Skyfan SKY Series DC Ceiling Fan Instruction Manual

Skyfan SKY Series DC Ceiling Fan

Product Information

• Specifications
  • Model: SKY903WH, SKY903WH-L, SKY903BL, SKY903BL-L
  • Intelligent energy saving DC technology
  • With LED (-L) model

Product Usage Instructions

• Before Installation
  • Unpack the fan carefully and identify all parts as shown in Fig 1a and Fig 1b.
• Safety Precautions
  • For safe use of this fan, follow these precautions:
  • The appliance is not intended for use by persons with reduced physical, sensory, or mental capabilities.
  • Children should be supervised to ensure safe use of the appliance.
  • Ensure proper installation by a licensed electrician.
  • Do not modify the fan as it may affect performance and safety.

FAQs

• Q: Can I install the fan myself?
  • A: The fan must be installed by a licensed electrician to ensure safety and proper function.
• Q: Are the LED models energy-efficient?
  • A: Yes, the LED models feature intelligent energy-saving DC technology for efficient operation.

Images are for reference only and may vary slightly from the actual product. Ceiling Fan Installation Manual Rev 1.8

MODELS

• SKY903WH, SKY903WH-L, SKY903BL, SKY903BL-L
• SKY1203WH, SKY1203WH-L, SKY1203BL, SKY1203BL-L
• SKY1303WH, SKY1303WH-L, SKY1303BL, SKY1303BL-L, SKY1303TK, SKY1303TK-L
• SKY1503WH, SKY1503WH-L, SKY1503BL, SKY1503BL-L, SKY1503TK, SKY1503TK-L
• SKY1204WH, SKY1204WH-L, SKY1204BL, SKY1204BL-L
• SKY1404WH, SKY1404WH-L, SKY1404BL, SKY1404BL-L

Thank you for purchasing this quality Ventair DC ceiling fan. To ensure correct function and safety, please read all instructions before using the product and keep all instructions for future reference.

CAUTION Read Instructions Carefully For Safe Installation and Fan Operation MUST BE INSTALLED BY A LICENSED ELECTRICIAN

SAFETY PRECAUTIONS

WARNING:

• FOR SAFE USE OF THIS FAN. AN ALL-POLE DISCONNECTION MUST BE INCORPORATED INTO THE FIXED WIRING INACCORDANCE WITH THE WIRING RULES.
• As outlined in clause 7.12.2 of AS/NZS 60335-1 for meeting the minimum electrical safety of this standard.
• Please note warranty will be void if installation is without an all-pole disconnection incorporated in the fixed wiring by the wiring rules.
• Example: If a fan is connected to a circuit that can be isolated via an all-pole safety switch at the switchboard, then this is considered to be an all-pole disconnection to the ceiling fan electrical circuit, meeting the requirements of clause 7.12.2 of AS/NZS 60335.1.
• A single-pole switch on the active of receiver input of the remote control must also be included in the wiring, and located in the same room as the ceiling fan.(see wiring diagram

1. The appliance is not intended for use by persons (including children) with reduced physical, sensory or mental capabilities, or lack of experience and knowledge unless they have been given supervision or instruction concerning the use of the appliance by a person responsible for their safety.
2. Children should be supervised to ensure that they do not play with the appliance. The structure to which the fan is to be mounted must be capable of supporting a weight of 20kg.
3. The fixing point on the ceiling requires a solid bracing structure such as Timber noggins or joists. The bracing should be butted up firmly and securely to the back of any nonstructural roofing panel such as plaster or Gyprock to ensure safety and optimum performance of the fan.
4. The fan should be mounted so that the blades are at least 2. 1m above the floor.
5. Only a licensed electrician should complete the installation.
6. WARNING: If unusual wobbling or oscillating movement is observed, immediately stop using the ceiling fan and contact the manufacturer, its service agent, or suitably qualified persons.
7. WARNING: Light and fan must be connected to the same phase. Before servicing, ensure both light and fan circuits are disconnected.

Do not dispose of electrical appliances as unsorted municipal waste, use separate collection facilities. Contact your local government for information regarding the collection systems available. If electrical applicances are disposed of in landfills or dumps, hazardous substances can leak into the groundwater and get into the food chain, damaging your health and well-being.

BEFORE INSTALLATION

Unpack the fan carefully and identify all parts. Please refer to Fig 1a and Fig 1b.

Skyfan and Skyfan 4 WITHOUT LIGHT

1. Mounting bracket x 1
2. Pre-assembled fan motor, down rod, canopy and bottom cover x 1
3. Blades x 3 (or 4)
4. Remote Control x 1 (2 pcs R03 1.5V AAA Batteries included. Wood screws 3.5x20mm)
5. Receiver x 1
6. Balancing Kit x 1
7. Blade screws x 6 (or 8) (5 x 16mm)
8. Wood screws for mounting bracket x 2 (6 x 50mm)  Wood screw for safety wire x 1  (6 x 50mm)

Skyfan and Skyfan 4 WITH LIGHT

1. Mounting bracket x 1
2. Pre-assembled fan motor, down rod, canopy and LED light x 1
3. Blades x 3 (or 4)
4. Remote Control x 1 (2 pcs R03 1.5V AAA Batteries included. Wood screws 3.5x 20mm).
5. Receiver x 1
6. Balancing Kit x 1
7. Blade screws x 6 (or 8) (5 x 16mm)
8. Wood screws for mounting bracket x 2 (6 x 50mm) Wood screw for safety wire x 1  (6 x 50mm)

Please note: Check for any damage to the fan prior to installation. Physical damage such as marks and scratches is not covered by the in home warranty. In this case, please contact Ventair to discuss replacement parts.

MOUNTING BRACKET

• The ceiling fan must be installed in a location so that the blades have a minimum 300mm spacing from the tip of the blade to the nearest objects or walls.
• Secure the hanging bracket to the ceiling joist or structure that is capable of carrying a load of at least 20kg, with the two Fixing screws provided. Ensure at least 30mm of the screw is threaded into the support structure.

PLEASE NOTE:

• The bracket fixing screws provided are for use with the wooden structures only. These screws are designed specifically for this purpose, and use of other types of screws, ie: Bugle-headed screws may void the warranty.
• For structures other than wood, the appropriate screw type MUST be used.

QUICK ‘CLICK’ BLADE INSTALLATION

BLADE ATTACHMENT

1. Insert the blades (Skyfan x 3, Skyfan 4 x 4) into the blade holding slots on the motor housing, slide downward, and click into position.
2. Insert the 2 safety screws, being careful not to over-tighten.
3. Move motor housing canopy downward until covering the motor.

HANGING THE FAN

• Lift the fan assembly onto the mounting bracket. Ensure that slot (A) of the hanger ball is fully aligned/engaged with Tab (B) of the mounting bracket (C) to prevent the fan from rotating when in operation. Fig. 3)

ANGLED CEILING INSTALLATION

This fan-hanging system supports a maximum 15-degree angled installation. (Fig 4)
Please note: Tab (B) on the hanging bracket that sits in the groove (A) on the hanging ball should be positioned at the highest point to ensure correct operation.

FINISHING THE INSTALLATION

• Complete the electrical connection at the mounting bracket terminal block. Fix the EARTH cable from the motor to the mounting bracket.
• NOTE: Skyfan DC is a Class I electrical product. (Refer to Fig 6.).
• Connect the fan to the receiver (this can be done before or after sliding the receiver into place).
  • A. For fan models without light, plug the cable marked ‘motor’ into the remote control box. See Fig 7.2
  • B. For fan models with light, plug cable marked ‘motor’ and ‘LED’ into the remote control box. See Fig 7.1
• Slide the receiver into position in the hanging bracket making sure the AC input connecter on the receiver is aligned with the AC port on the receiver. Refer to Fig 7.1 on page 7
• Slide the canopy upwards into position over the mounting bracket then turn counterclockwise to twist lock into position. Ensure all 4 tabs on the mount bracket are located correctly into the slots on the canopy. The canopy should be sitting approx. -3mm off the ceiling.
• Ensure all wires are tucked neatly into the canopy taking care not to cause damage.

ELECTRICAL WIRING DIAGRAM

• WARNING: FOR YOUR SAFETY ALL ELECTRICAL CONNECTIONS MUST BE UNDERTAKEN BY
• A LICENSED ELECTRICIAN PER/NZS 3000 WIRING RULES.
• Connect the “LIVE” supply to the “ ” of the terminal block on the mounting bracket.
• Connect the “EARTH” supply wire to (the terminal block on the mounting bracket.
• Connect the “NEUTRAL” supply to the “ ” of the terminal block on the mounting bracket.
• Screw the “EARTH” cable from the motor to the cavity Please refer to Fig 6. on the mounting bracket.

REMOTE CONTROL OPERATION

• * Turn the wall switch to ‘ON’ The Fan is now in standby mode. A ‘beep’ will be heard. If your fan has a light, the light will illuminate in the default setting of 100% brightness in (NW)  Natural white light. ![Skyfan-SKY-Series-DC-Ceiling-Fan-FIG-1 \(13\)](https://manuals.plus/wp-content/uploads/2024/07/Skyfan-SKY-Series-DC-Ceiling-Fan-FIG-1-13.png)

Fan Models With Light

• Note: Light will reactivate at the previous brightness and colour (CCT) settings when using the handset only. Once the wall  (isolation) switch has been turned ‘OFF’ Light will default back to 100% brightness (NW) Natural white light.

A remote control consists of two parts.

1. Handset (transmitter) controller.
2. Receiver. Receives messages from the handset and is located in upper canopy of the fan.
   • The Skyfan DC remote control comes pre-paired at the factory and is ready to use. Pairing will only be required in the situations mentioned below.

Using 1 remote handset to control 2 or more Skyfan DC Ceiling fans

• Choose the fan you wish to pair with your handset.
• Turn isolation switch ‘ON’ and within 20 seconds press and hold on the remote for 3 seconds. The fan will emit a ‘beep beep’ sound to indicate the pairing process is activated.
• Press and change the speed of the ceiling fan via the remote to check the operation and successful pairing.

Troubleshooting – Skyfan DC

• Q) One remote is controlling multiple fans, how do I fix this?
  • A) This can be fixed by re-pairing each fan one at a time:
  • Turn all fans you wish to separate off at the isolation switch and leave off for a minimum of 1 minute.
  • Turn the isolation switch on for the 1st fan and within 20 seconds press and hold on the remote for 3 seconds. Remote should be paired, check fan functions.
  • Repeat the above steps with next fan ensuring the previous fan is left on at the isolation switch.
  • NOTE: Each fan must have its own isolation switch as per the instructions and the diagram. Please contact your installing electrician to rectify if this is not the case.

Loss of function or control between hand piece and receiver

• Try the re-pairing process as outlined above (point 1)
• Try pairing a handpiece from a different fan as outlined above (point 1).
• If the problem persists, call Ventair technical support on 1300 665 926.

Replacing an old or damaged handset

• If you are replacing a handset only (not the receiver), the repairing process (point 1) will need to be performed before the operation of the fan is possible.

IMPORTANT FACTS

Fan Operation:

• Skyfan DC has been designed to optimize airflow with a minimal amount of energy usage. A ceiling fan rotates much more slowly than a traditional style wall, pedestal or desk fan; ceiling fans cool people effectively by introducing slow movement, with high airflow, into the otherwise still, hot air of a room, creating a natural evaporative cooling effect. Fans never actually cool air, like air-conditioning equipment, but use significantly less power.

Normal Wear and Tear

• Over time, moving parts may become slightly loose or worn creating small increases in noise or movement. Fan operation may also be affected by accidental contact by persons or foreign objects. These conditions are not covered under warranty, but a little care and maintenance can reduce or prevent these problems from arising.

Night Noise

• All electric motors, including fan motors, make some noise however, the Skyfan DC fan motor is not susceptible to the noise problems that are commonly experienced with typical Higher wattage, heavier AC type ceiling fan motors. The Skyfan DC Range are one of the quietest fans available and is ideal for all areas of the home especially bedrooms where noise is a crucial consideration.

MAINTENANCE

CARE AND CLEANING:
NOTE: Always turn OFF the power at the mains switch before performing any maintenance or attempting to clean your fan.

• Every 6 months, periodic cleaning of your ceiling fan is the only maintenance required. Use a soft brush or lint free damp cloth to avoid scratching or marking the surface. Please turn off electricity power when you do so.
• Do not soak or immerse your ceiling fan in the water or other liquids. It could damage the motor or the blades and create the possibility of an electrical shock.
• Ensure that the fan does not come in contact with any organic solvents or cleaners.
• To clean the fan blade, wipe with only a damp clean cloth with NO organic solvents or cleaners.
• The motor has a permanently lubricated ball bearing so there is no need to oil.

TECHNICAL INFORMATION

Ceiling Fan Model| Rated Voltage| Rated Power (Motor)| Rated Power (Lamp)| Fan Weight (Kg)
---|---|---|---|---
SKY903WH| 220-240 VAC| 32W| N/A| 3.82
SKY903WH-L| 220-240 VAC| 32W| 20W, LED, 3000K, 4000K, 5000K| 4.16
SKY903BL| 220-240 VAC| 32W| N/A| 3.82
SKY903BL-L| 220-240 VAC| 32W| 20W, LED, 3000K, 4000K, 5000K| 4.16
SKY1203WH| 220-240 VAC| 31W| N/A| 4.00
SKY1203WH-L| 220-240 VAC| 31W| 20W, LED, 3000K, 4000K, 5000K| 4.43
SKY1203BL| 220-240 VAC| 31W| N/A| 4.00
SKY1203BL-L| 220-240 VAC| 31W| 20W, LED, 3000K, 4000K, 5000K| 4.43
SKY1303WH| 220-240 VAC| 31W| N/A| 4.05
SKY1303WH-L| 220-240 VAC| 31W| 20W, LED, 3000K, 4000K, 5000K| 4.39
SKY1303BL| 220-240 VAC| 31W| N/A| 4.05
SKY1303BL-L| 220-240 VAC| 31W| 20W, LED, 3000K, 4000K, 5000K| 4.39
SKY1303TK| 220-240 VAC| 31W| N/A| 4.05
SKY1303TK-L| 220-240 VAC| 31W| 20W, LED, 3000K, 4000K, 5000K| 4.39
SKY1503WH| 220-240 VAC| 43W| N/A| 4.50
SKY1503WH-L| 220-240 VAC| 43W| 20W, LED, 3000K, 4000K, 5000K| 4.70
SKY1503BL| 220-240 VAC| 43W| N/A| 4.50
SKY1503BL-L| 220-240 VAC| 43W| 20W, LED, 3000K, 4000K, 5000K| 4.70
SKY1503TK| 220-240 VAC| 43W| N/A| 4.50
SKY1503TK-L| 220-240 VAC| 43W| 20W, LED, 3000K, 4000K, 5000K| 4.70
Ceiling Fan Model| Rated Voltage| Rated Power (Motor)| Rated Power (Lamp)| Fan Weight (Kg)
---|---|---|---|---
SKY1204WH| 220-240 VAC| 30W| N/A| 4.11
SKY1204WH-L| 220-240 VAC| 30W| 20W, LED, 3000K, 4000K, 5000K| 4.45
SKY1204BL| 220-240 VAC| 30W| N/A| 4.11
SKY1204BL-L| 220-240 VAC| 30W| 20W, LED, 3000K, 4000K, 5000K| 4.45
SKY1404WH| 220-240 VAC| 38W| N/A| 4.31
SKY1404WH-L| 220-240 VAC| 38W| 20W, LED, 3000K, 4000K, 5000K| 4.65
SKY1404BL| 220-240 VAC| 38W| N/A| 4.31
SKY1404BL-L| 220-240 VAC| 38W| 20W, LED, 3000K, 4000K, 5000K| 4.65

WARRANTY INFORMATION

• If you suspect faults relating to installation, contact your installer to rectify them.
• If you suspect there to be a manufacturing defect, lodge a warranty by visiting www.ventair.com.au/warranty or contact Ventair support on 1300 665 926

You will need to provide the following information:

• The name and contact details of the licensed electrician/installer.
• The brand, model number, and serial number (on motor housing).
• The date and place of purchase of the unit.
• The owner’s name, address, and telephone contact numbers.
• The nature of the fault.
• The customer will not gain the benefit of this warranty without claiming with
• Ventair. This warranty is not valid if any repairs or replacement is undertaken without the prior approval of Ventair.
• Please see www.ventair.com.au/warranty for terms and conditions.

References

• Admin - Post Job

Read User Manual Online (PDF format)

Read User Manual Online (PDF format)  >>

Download This Manual (PDF format)

Download this manual  >>