JX ROBOT S5C Handheld 3 Axis Gimbal Stabilizer User Manual

JX ROBOT S5C Handheld 3 Axis Gimbal Stabilizer

Quick start (Don’t power on)

1. Remove the smartphone case before installing, and put the smartphone on the phone holder according to the sticker(as below picture shows), make it is at the middle of the holder.
2. Put the smartphone in the phone holder, and let it resist the motor as the below picture shows, to avoid vibration while working.
3. Loosen the balance knob, and adjust the balance arm until the smartphone in nearly balance condition.

Power On/Off

Power on
Press the power button until the indicators are on.

Power off
Press the power button until the indicators are off.

Bluetooth connected by native camera

Power on the gimbal, turn on the Bluetooth on the phone, enter the smartphone Bluetooth setting page, and choose the device name “GP5-xxxx” to connect. After connecting to the Bluetooth, press the shutter button on a gimbal to take a picture or start & stop video recording.

Instructions for four modes

All Follow(AF): The Roll axis is locked, the Pan (left/right) and Tilt(up/down) axes will follow the handle movement.

• Default mode upon powering on

Half Follow(HF): Tilt & Roll axes are locked. Pan axis rotates left/right smoothly with the handle movement.

Lock Full(LF): Pan,Tilt, Roll axis are all locked. The camera remains still and stable, which means the camera cannot follow the movement of the handle

First person view(FPV)： Pan, Tilt, Roll axis follow the movement of the handle

Other Working Mode Phone Go
Long press the shutter button until the AF light is flashing, gimbal enters Phone Go mode, release the shutter button, gimbal will exist in Phone Go mode.

Gimbal Overview

1. Mobblie Phone Holder
2. Handle
3. Pitch Motor
4. Adjustable Arm
5. Pan Motor
6. Mode indicator
7. Battery indicator
8. Power Button
9. Joystick
10. Mode switch button
11. Tigger Button
12. Zooming Wheel
13. Micro USB
14. Roll Motor
15. Rope hanging hole

Horizontal & Vertical Switch

(Three switching ways) Way 1

1. Put the gimbal as the below picture shows
2. Press the mode button 3 times, and switch from horizontal mode to vertical mode;
3. Press the mode button three times again, and switch from vertical back to horizontal mode;
   • Reminder: FPV mode doesn’t support this operation.
   • Way 2 : Rotate the smartphone clamp Grasp the holder and rotate the holder directly with 90°.
   • Way 3: Gesture switch
   1. Hold the gimbal perpendicular to the ground;
   2. Tilt the gimbal left or right at 70°;
   3. The gimbal will go to vertical mode automatically;
   4. The gimbal will back to the horizontal model automatically when the gimbal is upright;
      Reminder: FPV mode doesn’t support this operation.

Charging

About APP

This product supports a native camera and can do basic stable shooting without APP with the native camera. If you want to use more functions (such as zoom, tracking, panoramic and time-lapse), need to download the app.

Download the Gimbal Pro APP
Scan the QR code or search “Gimbal pro2” on the Google play store or “Gimbal pro” on the App store.

• Gimbal Pro requires an iOS 12.0 system and later or an Android 8.0 system and later

Connect to the Gimbal Pro APP

1. Go to the settings page on the smartphone
2. Go to Bluetooth setting, find and click the device name “GP5_xxxx” to pair, app will work after connect successfully.

APP interface overview: App

1. Video/Photo mode
2. Shooting function select
3. Shoot button
4. Front/Rear camera switch
5. Album
6. Bluetooth icon
7. Face/object tracking
8. Gimbal condition display
9. Gimbal power display
10. Phone power display
11. Flash
12. Home page
13. Camera parameters
14. Gimbal mode adjust
15. Settings

Specification

• Gimbal Dimension
  

  • 112 70 289mm

• Net Weight
  

  • 473g

• Payload
  

  • 280g

• Compatible smartphone range
  

  • width: 55-90mm
  • diagonal: no more than 192mm/7.72inch;
  • thickness: 7-12mm

• Tilt Angle
  

  • 330°

• Roll Angle
  

  • 160°

• Pan Angle
  

  • 360°

• Controllable Tilt Angle
  

  • +75°/-245°

• Controllable Roll Angle
  

  • +80°/-80°

• Controllable Pan Angle
  

  • +360°/-360°

• Working temperature
  

  • 0℃~40℃

• Working Voltage
  

  • 3.4~4.2V(Standard 3.7V)

• Working Currency
  

  • 150~3000mA (Standard 1500mA)

• Input Voltage
  

  • 5V

• Input Currency
  

  • 1A

• Charging Time
  

  • 210mins

• Working Time
  

  • 500mins

• Standby Time:

  • 1560mins

Caution

1. Ensure the motor rotation is not blocked by an external force during and after the stabilizer is powered on;
2. Please do not contact with seawater or corrosive liquid;
3. Please do not disassemble the stabilizer (except for the detachable accessories in the manual);
4. If the motor works continuously for a long time, the surface temperature of the motor may be too high.
5. It is strictly forbidden to drop or collide with the stabilizer, which may damage it and cause abnormal operation;

Storage and maintenance

1. Please keep this product away from children and pets;
2. It is forbidden to put the product near the heat source(furnace or heater, etc.) and in the car at hot weather;
3. Please store the product in a dry environment;
4. Do not overcharge or discharge the battery, otherwise, the battery cell will be damaged;
5. Do not use the product in the environment with too high or too low temperature;

FCC Warning Statement

Changes or modifications not expressly approved by the party responsible for compliance could void the userʼs authority to operate the equipment. This equipment has been tested and found to comply with the limits for a Class B digital device, under Part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation. This equipment generates uses and can radiate radio frequency energy and, if not installed and used under the instructions, may cause harmful interference to radio communications. However, there is no guarantee that interference will not occur in a particular installation. If this equipment does cause harmful interference to radio or television reception, which can be determined by turning the equipment off and on, the user is encouraged to try to correct the interference by one or more of the following measures:

• Reorient or relocate the receiving antenna.
• Increase the separation between the equipment and the receiver.
• Connect the equipment to an outlet on a circuit different from that to which the receiver is connected.
• Consult the dealer or an experienced radio/TV technician for help.

FCC Radiation Exposure Statement
The device has been evaluated to meet general RF exposure requirements. The device can be used in portable exposure conditions without restriction. This device complies with Part 15 of the FCC Rules. Operation is subject to the following two conditions: (1)This device may not cause harmful interference, and (2)This device must accept any interference received, including interference that may cause undesired operation.

Read User Manual Online (PDF format)

Download This Manual (PDF format)

Download this manual  >>