DIGITUS DS-55346 Wireless HDMI Receiver Installation Guide

: July 16, 2024
: DIGITUS

Table of Contents

DIGITUS DS-55346 Wireless HDMI Receiver
Product Information
Product Usage Instructions
Introduction
Main Features
Package Content
Technical Features
Panel Description
Supported formats
Connection Diagram
Troubleshooting
References
Read User Manual Online (PDF format)
Download This Manual (PDF format)

DIGITUS DS-55346 Wireless HDMI Receiver

Product Information

Specifications

Input Port: HDMI x 1
Output Port: HDMI x 1, LOOP OUT x 1
Wireless Extension Distance: Up to 100m for 1 to 1 connection
Signal Compressing Latency: 150-200ms
Wireless Extensions Distance: 100m for 1080p
Frequency Band: 5GHz
Wireless Standard: 802.11a
Vertical Frequency Range: 50/60Hz
Compress Formats: H.265
IR Frequency Range: 20-60KHz
Progressive Resolutions: 480p, 576p, 720p, 1080p
Operating Temperature: 0 to 50°C
Storage Humidity: 5% to 90% RH non-condensation
Power Supply: DC 5V
Power Consumption (Max): TX: 3W, RX: 1.5W
Dimension (LxWxH): TX: 115x60x18mm, RX: 172g (TX), 170g (RX)
Material: Metal

Product Usage Instructions

Panel Description

INPUT: HDMI Input
OUTPUT: HDMI Output
DC/5V: DC 5V Input
Loop out: HDMI Loop Out Port for Local View
Reset: Long Press 10 Seconds to Reset, Short Click to Match the Sender and Receiver
IR IN: IR Signal Input Port
IR OUT: IR Signal Output Port
Power LED
Link:
- No Connection: Keep Lighting on
- Get Connection: Flash Quickly
Status:
- No Video Signal: Flash Slowly
- Get Video Signal: Flash Quickly

Supported Formats
The device supports progressive resolutions of 480p, 576p, 720p, and 1080p.

Connection Diagram
(Diagram not provided in this text)

How to Set Up 1 to 4 Connections

Install antennas for Sender & Receiver.
Press the RESET button on the Sender until the Status LED flashes frequently.

Frequently Asked Questions (FAQ)

Problem: No picture after correct connection at one room
Solution: Check the HDMI connections and power supplies of both the Sender and Receiver. Ensure that all devices are properly powered on and that the HDMI cables are securely connected.
Problem: No picture after correct connection at different room
Solution: Verify that the HDMI cables are functioning correctly and try reconnecting them. Ensure that the wireless signal is not being obstructed or interfered with in any way.

Wireless HDMI Receiver for DS-55346

Quick Installation Guide
DS-55347

Introduction

The additional receiver unit for the Wireless HDMI Extender Set / Splitter Set (DS-55346) extends this Multicast system by up to 4 receiver modules and receives your high-resolution HDMI video and audio signals without a cable at a distance of up to 100 m (1:1 connection, unrestricted view). Distribute your media content quickly and easily on up to 4 displays.

Main Features

Extends the Wireless HDMI Extender / Splitter Set (DS-55346) with additional receiver units
Distribute your HDMI signal on up to 4 displays (receivers)
Transfer of HDMI signals in Full HD with max. resolution of 1080p / 60 Hz
IR transmission to control the source device from output display
Plug & Play – no software or driver required
HDMI 1.4, HDCP 1.3

Package Content

1x Receiver unit
1x Antenna
1x Power adapter, cable length: 1.2 m
1 x IR connection cable, 1.2 m
1x User manual

Technical Features

Input Port	HDMI x 1
Output Port	HDMI x 1，LOOP OUT x 1
Wireless Extendsion Distance	1 to 1 connection:up to 100m

1 to 2 connection:up to 75m

1 to 3 connection:up to 40m

1 to 4 connection:up to 25m

Panel Description

1.)	INPUT: HDMI Input
2.)	OUTPUT: HDMI Output
3.)	DC/5V: DC 5V Input
4.)	Loop out: HDMI Loop Out Port for Local View
5.)	Reset: Long Press 10 Seconds to Reset, Short Click to Match

the Sender and Receiver

---|---
6.)| IR IN: IR Signal Input Port
7.)| IR OUT: IR Signal Output Port
8.)| Power LED
9.)| Link

No Connection: Keep Lighting on

Get Connection: Flash Quickly

10.)| Status

No Video Signal: Flash Slowly

Get Video Signal: Flash Quickly

Supported formats

Simple Plug and Play, no software installation required
Support 5GHz single frequency wireless A/V transmission
Wireless extension of HDMI up to 100 meters (330 feet) with no obstruction
Compliant with HDCP1.3
Support highest video resolution 1080p
Support Point-to-Point and Multicast transmission (up to 4 receivers)
Support infrared remote to control source device from the display side
Support uncompressed audio such as LPCM
Support audio sampling rate up to 48 KHz

Connection Diagram

How to set up 1 to 4 connections:
The factory setting of Sender and Receiver have matched the signal already, you can connect the input and output devices with this item directly. If the customer wants to connect 2, 3 or 4 receivers, please see below:

Step 1: Install antennas for Sender & Receiver.

Step 2: By pressing “RESET” button first, the Sender will be connected with power until the Status Led flashes frequently. Then it will take approximately 7s from power on to enter matching mode. The 1.2.3 or 4 Receivers follow the same steps as the Sender.

Step 3: When the Status Led of the Receiver (1,2,3,4) flashes frequently, it means it entered the matching mode.

Step 4: Open HDMI male to male cable (Not Included) to match the signal.

Step 5: Connect “HDMI IN” of the Sender and “HDMI OUT” of the Receiver (1,2,3,4) with HDMI cable.

Step 6: When the Status Led of the Receiver (1,2,3,4) is permanently on, it means the signal matching is successfully.

Step 7: Make sure the Sender and Receiver (1,2,3,4) are not powered. Step 8: Connect power of the Sender and Receiver (1,2,3,4), then connect HDMI cable to the “INPUT” of the Sender to HDMI sourcing device and the “OUTPUT” of Sender (1,2,3,4) to the display or TV. Step 9: The display or TV will show “Searching TX” about 5s to 35s. Step 10: Matching successfully.

Troubleshooting

Problems	Causes	Solutions
No picture after correct connection at one room	Maybe the sender and receiver

have not yet matched

the connection

| Follow the matching steps to match the signal of the Sender

and Receiver

than 70 m. When

crossing a solid wall.

The picture is not	There may be	Please move the
stable or the	some sources of	device closer to the
distance is shorter	interference in the	location where
than the	same frequency	sources of
description	band at 5GHz that	interference with the
affect the signal

transmission of

| same frequency band

are located or remove

| the extender.| the sources of
| | interference.

Disclaimer
Hereby ASSMANN Electronic GmbH declares that the Declaration of Conformity is part of the shipping content. If the Declaration of Conformity is missing, you can request it by post under the below mentioned manufacturer address.

www.assmann.com
Assmann Electronic GmbH
Auf dem Schüffel 3
58513 Lüdenscheid
Germany