COMPAL AAN1F-NC8 Cedar User Manual

: July 11, 2024
: COMPAL

Table of Contents

COMPAL AAN1F-NC8 Cedar
Specifications
Product Usage Instructions
FAQ
Overview
Application Interface (HW/Ant/SW)
ME Mechanical Specification
Application Block diagram
Wall Mount Bracket Installation Manual
FCC STATEMENT
Read User Manual Online (PDF format)
Download This Manual (PDF format)

COMPAL AAN1F-NC8 Cedar

Specifications

AIO – CU/DU/RU 3GPP Standard RAT Mode Platform SU-MIMO
Modulation: DL: 4 layers, UL: 2 layers (4T2R); DL: QPSK/16QAM/64QAM/256QAM, UL: QPSK/16QAM/64QAM
Interface: Copper(RJ45) x1, Optical (SFP+) x1
Capacity: 64 active UEs
Throughput: DL 1.2 Gbps (7DS2U); UL: 400 Mbps (DSUU)
Duplex mode: TDD (7D1S2U, DSUU, SUDS)
Frequency band: N48 100MHz
Bandwidth: Maximum 4T4R, Internal
Antenna: 250mW (24dBm) per channel
Dimensions: 310 x 265 x 95 mm
Weight: 5 kg
Power supply: 12V DC adaptor (85~264VAC input)

Product Usage Instructions

Installation and Setup

Follow the provided Wall Mount Bracket Installation Manual for mounting the device securely on Masonry Walls or Cement Walls.

Connection

Connect the device using the provided interfaces:

SFP+ Fiber for Datalink
RJ45 for management port/Debug use
12V Adapter Connector for power supply

Application

The device is primarily used for small-cell 5G applications. It
connects to a 5GC Server to provide networking for 5G signals.

Maintenance

Regularly check the device for any dust accumulation and ensure proper ventilation to prevent overheating.

FAQ

Q: What should I do if the device is not powering on?
A : Check the power supply connection and ensure that the input voltage is within the specified range (85~264VAC).
Q : How can I troubleshoot connectivity issues?
A : Verify the cable connections, reset the device, and check for any configuration errors in the network settings.

Connect Your Talent

COMPAL-AAN1F-NC8-Cedar-fig-1

Overview

Introduction
A small Cell (Cedar) is an Integrated small Cell, and it includes CU/DU/RU.

Specification

AIO – CU/DU/RU

UL: QPSK/16QAM/64QAM

Application Interface (HW/Ant/SW)

COMPAL-AAN1F-NC8-Cedar-fig-2

ME Mechanical Specification

Configuration

COMPAL-AAN1F-NC8-Cedar-fig-3

Packing Mechanical Specification

Packing Structure

Step 1
Wrapped the device with foam, then placed it well into the EPE.
Step 2
Put the accessories in the right place.
Step 3
Put the EPE with the device in the carton first.
Step 4
Then put the EPE with accessories on the top of the carton.
Step 5
H-sealing.

Application Block diagram

The device is used for small cell 5G application as below as

Application Description

Use small cell to connect 5GC Server and provide networking for 5G signal
Small Cell is adapter 4T4R structure and RF power is 250mW/per path.
RJ451 or SFP+1 for Data link;
RJ45*1 for management port/Debug use.

COMPAL-AAN1F-NC8-Cedar-fig-7

Wall Mount Bracket Installation Manual

Materials

Masonry Walls or Cement Walls
6- Drill holes in the wall.

Step. 2 Insert plastic anchors into the holes in the wall.
Step. 3 Insert Screw-B through Bracket-B into plastic anchors.
Step. 4 Put the Bracket-A on the device and fixed by four screws.

Note: Assuming I/O ports facing down.

Step. 5 Put Bracket-A into bracket-B two slide rails from top to bottom

FCC STATEMENT

Legal Information

Warning Statement

This device complies with part 15 of the FCC Rules. Operation is subject to the following two conditions:

This device may not cause harmful interference
This device must accept any interference received, including interference that may cause undesired operation.

Changes or modifications not expressly approved by the party responsible for compliance could void the user‘s authority to operate the equipment.
This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation. This equipment generates, uses, and can radiate radio frequency energy and, if not installed and used in accordance with the instructions, may cause harmful interference to radio communications. However, there is no guarantee that interference will not occur in a particular installation. If this equipment does cause harmful interference to radio or television reception, which can be determined by turning the equipment off and on, the user is encouraged to try to correct the interference by one or more of the following measures:

Reorient or relocate the receiving antenna
Increase the separation between the equipment and the receiver.
Connect the equipment to an outlet on a circuit different from that to which the receiver is connected.
Consult the dealer or an experienced radio/TV technician for help.

This device has been tested and meets applicable limits for Radio Frequency (RF) exposure. This equipment should be installed and operated with a minimum distance 20cm between the radio & your body.

RF Exposure Information

This device has been tested and meets applicable limits for Radio Frequency (RF) exposure. This equipment should be installed and operated to ensure a minimum of 20 cm spacing to any person at all times.