AquaAmp 515-1 Waterproof Wireless Charging Phone Holder Installation Guide
- July 21, 2024
- AquaAmp
Table of Contents
AquaAmp 515-1 Waterproof Wireless Charging Phone Holder
Specifications:
- Input Voltage Range: 10-30V DC (12 / 24V system)
- Input Current Max: 2A
- Output Power: 15W (9V, 1.66A)
- Standby current Draw: < 0.3W
- Waterproof rating: IPx6 front and back
- Certifications: Qi, CE, FCC, ROHS, UNECE R10 E24, RCM
Product Usage Instructions
Step 1: Identify Installation Location
The charger should be installed in a flat area where the back of the
charger is completely flush with the surface it is being mounted to. Confirm
that the clamping arms of the charger are able to be fully extended without
interference. It is recommended to install the charger vertically to better
secure your phone in rough conditions.
Step 2: Spread Clamping Arms and Insert Spreader Bar
Spread the clamping arms of the charger and insert the provided Spreader
Bar into the wireless charger as instructed.
Step 3: Attach Wires to Power Supply
Using a 2A fuse, attach wires to a 12/24V power supply ensuring a
waterproof connection.
Step 4: Test Installation
Check that the charger was installed correctly by placing a wireless
charging compatible device on the charger. Verify that the device starts
charging within a few seconds.
FAQ:
-
Q: What tools are required for installation?
A: You will need a Phillips Head Screwdriver, an Electric Drill, and optionally 3M 5200 adhesive. -
Q: What certifications does the product have?
A: The product is certified with Qi, CE, FCC, ROHS, UNECE R10 E24, RCM.
Parts Provided
Tools Required
Technical Information
Input Voltage Range | 10-30V DC (12 / 24V system) |
---|---|
Input Current Max | 2A |
Output Power | 15W (9V, 1.66A) |
Standby current Draw | < 0.3W |
Waterproof rating | IPx6 front and back |
Certifications | Qi, CE, FCC, ROHS, UNECE R10 E24, RCM |
Installation Guide
Step 1: Identify the installation location. The charger should be
installed in a flat area where the back of the charger is completely flush
with the surface it is being mounted to. Confirm that the clamping arms of the
charger are able to be fully extended without interference. We recommend that
you install the charger vertically to better secure your phone in rough
conditions.
Step 2: Carefully place the provided Installation Template in the
selected location. In the designated areas, drill pilot holes for the mounting
screws using a 3/32” drill bit and then drill a hole for the power wire using
a ¼” drill bit. Remove installation template when complete.
Step 3: Spread the clamping arms of the charger and insert the provided Spreader Bar into the wireless charger as shown below.
Step 4: Thread the wireless charger’s power wire through the ¼” drill hole. Re-confirm that the clamping arms of the charger can be fully extended without interference. Align the charger’s mounting holes with the 3/32” drill holes and screw charger in place with the provided self tapping screws.
Step 5: Using a 2A fuse, attach wires to a 12/24V power supply and ensure there is a waterproof connection
Step 6: Make sure the charger was installed correctly by placing a wireless charging compatible device in the charger. Check that the device is charging a few seconds after you place it on the wireless charger.
Technical Information
Input Voltage Range | 10-30V DC (12 / 24V system) |
---|---|
Input Current Max | 2A |
Output Power | 10W (9V, 1.66A) |
Standby current Draw | < 0.3W |
Waterproof rating | IPx6 |
Certifications | Qi, CE, FCC, ROHS, UNECE R10 E24, RCM |
Contact:
orders@aquaamp.com
1108 Eldridge St, Clearwater, FL 33755
For further information visit www.aquaamp.com