HORI MarioKart Racingwheel Pro DX Instruction Manual
- July 17, 2024
- HORI
Table of Contents
HORI MarioKart Racingwheel Pro DX
Specifications
- Model: 2055-50MKUS
- Platform: Nintendo SwitchTM / PC(Xinput)
- Supported OS: System requirements USB Port, Internet Connection
- Connection: USB Connector
Product Usage Instructions
How to Connect
Make sure that the direction of the modular plug is correct before
connecting. This product can be used without the foot pedals.
Modular Plug Connection Port: Turn the steering wheel to its maximum rotation position once in both directions. Press down fully into each of the L pedal and R pedal once. Repeat the process when reconnecting the controller or restarting the Nintendo SwitchTM or PC system.
Included
- Steering Unit
- Foot Pedals
- Suction Cups
How to Mount
Steering Unit
Option 1 : Suction Cup
- Remove dust and dirt from the tabletop before securing the controller using the five suction cups.
- Attach suction cups to the steering unit during setup.
Option 2 : Clamp
- Tighten the clamp screw into the steering wheel base.
- Use the clamp to secure the steering unit to a flat, hard surface (e.g., table).
- Do not combine both securing methods as it may damage the suction cups. Avoid affixing to fragile materials.
Control Toggle Switch
Directional pad controls: Can be toggled to directional pad, left stick, or right stick controls. This product’s directional pad toggle function is not guaranteed to work with all software. Check software instruction book for compatibility. This product does not support Analog mode.
Button Hold function
How to Enable: Press and hold the Hold button for 1 second until the red
LED turns on.
How to Disable: Press once. The red LED turns off.
FAQ Caution Note: When playing Mario Kart, ensure proper setup and configuration for optimal performance.
Instruction manual
Thank you for purchasing this product.
Before using this product please read the instructions carefully. After
reading the instruction manual, please keep it for reference.
How to Connect
- Make sure that direction of modular plug is correct before connecting.
- This product can be used without the foot pedals.
Turn the steering wheel to its maximum rotation position once in both
directions. Press down fully into each of the L pedal and R pedal once.
Please repeat the process when you re-connect the controller or restart the
Nintendo Switch™ or PC system.
Included
Platform
Nintendo SwitchTM / PC(Xinput)
Functions as PC controller through XInput. This product does not support
DirectInput.
Supported OS | Windows®10 / 8 ~ 8.1 / 7 |
---|---|
System requirements | USB Port, Internet Connection |
Important Make sure that your Nintendo SwitchTM is updated with the latest system software.
May not function for titles that require motion control.
Layout
How to Mount
Steering Unit
- Option 1 : Suction Cup
- Remove all dust and dirt from your tabletop before securing the controller using the five suction cups.
- Attach suction cups to steering unit when setting up.
- Option 2: Clamp
- Tighten the clamp screw into the steering wheel base.
- Use the clamp to secure the steering unit to a flat hard surface (i.e. table).
- Do not combine both securing methods as it may damage the suction cups.
- Do not affix to furniture made from glass or other fragile materials.
- Detach from furniture carefully to prevent damage to furniture or product.
Foot Pedals
Place foot pedals onto a flat surface.
Control Toggle Switch
Directional pad controls can be toggled to directional pad, left stick or
right stick controls.
This product’s directional pad toggle function is not guaranteed to work with
all software.
Please refer to software’s instruction book. This product does not work with
Analog mode
Button Hold function
Push and hold the Hold button to maintain the pushed state after releasing
your finger.
Button Hold function works only when ITEM button has ITEM function.
CAUTION
- When playing Mario Kart
- While the Button Hold function is enabled: If you want to use the item you pick up, press any of the ZL button / ITEM button / L Paddle once to disable the Button Hold function.
- Then press the button again to use the item.
Assign Mode
You can remap the function of buttons using this feature
Programmable Buttons Assignable Functions
ZL / ZR / LSB / RSB / ITEM / L Paddle / R Paddle / L Pedal / R Pedal A / B / X / Y / L / R / ZL / ZR / LSB / RSB / ITEM / L Paddle / R Paddle Directional Pad (Right / Down / Left / Up) / Left stick (Right / Down / Left / Up) / Right stick (Right / Down / Left / Up)
- After 4 seconds of inactivity between steps, Program LED (Right) will turn off and program mode will stop.
- During steps 2, button input from the controller to the Nintendo Switch™ will be disabled.
- When the Program LED (Left) turns on, it indicates that a button is remapped and will not turn off until button function is reset to default.
- If you want to disable button function, press and hold for 3 seconds the same button you pressed in step 2 at the time of step 3.
- If you pressed multiple buttons during step 3, the last button you pressed will be assigned.
- Controller settings are stored even if the USB is disconnected.
How to reset individual buttons
Use the Step 3 above to individually reset buttons to default.
How to reset all buttons / functions to default
Quick Handling Mode
Adjustable Sensitivity
Steering wheel sensitivity is adjustable to seven levels.
The Program LED (Left) colour will change to indicate the sensitivity value
-
If you do not perform step 1 after 2, the Program LED (Right) will turn off after four seconds and button assignment mode will automatically end.
-
During steps 2~6, only the steering unit and foot pedal input are enabled.
Button input from the controller to the Nintendo Switch™ will be disabled. -
Controller settings are stored even if the USB is disconnected.
| 1| 2| 3| 4| 5| 6| 7
---|---|---|---|---|---|---|---
LED colour| Green| Yellow| Red| Purple| Blue| Light Blue| White
Adjustable Dead Zone
The Dead Zone is adjustable to seven levels.
Program LED (Left) colour will change to indicate the dead zone value.
-
If you do not perform step 1 after 2, the Program LED (Right) will turn off after four seconds and button assignment mode will automatically end.
-
During steps 2~6, only the steering unit and foot pedal input are enabled.
Button input from the controller to the Nintendo Switch™ will be disabled. -
Controller settings are stored even if the USB is disconnected.
| 1| 2| 3| 4| 5| 6| 7
---|---|---|---|---|---|---|---
LED| Green| Yellow| Red| Purple| Blue| Light Blue| White
Reset back to default settings
To simultaneously reset all of the following
Quick Handling Mode
- Dead Zone Adjustment
- Sensitivity Adjustment
When Quick Handling Mode is cancelled, steering wheel input value will default
to 270°.
Dead zone and sensitivity default values are set to “4”.
If you do not perform step 2 after 1, the Program LED (Right) will turn off
after four seconds and button assignment mode will automatically end.
Caution
- Never disassemble, repair, or modify this product.
- Keep the controller away from dusty or humid areas.
- Do not apply strong impact or weight on the product.
- Do not pull roughly or bend the cable of the controller.
- If product needs cleaning, use only a soft dry cloth. Do not use any chemical agents like benzine or thinner.
- Keep this product out of the reach of children under 3.
Main Specifications
THE FCC WANTS YOU TO KNOW
This device complies with part 15 of the FCC Rules. Operation is subject to
the following two conditions
- This device may not cause harmful interference, and
- this device must accept any interference received, including interference that may cause undesired operation.
THE FCC WANTS YOU TO KNOW
This equipment has been tested and found to comply with the limits for a Class
B digital device, pursuant to Part 15 of the FCC Rules.
These limits are designed to provide reasonable protection against harmful interference in a residential installation.
This equipment generates, uses and can radiate radio frequency energy and, if not installed and used in accordance with the instructions, may cause harmful interference to radio communications.
However, there is no guarantee that interference will not occur in a particular installation.
If this equipment does cause harmful interference to radio or television reception, which can be determined by turning the equipment off and on, the user is encouraged to try to correct the interference by one or more of the following measures
- Reorient or relocate the receiving antenna.
- Increase the separation between the equipment and receiver
PRODUCT DISPOSAL INFORMATION
Where you see this symbol on any of our electrical products or packaging, it
indicates that the relevant electrical product or battery should not be
disposed of as general household waste in Europe. To ensure the correct waste
treatment of the product and battery, please dispose of them in accordance
with any applicable local laws or requirements for disposal of electrical
equipment or batteries. In so doing, you will help to conserve natural
resources and improve standards of environmental protection in treatment and
disposal of electrical waste. Applicable to EU countries and Turkey only.
US
Warranty
HORI warrants to the original purchaser that the product purchased new in its original packaging shall be free of any defects in material and workmanship for a period of 90 days from the original date of purchase. If the warranty claim cannot be processed through the original retailer please contact HORI customer support directly at infous@hori.jp Please visit http://stores.horiusa.com/policies/ for warranty details.
EU
Warranty
For all warranty claims made within the first 30 days after purchase, please
check with the retailer where the original purchase was made for details. If
the warranty claim cannot be processed through the original retailer or for
any other inquiries pertaining to our products, please contact HORI customer
support directly at infous@hori.jp
- Warning, Not suitable for children under 36 months, Long cord, Strangulation hazard.
- The image on the package may differ from the actual product.
- The manufacturer reserves the right to change the product design or specifications without notice.
- The wires are not to be inserted into socket-outlets.
- The packaging must be retained since it contains important information.
- HORI & HORI logo are registered trademarks of HORI
MADE IN CHINA
References
Read User Manual Online (PDF format)
Read User Manual Online (PDF format) >>