STEELGREEN MANUFACTURING SG46 Independent Sprayer Instruction Manual
- June 13, 2024
- STEELGREEN MANUFACTURING
Table of Contents
INSTRUCTION MANUAL
7 GAL. INDEPENDENT SPRAYER
Models: SG46, & SG52
7 GAL. INDEPENDENT SPRAYER EXPLODED VIEW ,LEFT SIDE
7 GAL. INDEPENDENT SPRAYER EXPLODED VIEW, LEFT SIDE
PARTS UST
ITEM| QTY| PART NUMBER| DESCRIPTION
1| 1| 554000| PUMP, SHURFLO
2| 1| 554120| HEAT SINK, SPRAY PUMP
3| 2| S54103| PUMP FITTING, BARB, ELBOW, 1/2 X 1/2
4| 2| S51242| BULKHEAD FITTING, TANK
5| 1| 551270| SPRAY FILTER
6| 1| S52063| 3/4 X 3/4 ST
7| 1| S52028| ELBOW, 3/4 X 1/2 BARB
8| 1| 551283| VALVE, THROTTLING
9| 1| 552000| TEE, PIPE, 3/4 WITH GAUGE PORT
10| 1| M10007-L-IND| TANK, 7 GALLON
11| 1| S51243| CAP, TANK
12| 4| CB-51634| CARRIAGE BOLT, SS – 5/16-18 x 3/4
13| 4| HFNCS-516S| HEX FLANGE NUT, SS – 5/16-18
14| 4| TRPC-141S| PHILLIPS SCREW, SS – 1/4-20 x 1
15| 4| SSNNC-14| NYLOCK, SS – 1/4-20
16| 4| HFSSC-3875| HEX BOLT, 3/8 X 3/4
17| 1| S51234-D| PRESSURE GAUGE, 60 PSI
18| 1| R21-113| ANTI VORTEX PLATE
19| 1| 553019| HOSE,COIL
20| 1| S51260| HANDLE, SPRAY
21| 1| 552041| 90 ELBOW, 3/4 MNPT X 3/4 FNPT
22| 4| MS4| HOSE CLAMP, 3/8
23| 1| S51261| NOZZLE, SPRAY
24| 1| 552013| 1/2 MNPT X 1/2 HOSE BARB
25| 1| 552064| 3/4 X 1/2 REDUCER
26| 1| S52040| 1/2″ 90° Street Elbow
27| 1| 552050| 1/2 X 1/4
28| 1| W22-183| TANK SUPPORT, 7 GAL. SG46/52
7 GAL. INDEPENDENT SPRAYER EXPLODED VIEW, RIGHT SIDE
7 GAL. INDEPENDENT SPRAYER EXPLODED VIEW, RIGHT SIDE
PARTS LIST
ITEM| QTY| PART NUMBER| DESCRIPTION
1| 1| S54000| PUMP, SHURFLO
2| 1| 554120| HEAT SINK
3| 2| S54103| ELBOW FITTING 90DEG. BARB
4| 2| 551242| TANK BULKHEAD FITTING
5| 1| S51270| SPRAY FILTER
6| 1| 552064| 3/4 X 1/2 REDUCER
7| 1| 552028| 90DEG. .5008 .750T
8| 1| 551283| REGULATER
9| 1| S52000| PIPE TEE
10| 1| 552013| 1/2 MNPT X 1/2 HOSE BARB
11| 1| M1007| M1007-R-IND
12| 1| 552050| 1/2 X 1/4
13| 1| 551243| TANK CAP
14| 4| CB-51634| CARRIAGE BOLT, SS – 5/16-18 x 3/4
15| 4| HFNCS-5165| HEX FLANGE NUT, SS – 5/16-18
16| 4| TRPC-141S| PHILLIPS SCREW, SS – 1/4-20 x 1
17| 4| SSNNC-14| NYLOCK, SS – 1/4-20
18| 4| HFSSC-3875| HEX BOLT, 3/8 X 3/4
19| 1| S51234-0| PRESSURE GAUGE, 60 PSI
20| 1| R21-113| ANTI VORTEX PLATE
21| 1| S52040| 1/2″ 90° Street Elbow
22| 1| S53019| HOSE,COIL
23| 1| 551260| HANDLE, SPRAY
24| 1| 551261| NOZZLE, SPRAY
25| 4| MS4| HOSE CLAMP, 3/8
26| 1| 552063| 3/4″ X 3/4″ ST.
27| 1| S52041| PIPE ELBOW 90 DEG.
28| 1| W22-183| TANK SUPPORT, 7 GAL. 5G46/52
STEP ONE: Disconnect the battery, ground first and then power wire.
NOTE: Steps 2 & 3 instructions are the same for the right and left side,
if both left & right side tanks are being installed.
STEP TWO: Remove existing storage container and support bracket from the
frame.
STEP THREE: Install the independent sprayer to the frame as shown.
STEP FOUR : Connect the “pump” wiring harness to the pump plug and route the harness between thetank and upright.
STEP FIVE : Route the “pump” wiring harness along the frame and upright to the control panel.
STEP SIX: Remove the plastic cap from “Aux 1” in the panel and route the switch connector of the “pump” wiring harness through the hole in the panel.
STEP SEVEN: Connect the “pump” wiring harness to the “20A” side of the rocker switch.
STEP EIGHT: Connect the ground wire from the “pump” wiring harness to the up right cross member.
STEP NINE: Connect the “pump power” wiring harness to the other side of the rocker switch.
STEP TEN: Install the rocker switch in the control panel and route the “pump power” wiring harness down the up right, along the frame to the battery.
STEP ELEVEN : Reconnect the battery, power wire first along with the pump power wire from the wiring harness, and then reconnect the ground wire.
STEP TWELVE : Once both harnesses are routed and connected, securely fasten them to the frame and existing harnesses in the up right with zip ties.
MANUAL
PART NO.| MANUAL
REV.| DESCRIPTION| KIT
PART NO.
---|---|---|---
SGM-012| B| SG46-52 7 GALLON INDEPENDENT SPRAYER| P10030-1
Steel Green Mfg.
824 S State Road 39
Lebanon, IN 46052
(765)-481-2890
www.steelgreenmfg.com