THUNDERSTONE TSL42 Wireless Microphone User Manual

THUNDERSTONE TSL42 Wireless Microphone

Packing List

Introduction

1. Metal Mesh
2. LED Ring
3. Handle
4. Type-C
5. Power Button

How To Connect

1. Plug the data cable to the receiver.
2. Connect the receiver to Car USB port
3. Press the Power button on the bottom
4. Start in-Car Karaoke Software
5. Start Singing

Note: The receiver should not be placed near large metal objects, and there should be no obstruction between the microphone and the receiver.

Operation Manual

Power On/Off

1. Short-press the power button when the microphone is in the power off state to power on, microphone A LED ring lights blue, microphone B
   LED ring lights are white. Long-press the power button for 3 seconds when the microphone is in power on statę to power off, microphone LED ring turns off.

2. Plug the receiver to car USB port via the data cable, and turn on your car, and the receiver is powered on automatically. The receiver turns off when the data cable is unplugged. The receiver keeps the same on/off state via car on/off state when it is connected to the car.

3. The microphone turns off automatically with no input signal for over 10 minutes.

Connect a microphone to your car

1. Connect the data cable type-C to the receiver, then plug the data cable USB into the car. Turn on your car, the receiver’s green LED flashes slowly when no microphone is turned on and connected. Turn on your microphone, the receiver searches and connects to the microphone automatically, and the receiver LED lights green.
2. Connect your receiver, turn on your car, power on your microphone, and then click and play KTV software in your car play, you are able to hear your voice from your car speakers when you talk, it’s time to Karaoke.
   Note: Two microphones have different LED colors. Microphone A lights in blue while microphone B lights in white.

Pair
Turn off your microphone, and long-presS the power button over 7 seconds until you see the LED Lighting rotates, which indicates the microphone has successfully paired to the receiver, You should be able to hear your voice from the car speaker when you talk via your microphone.
Short-press the microphone power button to exit the pairing process.

Note

1. The microphone has beeń paired to your receiver when it is shipped. You only need to pair when the microphone is not able to Connect with your receiver automatically or being interfered by another signal.
2. Lift is paired successfully, the LED ring rotates all the time before you exit the pair procesS via short-presș the power button.

Pair operation

1. Keep your microphone dose enough to your receiver within 0.5m, with no obstruction between the microphone and the receiver.
2. Turn off your microphone, and long-press power button Over 7 seconds, talk to your microphone until you can hear your voice from your car speakers, and release the power button.
3. Short-press the power button to exit the pair operation.

LED

Note: The illustrations of products, accessories, user interfaces and other illustrations in the manual are schematic diagrams and are for reference only; Due to product updates and upgrades, the actual product may be slightly different, please refer to the actual product.

Power button functions

Specification

FCC

This device complies with part 15 of the FCC Rules. Operation is subject to the following two conditions: (1) This device may not cause harmful interference, and (2) the UNIS device must accept any interference received,including interference that may cause undesired operation.
Any changes or modifications not expressly approved by the party responsible for compliance could void the user’s authority to operate the equipment.

Note: This equipment has been tested and found to comply with the limits for Class B digital devices, pursuant to part 15 of the FCC Rules.
These limits are designed to provide reasonable protection against harmtul interterence in a residential installation. This equipment generates uses and can radiate radio frequency energy and, if not installed and used in accordance! with the instructions, may cause harmful interterence to radio communications. However, there is no guarantee that interference will not occur in a particular installation. If this equipment does cause harmful interference to radio or television reception, which can be determined by turning the equipment off and on, the user is encouraged to try to correct the interference by one or more of the following measures:

• Reorient or relocate the receiving antenna.
• Increase the separation between the equipment and the receiver.
• Connect the equipment to an outlet on a circuit different from that to which the receiver is connected.
• Consult the dealer or an experienced radio/TV technician for help.

Product model Product identifier

IC Caution

This device complies with Industry Canada licence-exempt RSS standard(s).
Operation is subject to the following two conditions: (1) This device may not cause interference, and (2) This device must accept any interference, including interference that may cause undesired operation of the device.

RF warning for Portable devices:

The device has been evaluated to meet the general RE exposure requirement. The device can be used in portable exposure conditions without restriction.
This device operates on a no-interference, no-protection basis. Should the user seek to obtain protection from other radio services operating in the same TV bands, a radio license is required. For further details, consult Innovation, Science and Economic Development Canada’s s Client Procedures Circular CPC-2-1-28, Voluntary Licensing of Licence-Exempt Wireless Microphónes in the TV Bands.

Manufacture: Beijing Thunderstone Technology Co., LTD
Address: 3rd Floor of Building 8, Tianchang Garden, Media Village, Beiyuan North Road, Chaoyang District, Beijing, China
FC
FCC ID : 2A8SC-TSL42
IC: 29359-TSL42

Read User Manual Online (PDF format)

Read User Manual Online (PDF format)  >>

Download This Manual (PDF format)

Download this manual  >>