Envision LED RDL-4-5-6-PC Inches Round Retrofit Downlight Instruction Manual

Envision LED RDL-4-5-6-PC Inches Round Retrofit Downlight

Product Specifications

• Brand: Envision LED Lighting
• CCT Selectable: 2700K / 3000K / 3500K / 4000K / 5000K
• Compatible Housing Sizes: 4″, 5″, 6″

Product Usage Instructions

1. With fingertips, pull down firmly on the trim ring until the fixture stops.
2. Squeeze torsion springs together to remove the LED fixture.
3. Disconnect the fixture from the socket adapter.
4. Unscrew the socket adapter from a recessed can.
5. Loosen the wing nut inside the can, slide the socket bracket completely up and tighten the wing nut.
6. Screw socket adapter into existing can socket.
7. Plug the female connector of the fixture into the connector of the socket adapter assembly.
8. Squeeze friction blades to light body. Tuck all wires into the can and carefully push retrofit into the can.
9. To provide enough room in shallow cans, carefully position socket adapter wiring to the side of the LED driver before inserting retrofit trim into the can.
10. Squeeze both torsion spring arms together and insert them into the torsion spring slots (or receiver brackets) of the can.

FAQ

• Q: Can I adjust the colour temperature of the LED luminaire?
• A: Yes, the CCT is selectable between 2700K, 3000K, 3500K, 4000K, and 5000K.
• Q: How do I securely install the LED luminaire into different housing sizes?
• A: Follow the provided instructions to ensure a proper and secure installation based on the housing size (4″, 5″, or 6″).

Introduction

• Please read and understand this entire manual before attempting to assemble, operate or install the product.
• WARNING: Avoid fire or electric shock. Follow installation instructions carefully. Risk of fire or electric shock. LED downlight installation requires knowledge of luminaire electrical systems. If not qualified, do not attempt installation. Suitable for damp locations.
• Install this kit only in luminaires that have the construction features and dimensions shown in the photographs and/or drawings and where the input rating of the retrofit kit does not exceed the input rating of the luminaire. Wear rubber-soled shoes and work on a sturdy ladder. Ground fixture to avoid potential electrical shock. Do not make or alter any open holes in an enclosure of wiring or electrical components during kit installation. To prevent wiring damage or abrasion, do bit expose wiring to edges of sheet metal or other sharp objects.
• CAUTION: Turn off the power at the fuse or circuit breaker box before installation and maintenance to avoid electric shock. This fixture should be used on 120Volt fused circuits only. Fixture must be installed according to the National Electric Code and local building codes. If you are unsure about wiring consult a qualified electrician. THIS FIXTURE BODY IS ONE PIECE, DO NOT DISASSEMBLE OR MAKE ALTERATIONS. Not to be used for emergency lighting.
• Operation is subject to the following two conditions: (1) this device may not cause harmful interference, and (2) this device must accept any interference received, including that may cause undesired operation.
• Retain these instructions for future maintenance reference.

Removing LED Luminaires

1. With fingertips, pull down firmly on trim ring until the fixture stops.
2. Squeeze torsion springs together to remove the LED fixture.
3. Disconnect fixture from socket adapter
4. Unscrew the socket adapter from the recessed can.

5-CCT & Power Adjustment

Switch 1

Selectable Power

• 4″ Selectable: 8W / 10W / 12W
• 6″ Selectable: 12W / 15W / 18W

Switch 2

• 5-CCT Selectable
• 2700K / 3000K / 3500K / 4000K / 5000K

Install Into Housings

1. Loosen the wing nut inside the can, slide the socket bracket completely up and tighten wing nut. (Fig. 1)
2. Screw socket adapter into existing can socket. (Fig. 2)
3. Plug the female connector of the fixture into the connector of the socket adapter assembly. (Fig. 3 & Fig. 7)

For 4″ Retrofit

• Squeeze friction blades to the light body (Fig. 4)
• Tuck all wires into a can and carefully push retrofit into a can. To provide enough room in shallow cans, carefully position socket adapter wiring to the side of LED driver before inserting retrofit trim into the can.

For 5/6″ Retrofit

• Squeeze both torsion spring arms together and insert into the torsion spring slots (or receiver brackets) of the can (Fig. 6)

WWW.ENVISIONLEDLIGHTING.COM.

References

• Envision Led - Envision LED Lighting

Read User Manual Online (PDF format)

Read User Manual Online (PDF format)  >>

Download This Manual (PDF format)

Download this manual  >>