VELOSSA TECH 2019-2022 Hyundai Veloster N BIG MOUTH LIT KIT Ram Air Intake Installation Guide
- July 22, 2024
- VELOSSA TECH
Table of Contents
VELOSSA TECH 2019-2022 Hyundai Veloster N BIG MOUTH LIT KIT Ram Air
Intake
Product Specifications
- Product Name: Hyundai Veloster N BIG MOUTH LIT KIT Ram Air Intake
- Compatibility: 2019-2022 Hyundai Veloster N
- Installation Time: 2 hours
- Tools Required: Basic hand tools
Product Usage Instructions
Kit Contents (Full Kit)
- Diode Dynamics RGBW Controller – Qty: 1
- Positive Cable w/ In-Line Fuse – Qty: 1
- Power Cable w/ Pigtail Connector – Qty: 1
- Switch – Qty: 1
- Switch Ground Cable w/ Pigtail Connector – Qty: 1
- 8 Zip Ties – Qty: 5
- M6 x 12mm Cap Screw – Qty: 1
- M6 Lock Nut – Qty: 1
- Assembled LIT KIT BIG MOUTH – Qty: 1
Stock Components Removal
- Remove the bumper prior to installation. Refer to online resources for bumper removal guides.
- Remove the OEM air shield component by unscrewing the 10mm bolts. This piece will not be reused.
- Remove the shroud. This piece will not be reused.
Install the LIT BIG MOUTH Flare
If you purchased a full LIT kit, follow the instructions below:
- Attach the supplied cable clip to your BIG MOUTH as shown, providing enough slack for the cable.
- Fasten the cable clip securely.
If you purchased a LIT flare-only and already have a Gen 4 BIG MOUTH:
- Remove the old flare and install the LIT flare using the provided screws.
Wiring Harness Installation
- Follow the wiring harness schematic provided in the manual for proper connection of components.
- Ground the pigtail harness using the M6x12 bolt supplied in the kit.
Controller Installation
Zip tie the controller behind the driver side headlight to the OEM
electrical harness using two zip ties for secure placement.
Frequently Asked Questions (FAQ)
-
Q: Can I install the LIT kit without prior experience?
A: While some basic mechanical knowledge is required, following the provided instructions carefully should allow for successful installation. -
Q: Do I need to purchase additional tools for installation?
A: No, basic hand tools are sufficient for installing the Hyundai Veloster N BIG MOUTH LIT KIT.
2019-2022 Hyundai Veloster N BIG MOUTH “LIT KIT” Ram Air Intake Installation Guide
Kit Contents (Full Kit)
Please review this document before attempting installation.
You will need basic hand tools and 2 hours of installation time.
This product reuses some OEM hardware.
Kit Contents (LIT Flare Only)
Please review the table below and make sure you have received the kit
contents.
If you already own the Velossa Tech GEN 4 Veloster N BIG MOUTH, skip to slide 7 to If you already own the Velossa Tech GEN 4 Veloster N BIG MOUTH, skip to slide 7 to
Stock Components Removal
REMOVE BUMPER PRIOR TO ATTEMPING INSTALLATION. Use YouTube as a resource, there are many bumper removal videos to guide you.
Stock Components Removal
Once the bumper is removed, you will need to remove the one OEM component shown below.
Stock Components Removal
Once the bumper is removed, you will need to remove the one OEM component
shown below.
Install the LIT BIG MOUTH Flare
SKIP THIS SLIDE IF YOU PURCHASED A FULL “LIT KIT”
Attach the supplied cable clip to your BIG MOUTH as shown. Fasten the cable
and provide enough slack to not strain the cable.
If you purchased a LIT flare-only and already have a Gen 4 BIG MOUTH. Remove old flare and install the LIT flare with the 4 screws as shown.
Wiring Harness
Wiring Harness Schematic
Install the LIT BIG MOUTH Flare
Controller
Zip tie the controller to the following location behind the driver side
headlight. The controller is zip tied to the thick OEM electrical harness
using two zip ties, one zip tie should loop through the DD controller slot and
the other zip tie goes around the body and plug.
Wire Management
Ground the pigtail harness using the M6x12 bolt supplied in the kit.
Wire Management
You may zip tie the other 3 ports as shown.
Power Hook-up
There will be excess power wire coming out of the power connector, bundle it
neatly and zip tie, leave about a foot of power wire to make the power
connection.
Power Hook-up
Tuck away the bundle as shown, fasten power lug to (+) terminal in the fuse
box on top of the OEM stud, use supplied M6 nut.
Switch groun d: Optional
Phone App
Download the Diode Dynamics app and connect via Bluetooth.
How to connect to the app
- After installing the app from the app store, open the app on your device.
- Cycle the power to the Bluetooth controller by unplugging it and plugging it back in or flick the power switch and wait a few seconds, then turn it back on.
- Wait for the app to detect the controller, it will pop up on the app screen as a Bluetooth controller. If necessary, cycle the power once more to refresh the controller.
- Once the controller shows up on the app, click it and connect. You have 30 seconds to select the controller once it shows up on the app. After 30 second you will need to refresh again to detect the controller again.
- Note that if you mounted your controller behind a lot of metal components, this may degrade the signal and range.
Finalize
Re-install the bumper the same way it was removed and ENJOY!
Read User Manual Online (PDF format)
Read User Manual Online (PDF format) >>