Remove the decorative rail from the top front lip of the fire; it is held on
with using magnets – this will just pull off.
02
Push the side glass back to the rear of the case. This will give you room to
fit the front glass in the next steps.
32
ELECTRIC FIRES MADE IN EUROPE
ELECTRIC FIRES MADE IN EUROPE
33
FRONT GLASS INSTALLATION
03
You will notice a long gap on the underside of the opening in front of the
heater grills. Make sure the magnets on the glass are facing you.
04
At an angle push the glass up into this gap then straighten. Make sure the
bottom of the glass clears the lower edge of the fire opening.
05
Carefully lower into the large channel that runs across the bottom front lip
avoiding the dampers.
FRONT GLASS INSTALLATION
06
Fit the glass handle by using a hex key to adjust the screw before fitting and
then slide the handle onto the glass. Check it is aligned with the cut-out on
the trim and fitted securely.
07
Replace the top decorative rail above the glass and clean the side glass using
a soft clean cloth and pull the side glass forward as pictured.
TIP
Make sure all the glass is clean cleaning it with a non abrasive cloth before
pulling the side glass forward. You want the best view possible from your fire
34
ELECTRIC FIRES MADE IN EUROPE
ELECTRIC FIRES MADE IN EUROPE
35
INFORMATIONAL REQUIREMENTS
E-FX
E-FX: INFORMATIONAL REQUIREMENTS FOR ELECTRIC LOCAL SPACE HEATERS
MODEL
1000 – 40″
1300 – 51″
1500 – 59″
1800 – 70″
Item @ 120V 60Hz or 240V 50Hz
Symbol
Value
Value
Value
Value
HEAT OUTPUT
Nominal Heat Output
Pnon
1.5
1.5
1.5
1.5
Minimum Heat Output (Indicative)
Pmin
0.75
0.75
0.75
0.75
Maximum Continuous Heat Output
PMax,c
1.5
1.5
1.5
1.5
AUXILIARY ELECTRICITY CONSUMPTION
At Normal Heat At Minimum Heat In Standby Mode
elmax elmin elSB
0.0312 0.0312 0.0005
0.0423 0.0423 0.0005
0.0437 0.0437 0.0005
0.0658 0.0658 0.0005
With Distance Control: Yes Room temperature control with Open Window Detection: Yes Adaptive Start with electronic room temperature control plus week timer: Yes
Unit
kW kW kW
kW kW kW
MAINTENANCE
WARNING!
Before any wiring work is undertaken, make sure the power for the socket has
been turned off at the fuse box and check that the power is off. Make sure the
unit is disconnected from any power source. Ensure proper safety precautions
are taken before attempting any work. Maintenance MUST be undertaken by a
qualified technician. Please contact your local retailer where you purchased
the fire from.
PLACE DEALER CONTACT DETAIL STICKER HERE
36
ELECTRIC FIRES MADE IN EUROPE
ELECTRIC FIRES MADE IN EUROPE
37
TROUBLE SHOOTING
PROBLEM
CAUSE
SOLUTION
Electrical lead not plugged in Check lead in plugged in securely and p-clipped in place
NO POWER TO FIRE
Circuit board
Replacement part required
Main socket
Check socket is switched on
NO LIGHTING OR ILLUMINATION
Dimmer turned down LED failure
Use remote or app to adjust the dimmer settings Replacement part required
LED cable connections
Ensure all connections are secure and fully in place
LED FLICKERING
Damaged cable
Replacement part required
Faulty LED
Replacement part required
FLAME ILLUMINATED WITHOUT MOVEMENT
LOGS NOT FULLY ILLUMINATED
ACROSS THE FIRE
HEATER BLOWING COLD AIR
HEATER NOT COMING ON AT ALL
HEAT TURNS OFF QUICKLY AFTER TURNING ON FRONT GLASS WILL NOT FIT
Spindle Motor Log wiring & connectors Log LED Fuel bed LED
The safety cut out may have operated
Trip switch not engaged Thermostat is set to low Thermostat is set to low
Debris is front channel
Check spindle is securely attached to the motor
New Motor maybe required
Remove glass; check each log is tightly connected together
Replacement log maybe required
Replacement part required
Check for obstruction around the heater. If continually a problem and fitted
into a cavity wall or chimney breast,
check with installer that the opening has been 100% fully sealed from drawn
air and draft
Check that the glass is pushed fully back. An audible click lets you know it
is engaged
Use the remote or app or keypad to increase the temperature
Use the remote or app or keypad to increase the temperature
Remove any obstructions and fit
38
ELECTRIC FIRES MADE IN EUROPE
TROUBLE SHOOTING
PROBLEM REMOTE CONTROL NON RESPONSIVE
FRONT GLASS WILL NOT MOVE FREELY
GLOWING LOGS NOT WORKING
RHYTHMIC TICKING
CAN NOT PAIR FIRE
CAUSE Lost connection to fire
Batteries Debris from fuel bed
in channel Fitted incorrectly
SOLUTION Turn fire off & on using the rocker switch next to keypad
and re-pair the remote. See App instructions. Replace with 2 x AAA
Remove debris
Refer to Installation Instructions
Poor connection
Check all connections are secure
Damaged cable
Replacement part required
LED faulty
Replacement part required
Lights turned down Cable loose
Space after email
Use app or remote to turn lighting up
Make sure all flame effect LED’s are tied back to the LED bar and out the way
of the spindle.
Remove space from email
Wrong Wi-Fi password
No 2.4ghz required network available
Check password entered correctly Check 2.4GHz internet connection. Restart Router
ELECTRIC FIRES MADE IN EUROPE
39
Flame Effect LED Strips LED DRIVER
WIRING DIAGRAM
12V Motor Trip Switch
40
ELECTRIC FIRES MADE IN EUROPE
Keypad Control Thermostat
Downlights and Fuelbed LED Strips
Metal Case Ground Stud 120V 60Hz or 240V 50Hz Power Supply
Heater
PARTS LIST
PART NUMBER
1
PART NAME Top Hanging Bracket
2
Bottom Hanging Bracket
3
Power Lead
4
Spindle Motor
5
Spindle
6
Trip Switch
7
PCB Board
8
Glass Handle
9
Front Deco Rail
10
Side Deco Rail
11
Front Glass
12
LED Driver
13
150mm LED
14
Fuel Bed Tray
15
Rear Glass
16
Projection Screen
17
Patent Glass
18
280mm LED
19
Heater
20
Keypad
21
Power Switch
24
Outer Blanking Plate
25
Inner Blanking Plate
26
Remote
27
Top Dressing Rail
E-FX
1000 (40″)
1300 (52″)
M74 M73 E90-2 E99 M24 E59 E50 C54 M49 M49 G9 E42 E3 FE42 G16 FE44 G8 E76 E17-1 E50 E77 M72 M72 E47-2 M146
M76 M75 E90-2 E99 M21 E59 E50 C54 M39 M39 G11 E42 E3 FE46 G18 FE48 G10 E76 E17-1 E50 E77 M72 M72 E47-2 M147
1500 (59″) M78 M77 E90-2 E99 M22 E59 E50 C54 M40 M40 G13 E42 E3 FE50 G21 FE52 G12 E76 E17-1 E50 E77 M72 M72 E47-2 M148
1800 (70″) M80 M79 E90-2 E99 M23 E59 E50 C54 M42 M42 G14 E42 E3 FE189 G23 FE54 G8 x2 E76 E17-1 E50 E77 M72 M72 E47-2 M149
ELECTRIC FIRES MADE IN EUROPE
41
EXPLODED DIAGRAM
2
19 13
20 1
21 24 25
18
17
16
15 14 13
42
ELECTRIC FIRES MADE IN EUROPE
3 26
5 4
11 12
10 9
76 8
CLEANING & MAINTENANCE
· To clean your fire make sure the power is off at the circuit breaker and the
heater is cool before cleaning.
· Wipe with a clean dry cloth that is free from lint and dust. Do not use
cleaning chemicals or abrasives.
· Check the heater is free from any dust by wiping the surface with a clean
dry cloth. This should be done weekly at a minimum.
· All other servicing should be performed by a qualified service personnel.
WARRANTY
3 YEAR WARRANTY
European Home warrants all Flamerite electric fireplaces against defects in
materials and workmanship for a period of THREE (3) YEARS from the date of
original retail purchase. If a defect exists, European Home will, at its
option, either (1) repair the product at no charge, using new or refurbished
replacement parts or (2) exchange the product with one which is new or which
has been manufactured from new or serviceable used parts and is at least
functionally equivalent to the original product. A replacement product/part
assumes the remaining warranty of the original product or ninety (90) days
from the date of replacement or repair, whichever provides longer coverage for
you. When a product or part is exchanged, any replacement item becomes your
property, and the replaced item becomes the property of European Home. Nothing
in the above shall be deemed to imply that this warranty shall apply to work
which has been abused or neglected or shows evidence of changes or
modifications by others with or with-out permit, damages caused by the acts of
God, building settlement or moving, fire or vandalism. In addition,
installation of this product that varies from the requirements stated in the
instruction manual will void the warranty.
ELECTRIC FIRES MADE IN EUROPE
43
www.flameritefires.com/efx
Flamerite Fires Ltd, Greenhough Road, Lichfield, Staffordshire WS13 7AU Tel:
+44 1543 251122 | Fax: +44 1543 251133 | Email: info@flameritefires.com
These products are only suitable for well insulated spaces or occasional use.
Manufactured in the United Kingdom. All products are protected by patents,
registered design and intellectual property rights. Flamerite Fires Ltd. will
protect these rights. All specifications are correct at the time of publishing
but are subject to change.
Read User Manual Online (PDF format)
Read User Manual Online (PDF format) >>