SounDigital 2000.4 EVOPS Amplifier Owner’s Manual

SounDigital 2000.4 EVOPS Amplifier

Product Information

Specifications:

• Resistant to moisture, water splash, and dust
• Compact design
• Conformal coated PCB
• Crossover controls variable in Low pass, High pass, and Full Range
• High-efficiency Class D
• Robust construction, resistant to vibrations and bumps
• IP64 rating

Product Usage Instructions

Safety Instructions:
To avoid injury or damage, follow these safety instructions:

• Product installation should be done by a qualified professional.
• Use rubber O-rings when passing cables through metallic walls to prevent cutting and short circuits.
• Unplug the vehicle’s negative terminal before installing any electric equipment to prevent fires or injuries.
• Avoid continuous exposure to sound pressures over 85dB to prevent hearing damage.
• Ensure the amplifier’s installation location does not affect vehicle operation.
• Operate the equipment with automotive DC voltage batteries between 12.6 and 14.4 volts.
• Avoid installing the amplifier in areas exposed to water, dirt, or humidity.
• Choose a well-ventilated place for installation and avoid blocking ventilation windows.
• Clean the amplifier periodically with a brush or dry cloth for thermal efficiency.
• Avoid making holes in critical vehicle components when installing the amplifier.
• Secure cables properly throughout the installation.
• Fix the amplifier securely without grounding to metallic parts of the vehicle to prevent noise issues.
• Wear gloves, safety glasses, and necessary PPE during installation.

Cleaning and Maintenance:
Periodically clean the amplifier with a brush or dry cloth to maintain thermal efficiency. Avoid using liquid cleaners that may damage the components.

Installation:
Follow the Quick Installation Guide included in the package contents for step- by-step instructions on installing the amplifier in your vehicle.

FAQ:

• Q: Can I install the amplifier myself?
  A: It is recommended to have the product installed by a qualified professional to ensure proper installation and avoid any potential damage.

• Q: What should I do if I encounter issues during installation?
  A: If you face any difficulties or have questions during installation, please contact our technical support at info@soundigitalusa.com for assistance.

INTRODUCTION

Dear Consumer,

• Congratulations, you have just acquired a SounDigital product of the highest technology and quality, so we thank you for your trust.
• SounDigital products are made with raw materials of the highest quality standards, and the most modern processes, equipment, and technology are used in their production.

IMPORTANT INFORMATION

• In this manual, you will learn about the product, its features, and characteristics, to obtain the best result and to be able to enjoy your music with SounDigital quality and power.
• Read this manual carefully and follow precisely all the information contained therein, these are very important and allow your amplifier to work optimally. If you think it is necessary, please do not hesitate to contact our technical support at the following contact: info@soundigitalusa.com.

FEATURES

• Resistant to moisture, water splash, and dust;
• Compact design;
• Conformal coated PCB;
• Crossover controls variable in Low pass, High pass, and Full range;
• High-efficiency Class D;
• Robust construction, resistant to vibrations and bumps;
• IP64 rating.

PACKAGE CONTENTS

• 01 2000.4 EVOPS amplifier
• 01 Quick installation guide with warranty certificate
• 01 Allen wrench 2.0mm
• 01 Allen wrench 2.5mm
• 01 Allen wrench 3.0mm
• 01 Soundigital promotional black sticker
• 01 Soundigital promotional white sticker

SAFETY INSTRUCTIONS

To avoid injury to the user or damage to the amplifier, read all safety instructions written on this manual.

Warning!
THIS “WARNING” SIGN ALERTS THE USER OF IMPORTANT INFO. NOT FOLLOWING THESE INSTRUCTIONS MAY CAUSE INJURIES TO THE USER OR DAMAGE TO THE EQUIPMENT.

TECHNOLOGIES

DYNAMIC THERMAL MANAGEMENT – DTM

The DTM is a dynamic thermal recovery system that always maintains the high efficiency of the amplifier by accelerating the thermal exchange of electronic components with the heatsink.

• Patent required.

ULTRA COMPACT PCB
An intelligent layout, with great use of the PCB area and the use of modern components with reduced structure, guarantees SounDigital products a compact design that, at the same time robust and with excellent thermal efficiency.

ROBUST CONSTRUCTION
Thinking about the application of power sports, the product has an extremely robust assembly, both the fixing points and the layout of the PCB were designed to withstand high vibrations, bumps and impacts.

I-POWER SUPPLY

• SounDigital amplifiers are known for their low consumption of battery, and this feature stays on the EVOPS Line. The new I-POWER SUPPLY is even more modern, which replaces the old toroidal transformers with a new generation of “E-E” core transformers delivering efficiency above 90%*, ensuring more hours of sound without battery recharge.
• Efficiency is measured at power supply only.

VIBRATION ABSORPTION SYSTEM – VAS
Our VAS Technology reduces all impact caused by vibration on the electronic circuit board. This can include road vibration and even vibration caused by sound waves, increasing the reliability of our amplifiers.

REDUCED SIZE
The technology used in our amplifiers brings both high performance and power to a compact chassis, providing flexible installation solutions for vehicles with limited space.

FULL RANGE
The 2000.4 EVOPS amplifier is a versatile product that covers the entire audible frequency range, any type of loudspeaker or music program.

MARINIZATION WITH PROTECTION INDEX IP64
The product is protected against the ingress of dust particles and water droplets from all sides, beyond that, the PCB receives a conformal coating treatment to protect the components from moisture.

ASSEMBLING AND DISASSEMBLING THE PLASTIC SEALS

DISASSEMBLING THE PLASTIC SEALS

1. Squeeze the assembled Flexible Plastics Seals;
2. Pull out the plastic seals.

ASSEMBLING THE PLASTIC SEALS

1. Hold the disassembled Flexible Plastics Seals and fit them in their specific housing;
2. Each connector has its specific Plastic Seal;
3. Make sure the Flexible Plastics Seals are perfectly fitted.

PANELS DESCRIPTION

Audio inputs and controls

1

2

| CH1/CH2

CH3/CH4

| Variable crossover control — 45Hz ~ 850Hz
---|---|---
3

4

| CH1/CH2 CH3/CH4| Crossover switch High Pass — Full — Low Pass
5| CH1|
6

7

| CH2

CH3

| Audio inputs — RCA connectors
8| CH4|
9

10

| CH1/CH2

CH3/CH4

| Variable Gain Control
11| Blue| “POWER ON” LED indicator

Power inputs and audio outputs

INSTALLATION SEQUENCE

Warning!
BEFORE PROCEEDING WITH THE INSTALLATION, UNPLUG THE NEGATIVE TERMINAL FROM ALL OF THE BATTERIES, TO AVOID FIRE, AND DAMAGE TO THE AMPLIFIER AND THE USER HIMSELF.

• Mount the amplifier in such a way you have access to the connectors;
• Install the power cables in the vehicle/vessel properly, starting from the battery to the fuse holder or circuit breaker, use the cable with the appropriate size. Make all connections, and install fuse holders or circuit breakers, but without placing the fuses or with the circuit breakers in the “OFF” position;

Warning!
THE MAXIMUM DISTANCE FOR THE INSTALLATION OF THE FUSE/CIRCUIT BREAKER IS 12 INCHES (30cm) AWAY FROM THE BATTERY.

• Connect the power cables into the amplifier, observing the polarity. Connect all the positive cables (+) from the fuse holder or circuit breaker to the positive connector of the amplifier and all the negative power cables from the batteries to the negative connector of the amplifier;
• The ground cable must be as short as possible and must be connected to the negative connector of the battery or vehicle chassis in case of metallic chassis;
• Install the signal input cables in a proper way, distant from the power cables;
• Connect the RCA cables to the head unit and amplifiers;
• Install the audio output cables with the appropriate section, distant from the power and audio input cables;
• Connect the audio output cables to the amplifier and speakers respecting the positive (+) and negative (-) polarities;
• Install the remote cable with the power cables, using a 1.5mm² (15 AWG) cable or thicker;
• Connect the remote power cable to the amplifier’s “REM” terminal at the main unit’s remote power output;
• Before powering the system, verify all the connections and make sure there are no mistakes or short-circuits on the power and ground cables;
• Reconnect the ground of the batteries;
• Check if the head unit is turned off and then place the fuses in the fuse holders or switch the circuit breakers on;
• Turn on the main unit and the amplifier will turn on the “POWER ON” LED indicating that it is in operation.

Warning!
Minimum recommended installation distance between amplifiers*. 1.18in (30mm)

For installations with more than one amplifier, a second unit is not included. Merely illustrative images.

ELECTRICAL DIMENSIONING AND AUDIO INPUTS

ELECTRICAL DIMENSIONING

• For proper operation of your SounDigital amplifier, you need the proper dimensioning of the electrical system and the cables used.
• The table below shows the minimum section of GND cables, +12VDC cables, and speaker output cables according to the power generated by the amplifier.

2000| POWER CABLE (+12VDC)

GROUND CABLE (GND)

| 21mm² (4 AWG)
---|---|---
WRMS| SPEAKER CABLE| 2mm² (14 AWG)

• We recommend the use of only OFC (Oxygen Free Copper) cables for the installation of our products.
• Copper-clad aluminum wire (CCAW) must not be used.

AUDIO INPUTS
RCA inputs

CROSSOVER SET UP

1. “HP” Set variable control in High Pass function.
2. “F” Set variable control in Full Range function;
3. “LP” Set variable control in Low Pass function;

• Change the switch to the “F” position (Full Range) – All frequencies will be reproduced as shown in the graph;
• Change the switch to the “HP” position – Set in the variable control between 45Hz and 850Hz (“A”) where you want to perform the high pass cut filter;
• Change the switch to “LP” position – Set in the variable control between 45Hz and 850Hz (“B”) where you want to perform the low pass cut filter.

WIRING DIAGRAM

4 CHANNELS WIRING DIAGRAM

3 CHANNELS WIRING DIAGRAM

2 CHANNELS WIRING DIAGRAM

GAIN SETTING
Necessary equipment:

• Digital AC voltmeter;
• Media with sine wave test tone 60Hz recorded at 0db;
• Screwdriver 1/8″ ( for gain setting).

Set up procedure:

• This procedure is the same for both gain controls;
• Turn the gain control down;
• Disconnect the output cables from the amplifier outputs;
• Turn off all processing (bass, treble, loudness, EQ, etc.);
• Set the audio player volume to 3/4 of full volume;
• Set the audio player fader control to center position (left and right fader controls);
• Set the crossover selector switch in “F”;
• Use a 60 Hz sine wave;
• Connect the AC voltmeter to the speaker output connectors of the amplifier. Make sure you test the voltage at the correct connectors (+ and –);
• Increase the gain control until the target voltage is observed with the voltmeter (see the chart below);
• Once you have adjusted the amplifier to the correct voltage output, turn off the source unit and reconnect the speaker(s).

MODEL|  | STEREO/POWER| BRIDGE/POWER| STEREO OUTPUT VOLTAGE| BRIDGE OUTPUT VOLTAGE
---|---|---|---|---|---
2000.4| 2Ω| 1Ω / 500W| 2Ω / 1000W| 22.4V| 44.8V
2000.4| 4Ω| 2Ω / 500W| 4Ω / 1000W| 31.6V| 63.2V

Download the tracks for setup at https://soundigitalusa.com/tracks-for-set- up/.

BATTERY CONNECTION DIAGRAM

• When necessary the association of one or more battery banks to supply the necessary current to the amplifier, it is recommended to use batteries of the same brand, model, and if possible the same manufacturing lot so that the system has the maximum performance.
• For an ideal energy performance, we recommend that all batteries be connected to positive and negative busbars and the busbars connected to the amplifier, as shown in the diagram below:

TECHNICAL SPECS

PARAMETERS

| 2000.4 EVOPS 2Ω|

2000.4 EVOPS 4Ω

---|---|---
Power RMS @ 4Ω| 4 x 217W| 4 x 330W
Power RMS @ 2Ω| 4 x 330W| 4 x 500W
Power RMS @ 1Ω| 4 x 500W| N/A
Power RMS (Bridge) @ 4Ω| 2 x 660W| 2 x 1000W
Power RMS (Bridge) @ 2Ω*| 2 x 1000W| N/A
Frequency Response (-3dB)| 5Hz ~ 22kHz| 5Hz ~ 22kHz
Low Pass filter (12dB/octave)| 45Hz ~ 850Hz| 45Hz ~ 850Hz
High Pass filter (12dB/octave)| 45Hz ~ 850Hz| 45Hz ~ 850Hz
Operating Voltage| 9V ~ 16V| 9V ~ 16V
SNR| 90dB| 90dB
Input Sensitivity (RCA)| 0.2 ~ 4V| 0.2 ~ 4V
Input Sensitivity (High-Level input)| N/A| N/A
Current Draw (music)| 85A| 85A
Current Draw (max.)| 171A| 171A
Total Efficiency| 81%| 81%
Damping Factor (@100Hz nominal impedance)| 200| 200
Power Cable| 21mm² (4 AWG)| 21mm² (4 AWG)
Speaker Cable| 2mm² (14 AWG)| 2mm² (14 AWG)
Remote Cable| 1.5mm² (15 AWG)| 1.5mm² (15 AWG)
Recommended Fuse (music)| 100A| 100A

• It is mandatory to install the fuse at a maximum distance of 12 inches from the battery.
• Power at 14.4V @ 60Hz with a maximum THD of 1%.
• POWER RATING ACCORDING TO CTA-2006 INDUSTRY STANDARDS.

DIMENSIONAL DATA

ADDITIONAL INFORMATION

• The values presented are based on measurements performed in SounDigital’s laboratories. All the equipment used in the assays, tests, measurements, and gauging of the technical parameters of SounDigital products were calibrated in certified laboratories, thus ensuring the performance and standard of excellence of the developed products.
• The Manufacturing Process may present variations, and the electronic components may also present changes in values with their nominal parameters. Thus, causing small differences between measurements taken. Small variations in the values presented and divulged by SounDigital are recognized.
  • Updates of information made in this document will always be published and made available for consumer consultation, free of charge, on the brand’s websites. The user is advised to search for the manual in its latest version when necessary.
  • The images presented in this document are representative and merely illustrative; therefore, they do not necessarily correspond to the actual product/model.

Contact Us

• Web: WWW.SOUNDIGITALUSA.COM.
• Facebook: SOUNDIGITALUSA
• Instagram: SOUNDIGITALUSA

References

• SounDigital USA Tracks for Set up

Read User Manual Online (PDF format)

Read User Manual Online (PDF format)  >>

Download This Manual (PDF format)

Download this manual  >>