Link 2 Home EM-1001 Wireless Remote Control Electrical Installation Guide
- July 9, 2024
- Link 2 Home
Table of Contents
Link 2 Home EM-1001 Wireless Remote Control Electrical
Wireless Remote Control Outlets – 2 Transmitters & 5 Receivers
INSTRUCTION MANUAL
CATALOG NUMBERS
EM-1001
Thank you for choosing Link2Home!
PLEASE READ BEFORE RETURNING THIS PRODUCT FOR ANY REASON.
If you have a question or experience a problem with your Link2Home purchase,
go to http://www.link2home.com
If you can’t find the answer or do not have access to the internet, call
1-888-783-6082 from 9 a.m. to 5 p.m.
EST Mon.-Fri. to speak with an agent. Please have the catalog number available
when you call.
SAVE THIS MANUAL FOR FUTURE REFERENCE
Important Safety Guidelines
SAVE THESE INSTRUCTIONS FOR FUTURE REFERENCE.
Definitions: Safety Alert Symbols and Words
This instruction manual uses the following safety alert symbols and words to
alert you to hazardous situations and your risk of personal injury or property
damage.
-
DANGER: Indicates an imminently hazardous situation which, if not avoided, will result in death or serious injury.
-
WARNING: Indicates a potentially hazardous situation which, if not avoided, could result in death or serious injury.
-
CAUTION: Indicates a potentially hazardous situation which, if not avoided, may result in minor or moderate injury.
(Used without word) Indicates a safety related message. -
NOTICE: Indicates a practice not related to personal injury which, if not avoided, may result in property damage.
-
WARNING: PLEASE READ THIS INSTRUCTION MANUAL THOROUGHLY AND COMPLETELY BEFORE INSTALLATION & USE. FAILURE TO DO SO COULD CAUSE DAMAGE TO PROPERTY, SERIOUS INJURY OR DEATH, AND VOID YOUR WARRANTY.
-
WARNING: Cancer and Reproductive Harmwww.
P65Warnings.ca.gov. -
AVERTISSEMENT: Cancer et Troubles de l’appareil reproducteurwww.
P65Warnings.ca.gov. -
ADVERTENCIA: C6ncery Dano Reproductivowww.
P65Warnings.ca.gov.
Wireless Remote Control Outlets – 2 Transmitters & 5 Receivers
WARNING: Danger of explosion if battery is incorrectly replaced. When replacing battery, replace it with the same or equivalent type CR2032. Observe correct polarity(+ and-) when replacing batteries. Do not store or carry batteries so that metal objects can contact exposed battery terminals.
DANGER: DO NOT INGEST BATTERY; CHEMICAL BURN HAZARD. This product
contains
a coin/button cell battery. If the coin/button cell battery is swallowed, it
can cause severe internal burns in just 2 hours and can lead to death.
Keep new and used batteries away from children. If the battery compartment
does not close securely, stop using the product and keep it away From
children.
If you think batteries might have been swallowed or placed inside any part of
the body, seek immediate medical attention.
-
Step A: Locate the battery compartment on the back of the remote.
Push down and away to slide the compartment cover off.
Step B: Remove the plastic battery tab from the battery compartment in the back of the remote control to activate the pre-installed battery.
Step C: Slide the compartment cover on the remote and click securely into place. Your remote is now ready to use . -
Plug the receiver into a standard AC electrical wall socket.
Plug the appliance into the receiver outlet. -
While the outlet is plugged into the wall, hold down the square button on the left side of the outlet For
3- 7 seconds or until you see it start to Flash. Once you see Flashing, press the ON or OFF button for numbers 1, 2, 3, 4, or 5 to have it be assigned to that number. When you see that the appliance can be turned on or off by using the remote, the outlet and remote have been paired successfully.
Specifications
- Power input: 125V /60Hz
- Power output: 1875W/15A (Max.)
- Transmitter frequency: 433.92MHz
- Remote transmitter battery: DC CR2032, 3V battery 1 pc Transmission range: up to 100ft
Wireless Remote Control Outlets – 2 Transmitters & 5 Receivers
Remote Battery Replacement:
If operation of the receiver units becomes erratic, it may be necessary to
replace the battery in the hand-held remote unit. To do this, first remove the
battery compartment cover. Press the tray release button on the back of the
remote. Next, remove the depleted battery and discard according to local
ordinances. Be sure to correctly install the new battery. Replace battery
compartment cover and test by using it to control the indoor remote control
outlets.
CAUTION
- Appliances to be connected to the remote control socket MUST NOT exceed the voltage and current ratings as in “Specifications”.
- Operation is subject to the following two conditions:
- this appliance may not cause harmful interference,
- this appliance must accept any interference received, including interference that may cause undesired operation.
- Only for indoor use and storage.
- Low transmitter battery may lower the distance between the transmitter and the receiver.
Wireless Remote Control Outlets – 2 Transmitters & 5 Receivers
Grounding Instructions
In the event of malfunction or breakdown, grounding provides a path of least
resistance for electric current to reduce the risk of electric shock. The
remote control outlet must be connected to a cord having an equipment-
grounding conductor and a grounding plug. The plug must be plugged into an
appropriate outlet that is properly installed and grounded in accordance with
all local codes and ordinances.
DANGER:
- Improper connection of the equipment grounding conductor can result in a risk of electric shock. The conductor with insulation having an outer surface that is green with or without yellow stripes is the equipment grounding conductor. If repair or replacement of the cord or plug is necessary, do not connect the equipment-grounding conductor to a live terminal. Check with a qualified electrician or service person if the grounding instructions are not completely understood, or if in doubt as to whether the remote control outlet is properly grounded. Do not modify the plug connected to the remote control outlet- if it will not fit the outlet, have a proper outlet installed by a qualified electrician.
- FOR GROUNDED, CORD-CONNECTED REMOTE CONTROL OUTLET RATED LESS THAN 1 SA AND INTENDED FOR USE ON A NOMINAL 125V SUPPLY CIRCUIT
- The remote control outlet is for use on a nominal 125V circuit, and should be connected to a grounding outlet that looks like that illustrated in sketch a. A temporary adaptor, which looks like the adaptor illustrated in sketch b, may be used to connect this plug to a 2-pole receptacle as shown in sketch b if a properly grounded outlet is not available. The temporary adaptor should be used only until a properly grounded outlet can be installed by a qualified electrician. The green colored rigid ear, lug, and the like, extending from the adaptor must be connected to a permanent ground such as a properly grounded outlet box cover. Whenever the adaptor is used, it must be held in place by the metal screw.
NOTE: IN CANADA, THE USE OF A TEMPORARY ADAPTOR IS NOT PERMITTED BY THE CANADIAN ELECTRICAL CODE. Ensure that remote control outlet is connected to an outlet having the same configuration as the plug.
1 YEAR LIMITED WARRANTY
- IMPORTANT: Proof of Purchase is required to obtain warranty service
- Paragon Group USA Inc. warrants to the original owner that our products will be free from defect in workmanship and material for a period of ONE YEAR from the date of purchase. Should any unit(s) prove to be defective during this period, Paragon Group USA Inc. will be responsible for replacement of the defective unit(s) only. Paragon Group USA Inc. is not responsible for labor charges or any incidental or consequential expenses.
- Not Covered – Batteries are not covered by this warranty. Repair service, adjustment and calibration due to misuse, abuse or negligence are not covered by this warranty.
- Unauthorized service or modification to this product or of any furnished components will void this warranty in its entirety. This warranty does not include reimbursement for inconvenience, installation, set-up time, loss of use, postage, unauthorized service, or other products used in conjunction with Link2Home products.
- For warranty service, please contact Paragon Group USA Inc.
- Customer Service by Phone: 1-888-783-6082 or e-mail: info@paragongroupusa.com.
- This warranty gives you specific legal rights, and you may also have other rights which vary from state to state.
Paragon Group USA Inc.
Link2Home Product Division
Englewood, NJ 07631
USA
Read User Manual Online (PDF format)
Read User Manual Online (PDF format) >>