STERLING 77301100 Air Massage Bath Owner’s Manual
- July 4, 2024
- STERLING
Table of Contents
STERLING 77301100 Air Massage Bath
Specifications
- Product Name: 72 x 36 air massage bath
- Model Number: 77301100
- Dimensions:
- Length: 72″ (1829 mm)
- Width: 36″ (914 mm)
- Height: 20-5/16″ (516 mm)
- Weight: 83 lbs (37.6 kg)
- Water Depth: 15-1/4″ (387 mm)
- Water Capacity: 68 gal (257.4 L)
- Electrical Requirements:
- Blower: 120 V, 9.2 A, 60 Hz
- Heater: 300 W
- Drain Location: Reversible
Product Usage Instructions
Installation
- Install this product according to the provided installation instructions.
- Ensure one grounded electrical outlet is available within 24″ (610 mm) of each component.
- Size the drain cutout to fit the drain assembly that will be used.
- Blower service access is required for maintenance.
Electrical Service Requirements
- One dedicated circuit is required, protected with a Class A Ground-Fault circuit interrupter (GFCI).
- Outside North America, this device may be known as a Residual Current Device (RCD).
- Blower and Heater require : 120 V, 15 A, 60 Hz
Notes on Installation
- End stud positioning is critical if nailing-in flanges are to be used.
- Studs should be positioned as shown for support clip or roofing nail installation.
FAQ
Q: What is the water capacity of the air massage bath?
A: The water capacity is 68 gallons (257.4 liters).
Q: What are the electrical requirements for the blower and heater?
A: The blower and heater require 120 V, 9.2 A, 60 Hz, and 300 W respectively.
Features
- 15-1/4″ soaking depth
- A reversible drain can be installed as a left- or right-hand drain
- Suitable for tile-down applications
- Air Massage, three-speed blower, integrated heater, arched armrests, contoured backrest, and lumbar support
Material
Made from solid Vikrell® material for strength, durability, and lasting beauty
Installation
Drop-in
Recommended Products/Accessories
71317100 Tile-in flange kit for 72″ soaking baths
Codes/Standards
- ASME A112.19.7/CSA B45.10
- CSA B45.5/IAPMO Z124
- ASTM E162
- ASTM E662
- UL 1795
- CSA C22.2 No. 218.2
STERLING® Vikrell® or Acrylic Baths and Shower Bases Ten-Year Limited Warranty
- See the website for detailed warranty information.
Dimension
Required Electrical Service
- One dedicated circuit is required, protected with Class A Ground-Fault Circuit-Interrupter (GFCI). Outside North America, this device may be known as a Residual Current Device (RCD).
- Blower, Heater: 120 V, 15 A, 60 Hz
Technical Information
- All product dimensions are nominal.
- Drain location: Reversible
- Basin area, bottom: 50-3/8″ x 21-3/4″ (1280 mm x 552 mm)
- Basin area, top: 58-1/4″ x 27″ (1480 mm x 686 mm)
- Weight: 83 lbs (37.6 kg)
- Minimum floor load: 41 lbs/ft² (200.2 kg/m²)
- Water depth: 15-1/4″ (387 mm)
- Water capacity: 68 gal (257.4 L)
- Electrical component rating: Blower: 120 V, 9.2 A, 60 Hz
- Heater: 300 W
- Minimum flat for door: 3″ (76 mm)
Notes
- Install this product according to the installation instructions.
- Provide one grounded electrical outlet within 24″ (610 mm) of each component.
- Size the drain cutout to fit the drain assembly that will be used.
- Blower service access is required.
- End stud positioning is critical if nailing-in flanges are to be used.
- Studs should be positioned roughly as shown for support clip or roofing nail installation.
- 1-800-STERLING (1-800-783-7546)
- Kohler Co. reserves the right to make revisions without notice to product specifications.
- For the most current Specification Sheet, go towww.sterlingplumbing.com. 3-24-2024 21:23 – US
References
Read User Manual Online (PDF format)
Read User Manual Online (PDF format) >>