ooni PR230417 Digital Infrared Thermometer Instruction Manual
- July 15, 2024
- Ooni
Table of Contents
Digital Infrared Thermometer
Manual & Safety Instructions
Warnings
This is a Class 2 laser product in accordance with IEC/EN 60825-1:2014.
The radiation pattern emitted from this product:
Wavelength: 635-665 nm
Beam divergence:
X=5.725°
Y=5.725°
Pulse duration: Continuous
Maximum power or energy output: <1mW
A visible laser beam emerges from the front of the product.
Do not stare directly into the laser beam or direct it towards other people or
animals.
Do not submerge in water or use water to clean.
Store out of reach of children.
Do not place fingers inside the product.
Handle with care.
Use environment:
Operating temperature: 0 to +40°C
Operating humidity: <80%
Do not repair this product. Repair must be performed by Ooni or a suitably
qualified person.
This product should not be disposed with other household wastes throughout the
EU and UK. To prevent possible harm to the environment or human health from
uncontrolled waste disposal, recycle it responsibly and promote the
sustainable reuse of material sources. To return your used device, please use
the return and collection systems or contact the retailer where this product
was purchased. They can take this product for environmentally safe recycling.
Batteries must not be disposed of in the domestic waste as they contain
substances which can be damaging to the environment and health. Please dispose
of batteries in designated collection points.
What’s in the box
1 x Ooni Digital Infrared Thermometer
1 x User Manual & Safety Instructions
2 x AAA Batteries
Instructions
The Ooni Digital Infrared Thermometer is used for measuring the temperature of
cooking surfaces within your pizza oven. Direct the laser at your cooking
surface to check the temperature readings from -30°C > 550°C and -22°F >
999°F.
To cook Neapolitan-style pizzas, aim for 842°F (450°C) in the centre of the
baking stone.
Display
[2] Buttons
a. Laser on/off button
b. Mode button
c. Unit button
d. Trigger button
[3] Screen
a. Emissivity mode symbol
b. Battery symbol
c. Main reading
d. Temperature ring
e. Celsius/Fahrenheit unit
f. Max/min temperature
[4] View Options
Press the Mode button to toggle between Standard View and Essentials View.
a. Standard View
b. Essentials View
[5] Emissivity Mode ( )
Emissivity measures the amount of energy radiated from a material’s surface.
In the case of this Digital Infrared Thermometer, it measures thermal energy.
Emissivity mode will help bakers adjust their thermometer’s settings to get
accurate temperature readings off different kinds of materials like a rough
baking stone versus a smooth pizza steel.
The Digital Infrared Thermometer is pre-set at an emissivity of 0.95 which is
standard for most organic materials and is optimised with all Ooni Baking
Stones.
To change the emissivity, press and hold the Mode button for five seconds.
Once in Emissivity Mode, use the Unit button to cycle through the numerical
values. To select a new value and exit Emissivity Mode, press and hold the
Mode button for five seconds. The new value will not be saved if the trigger
is pressed or your thermometer automatically powers off while in Emissivity
Mode.
[6] How to measure temperature
For most accurate temperature readings, Ooni recommends a measuring distance
`D’ of 30cm50cm from the measurement surface.
WARNING! The front of all Ooni ovens can become extremely hot. Always
measure from outside of the oven entrance. Never insert the product into the
oven.
Point the laser at the middle of the measurement surface for an accurate
reading. Press the trigger to measure. The reading will stay on the screen
until the trigger is pushed again or your thermometer automatically powers
off. To scan a surface such as your pizza stone and determine if there are hot
or cold areas before you launch your pizza, simply pull and hold the trigger
and move the laser across the surface. As you move, the thermometer will
display the minimum and maximum temperatures on the surface.
Maintenance & cleaning
To keep your readings accurate, the lens must be clear of dirt, dust, moisture, fog, smoke and debris. To clean the lens, blow off loose particles using clean compressed air. Gently brush any remaining debris away with a moist cotton cloth. Clean the body of the product with a damp sponge or cloth and mild soap. Store your thermometer inside and for extended periods without use, remove the battery to prolong battery life.
Switching off
The Digital Infrared Thermometer will switch off automatically after an extended period of inactivity.
Low Power ( )
When the battery symbol appears, the remaining power is less than 20%.
When the battery symbol flashes, the remaining power is less than 10%.
When the remaining power is less than 5%, only the battery symbol will show.
At this point, replace the product with new batteries.
ooni.com
© 2023 Ooni
Ooni is a registered trademark of Ooni Ltd.
All rights reserved.
PA-A00490
230417 – IR Thermometer – Manual LIT – GX_PA-A00490.indd
25/03/2024 09:19
References
Read User Manual Online (PDF format)
Read User Manual Online (PDF format) >>