DIGITUS DS-55346 Wireless HDMI Extender / Splitter Set Installation Guide

DIGITUS DS-55346 Wireless HDMI Extender / Splitter Set

Specifications:

• Input Port: HDMI x 1
• Output Port: HDMI x 1, LOOP OUT x 1
• Wireless Extension Distance:
  • 1 to 1 connection: up to 100m
  • 1 to 2 connection: up to 75m
  • 1 to 3 connection: up to 40m
  • 1 to 4 connection: up to 25m
• Signal Compressing Latency: 150-200ms
• Wireless Extensions Distance: 100m (330 feet) for 1080p
• Frequency Band: 5GHz
• Wireless Standard: 802.11a
• Vertical Frequency Range: 50/60Hz
• Compress Formats: H.265
• IR Frequency Range: 20-60KHz
• Progressive Resolutions(50&60Hz): 480p, 576p, 720p, 1080p
• Operating Temperature: 0 to 50°C
• Storage Humidity: 5% to 90% RH non-condensation
• Power Supply: DC 5V
• Power Consumption (Max): TX: 3W, RX: 1.5W
• Dimension(LxWxH): TX: 115x60x18mm, RX: 115x60x18mm
• Net Weight: TX: 172g, RX: 170g
• Material: Metal

Product Usage Instructions

Panel Description:

1. INPUT: HDMI Input
2. OUTPUT: HDMI Output
3. DC/5V: DC 5V Input
4. Loop out: HDMI Loop Out Port for Local View
5. Reset: Long Press 10 Seconds to Reset, Short Click to Match the Sender and Receiver
6. IR IN: IR Signal Input Port
7. IR OUT: IR Signal Output Port
8. Power LED
9. Link:
   • No Connection: Keep Lighting on
   • Get Connection: Flash Quickly
10. Status:
    • No Video Signal: Flash Slowly
    • Get Video Signal: Flash Quickly

How to set up 1 to 4 connections:

1. Install antennas for Sender & Receiver.
2. Press RESET button on Sender until Status LED flashes frequently.
3. Follow the same steps for Receivers (1,2,3,4).
4. Open HDMI male to male cable to match the signal.
5. Connect HDMI IN of Sender and HDMI OUT of Receivers with HDMI cable.
6. Wait for Status LED of Receivers to be permanently on.
7. Power off Sender and Receivers.
8. Connect power and HDMI cables as instructed.
9. The display will show “Searching TX” for a few seconds.
10. Matching successfully completed.

Frequently Asked Questions (FAQ):

Problem:
No picture after correct connection at one room.

Cause:
The sender and receiver have not yet matched the connection.

Solution:
Follow the matching steps to match the signal of the Sender and Receiver.

Problem:
No picture after correct connection at different room.

Cause:
The distance can’t reach 100m due to signal loss passing through solid walls.

Solution:
When passing through a solid wall (thickness less than 30 cm), the signal loses 30% of the original signal and the distance is shorter than 70m. When crossing two or more solid walls, the distance is shorter than 20 meters. Please select a shorter distance when crossing a solid wall.

Introduction
Experience ultimate flexibility and performance for the transfer of your Full HD AV signals with our wireless transfer system, which offers a range of up to 100 meters in a 1:1 connection with unobstructed view. Our system supports both Point-to-Point and Multicast (Point-to-Multipoint) transfers, which allows you the freedom of transferring your AV signal to multiple displays at the same time or connecting a single source with various target devices. With a maximum resolution of 1080p / 60 Hz, our system guarantees sharp and smooth reproduction of your content. You can also expand your system easily for up to 4 receiver units (DS-55347), to achieve video splitter functionality and share your HDMI signal on up to 4 displays. The transmission module features an additional HDMI output (loop-out) which enables you to connect an external monitor, while integrated IR transmission allows for convenient control of your source device directly from the output display (receiver unit). Our Plug & Play system does not require any additional software or driver installation and is ready for immediate use.

Main Features

• Wireless transfer of Full HD AV signals over a distance of up to 100 m (1:1 connection, unobstructed view)
• Supports Point-to-Point and Multicast (Point-to-Multipoint) transfer
• Transfer of HDMI signals in Full HD with max. resolution of 1080p / 60 Hz
• Expandable for up to 4 receiver units (DS-55347) and offers video splitter functionality with additional receivers
• Distribute your HDMI signal on up to 4 displays
• Additional HDMI output (loop-out) on transmitter module for connection to an external monitor
• IR transmission to control the source device from output display
• Plug & Play – no software or driver required
• HDMI 1.4, HDCP 1.3

Package Content

• 1x Transmitter unit
• 1x Receiver unit
• 2x Antenna
• 2x Power adapter, cable length: 1.2 m
• 2 x IR connection cable, 1.2 m
• 1x User manual

Technical Features

1 to 2 connection:up to 75m
1 to 3 connection:up to 40m
1 to 4 connection:up to 25m
Signal Compressing Latency| 150-200ms
Wireless Extensions Distance| 100m (330 feet) for 1080p
Frequency Band Range| 5GHz
Wireless Standard| 802.11a
Vertical Frequency Range| 50/60Hz
Compress Formats| H.265
IR Frequency Range| 20-60KHz
Progressive Resolutions(50&60Hz)| 480p,576p,720p,1080p
Operating Temperature| 0℃ to 50℃
Storage Humidity| 5% to 90% RH non-condensation
Power Supply| DC 5V
Power Consumption (Max)| TX: 3W, RX: 1.5W
---|---
Dimension(LxWxH)| 115x60x18mm
Net Weight| TX:172g, RX:170g
Material| Metal

Panel Description

Sender and Receiver
6.)| IR IN: IR Signal Input Port
7.)| IR OUT: IR Signal Output Port
8.)| Power LED
9.)| Link
No Connection: Keep Lighting on
Get Connection: Flash Quickly
10.)| Status
No Video Signal: Flash Slowly
Get Video Signal: Flash Quickly

Supported formats

• Simple Plug and Play, no software installation required
• Support 5GHz single frequency wireless A/V transmission
• Wireless extension of HDMI up to 100 meters (330 feet) with no obstruction
• Compliant with HDCP1.3
• Support highest video resolution 1080p
• Support Point-to-Point and Multicast transmission (up to 4 receivers)
• Support infrared remote to control source device from the display side
• Support uncompressed audio such as LPCM
• Support audio sampling rate up to 48 KHz

Connection Diagram

How to set up 1 to 4 connections

The factory setting of Sender and Receiver have matched the signal already, you can connect the input and output devices with this item directly. If the customer wants to connect 2, 3 or 4 receivers, please see below:
Step 1: Install antennas for Sender & Receiver.

Step 2: By pressing “RESET” button first, the Sender will be connected with power until the Status Led flashes frequently. Then it will take approximately 7s from power on to enter matching mode. The 1.2.3 or 4 Receivers follow the same steps as the Sender.

Step 3: When the Status Led of the Receiver (1,2,3,4) flashes frequently, it means it entered the matching mode.

Step 4: Open HDMI male to male cable (Not Included) to match the signal.

Step 5: Connect “HDMI IN” of the Sender and “HDMI OUT” of the Receiver (1,2,3,4) with HDMI cable.

Step 6: When the Status Led of the Receiver (1,2,3,4) is permanently on, it means the signal matching is successfully.

Step 7: Make sure the Sender and Receiver (1,2,3,4) are not powered.

Step 8: Connect power of the Sender and Receiver (1,2,3,4), then connect HDMI cable to the “INPUT” of the Sender to HDMI sourcing device and the “OUTPUT” of Sender (1,2,3,4) to the display or TV.

Step 9: The display or TV will show “Searching TX” about 5s to 35s.

Step 10: Matching successfully.

Troubleshooting

Disclaimer
Hereby ASSMANN Electronic GmbH declares that the Declaration of Conformity is part of the shipping content. If the Declaration of Conformity is missing, you can request it by post under the below mentioned manufacturer address.
www.assmann.com
Assmann Electronic GmbH
Auf dem Schüffel 3
58513 Lüdenscheid
Germany

References

• ASSMANN Electronic GmbH | Germany

Read User Manual Online (PDF format)

Read User Manual Online (PDF format)  >>

Download This Manual (PDF format)

Download this manual  >>