AUDIOSTATUS SB19ST-C000-4 Dome Tweeter Installation Guide

July 16, 2024
AUDIOSTATUS

AUDIOSTATUS SB19ST-C000-4 Dome Tweeter

Specifications:

  • Frequency range: Micro-C: 68 – 28000 Hz +/-3 dB, Micro: 70-28000 Hz +/-3 dB

  • Sensitivity (2.83V / 1m): 84.5 dB

  • Nominal impedance: 4 Ohm

  • Max SPL: 100 dB

  • Recommended amplifier: 25 – 100 W

  • Cross-over frequency: 4000 Hz

  • Speaker type: 2-way Bookshelf

  • Enclosure type: Bass reflex

  • Port tuning frequency: 49 Hz

  • Drive Units:

    • High frequency driver: SB19ST-C000-4
    • Low frequency drivers: Micro-C: SB12CACS25-4, Micro:
      SB12PAC25-4
  • Cabinet Dimensions (H x W x D): 262 x 132 x 170 mm

  • Net Weight (pair): Cabinet only: 4.3 kg / 9.48 lb, Full assembly: 7.8 kg / 17.2 lb

  • Special Features:

    • High performance compact design
    • Optimized drivers
    • Simple high-quality cross-over network
    • Front ring integrated port
    • Versatile placement
    • Solid single wiring binding posts

Product Usage Instructions

Tools Needed:

  • No. 2 Philips screwdriver (for drivers and crossover screw)
  • 11 mm hex socket (for tightening binding post nut)
  • Multipurpose glue (for attaching the damping and sealing the terminal hole)

Assembly Instructions:

  1. Take out the cabinet from the packaging and remove the raw damping material.
  2. Unscrew the binding post nut and attach both binding post terminals on the rear of the cabinet.
  3. Fasten each terminal from the inside of the cabinet using the terminal nuts.
  4. Tighten the nut using an 11 mm hex socket head. Seal the cabinet by applying glue around the nut.
  5. Place the crossover on the rear panel inside the cabinet.
  6. Secure the crossover to the cabinet with four screws, one in each corner.
  7. Connect both crossover input cables to the binding post terminals.
  8. Cut the raw damping material according to the cutting diagram.
  9. Place each part of the damping material in the cabinet according to the damping position diagram. Add glue if needed to hold it in place.

Frequently Asked Questions (FAQ):

  1. Q: What are the recommended amplifier specifications for optimal performance?
    A: The recommended amplifier power range is between 25 to 100 watts for best results.

  2. Q: How do I position the speakers for optimal sound quality?
    A: Place the speakers in a versatile location that suits your listening environment, ensuring proper spacing and alignment with your listening area for balanced sound distribution.

AUDIOSTATUS-SB19ST-C000-4-Dome-Tweeter-\(1\)

Special Features:

  • High performance compact design.
  • Optimized drivers.
  • Simple high quality cross-over network.
  • Front firing integrated port.
  • Versatile placement.
  • Solid single wiring binding posts.

AUDIOSTATUS-SB19ST-C000-4-Dome-Tweeter-\(2\)

Frequency Response (Micro)

AUDIOSTATUS-SB19ST-C000-4-Dome-Tweeter-\(3\)

Measured on-axis, 15° and 30° off-axis at 1 m in an ordinary room. Lower frequency dips and peaks are caused by room modes/reflections.

Mechanical Drawing (dimensions in mm) / Micro-C

AUDIOSTATUS-SB19ST-C000-4-Dome-Tweeter-\(4\)

Mechanical Drawing (dimensions in mm) / Micro

AUDIOSTATUS-SB19ST-C000-4-Dome-Tweeter-\(5\)

AUDIOSTATUS-SB19ST-C000-4-Dome-Tweeter-\(6\)

AUDIOSTATUS-SB19ST-C000-4-Dome-Tweeter-\(20\)

Damping Material Cutting Pattern (dimensions in mm)

AUDIOSTATUS-SB19ST-C000-4-Dome-Tweeter-\(8\)

Damping Material Position (dimensions in mm)

AUDIOSTATUS-SB19ST-C000-4-Dome-Tweeter-\(10\)

Part List (each cabinet)

  • H igh frequency driver SB19ST-C000-4 (sold separately) ……………………………….. 1 pc
  • Low frequency drivers 4” SB12PAC25-4 or 4” SB12CACS25-4 (sold separately) .. 1 pc
  • Micro crossover kit (sold separately)………………………………………………………….. 1 pc
  • Wood Screw 3.5 x 20 mm for tweeter ………………………………………………………4 pcs
  • Wood Screw 4 x 20 mm for woofer …………………………………………………………..4 pcs
  • Wood Screw 4 x 16 mm for crossover (from crossover kit). ……………………………4 pcs
  • Binding post terminal ……………………………………………………………………………..1 pair
  • Damping . ………………………………………………………………………………………………1 pc
  • N ame plate ……………………………………………………………………………………………1 pc

Tools Needed:

  • No. 2 Philips screwdriver (for drivers and crossover screw).
  • 11 mm hex socket (for tightening binding post nut).
  • Multipurpose glue.
    (for attaching the damping and sealing the terminal hole).

Assembly Instructions

  1. Take out the cabinet from the packaging and take out the raw damping material from the cabinet.

  2. Unscrew the binding post nut then attach both binding post terminals on the rear of the cabinet.

  3. Fastern each terminal from the inside of the cabinet using the terminal nuts.

  4. Tighten the nut using 11 mm hex socket head. Put some glue around the nut to seal the cabinet.

  5. Place the crossover on the rear panel inside the cabinet.

  6. Secure the crossover to the cabinet with the four screws. One screw in each corner.

  7. Connect both crossover input cables to the binding post terminals.

  8. Cut the raw damping material according to the cutting diagram.

  9. Place each part of the damping material the cabinet according to damping position diagram. Add a bit of glue if needed to hold the damping material in place.
    damping material the cabinet according to damping position diagram. Add a bit of glue if needed to hold the damping material in place.

  10. Attach the tweeter cables from the crossover to the tweeter terminals, then place the tweeter into the tweeter cutout on the cabinet, align the screw holes to the cabinet screw holes.

  11. Attach the woofer cables from the crossover to the woofer terminals, then place the woofer into the woofer cutout on the cabinet, align the chassis screw holes to the cabinet screw holes.

  12. Fasten the tweeter and woofer screws to the cabinet.

  13. Repeat the steps for the second speaker and you have finished the assembly process. Happy listening!.

www.sbacoustics.com

Read User Manual Online (PDF format)

Read User Manual Online (PDF format)  >>

Download This Manual (PDF format)

Download this manual  >>

Related Manuals