Horipad For Nintendo Switch Instruction Manual
- June 7, 2024
- HORI
Table of Contents
Horipad For Nintendo Switch Instruction Manual
Caution
Warning: Not suitable for children under 36 months. Small parts.
Please read carefully before using this product. Keep this product away from
children. Do not drop or throw this controller.
Do not pull roughly or bend the cable of the controller. Keep the controller
away from dusty or humid areas. If product needs cleaning, use only a soft dry
cloth. Do not use any chemical agents like benzine or thinner.
Included
Platform
Nintendo Switch:
Not compatible with games requiring motion control.
Layout
-
Left Stick
Left Stick Button -
Capture Button
-
TURBO Button
-
HOME Button
-
USB Connector
-
Controller Cable
-
– Button
-
+ Button
-
A/B/X/Y Button
-
Control Pad
-
Control Button
-
TURBO LED (Green)
-
Right Stick
Right Stick Button -
ZL Button
-
L Button
-
R Button
-
ZR Button
How to Connect
Please insert the USB connector of the controller into the USB port of the Nintendo Switch Dock.
How to use the Turbo Functions
The Turbo hold function allows continuous rapid fire without having to hold
the button. (Pressing the assigned button deactivates this).
The following buttons can be set to Turbo or Turbo hold mode:
A/B/X/Y/L/R/ZL/ZR/Control Pad (UP)/DOWN/LEFT/RIGHT
Control Pad (UP, DOWN, LEFT or RIGHT) are not compatible with the Turbo hold mode, and can only be set to Turbo mode
By pressing the HOME Button, all Turbo function and Turbo hold settings will be deactivated. When returning back to game play, you will need to reset the Turbo and Turbo Hold setting. Turbo Function may not be compatible with all software titles. Please try adjusting the Turbo settings or simply turn OFF TURBO.
How to change Turbo Speed
You can adjust the Turbo mode to 3 different speeds. While pressing the Turbo
Button, push up on the Right Analog Stick
to change the Turbo speed in the following order: 5 times/second → 12
times/second → 20 times/second. While pressing the Turbo Button, push down on
the Right Analog Stick to change the Turbo speed in the following order:
20 times/second → 12 times/second → 5 times/second Turbo speed is set to 12
times/second by default.
The Turbo LED will flash at a rate corresponding to the Turbo speed for 2
seconds.
Change Control Pad function
The normal function of the product may be disturbed by strong Electro-Magnetic
Interference. If so, simply reset the product to resume normal operation by
following the instruction manual. In case the function dose not resume, please
use the product in another location.
PRODUCT DISPOSAL INFORMATION
[Bin symbol as on the right] Where you see either symbol on any of our
electrical products, batteries or packaging,it indicates that the relevant
electrical product or battery should not be disposed of as general household
waste in Europe. To ensure the correct waste treatment of the product and
battery, please dispose of them in accordance with any applicablelocal laws or
requirements for disposal of electrical equipment/batteries. In so doing, you
will help to conserve natural resources and improve standards of environmental
protection in treatment and disposal of electrical waste. The wires are not to
be inserted into socket-outlets. The packaging must be retained since it
contains important information.
THE FCC WANTS YOU TO KNOW
This equipment has been tested and found to comply with the limits for a Class
B digital device, pursuant to Part 15 of the FCC Rules. These limits are
designed to provide reasonable protection against harmful interference in a
residential installation. This equipment generates, uses and can radiate radio
frequency energy and, if not installed and used in accordance with
theinstructions, may cause harmful interference to radio communications.
However, there is no guarantee that interference will not occur in a
particular installation. If this equipment does cause harmful interference to
radio or television reception, which can be determined by turning the
equipmentoff and on, the user is encouraged to try to correct the interference
by one or more of the following measures: · Reorient or relocate the receiving
antenna. · Increase the separation between the equipment and receiver.
Warranty
HORI warrants to the original purchaser that the product purchased new in its
original packaging shall be free of any defects in material and workmanship
for a period of 90 days from the original date of purchase. If the warranty
claim cannot be processed through the original retailer please address
directly to HORI at infous@hori.jp. Please visit
http://stores.horiusa.com/policies/ for warranty details.
Please retain contact information for future reference. The manufacturer
reserves the right to change the product design or specifications without
notice. The image on the package may differ from the actual product. HORI and
HORI logo are registered trademarks of HORI.
Read User Manual Online (PDF format)
Read User Manual Online (PDF format) >>