THUNDEROBOT ML602 Gaming Mouse Instruction Manual
- July 2, 2024
- THUNDEROBOT
Table of Contents
ML602 Gaming Mouse
Instruction Manual
Please read the instructions carefully before using this product and keep it well for referent.
LAYOUT
Size: 126 63.8 39.8 mm
| A. Left button | G. TypeC port |
|---|---|
| B. Right button | H. Mode switch |
| C. Scroll wheel | I. BT pairing button |
| D. DPI button | J. Optical sensor |
| E. Forward button | K. 2.4G wireless dongle compartment |
| F. Backward button | L. 2.4G wireless dongle |
OS SUPPORT
Windows 11/Windows 10/Windows 8/Windows 7/ Windowse Vista/WindowseXP
Mac OS X 10.8 – 10.11, iOS 13.1, Android 4.3 and newer
WARNING
- Do not disassemble, crush, heat, or incinerate the battery.
- Do not allow sharp objects, screwdrivers, or similar items to touch or pry the battery.
*The above operations may cause the battery to ignite or burn.
SPECIFICATION
DPIINDICATORS
| DPI| INDICATOR COLOR
---|---|---
1| 800| RED
2| 1600| GREEN
3| 2400| BLUE
4| 3200| YELLOW
5| 6400| PINKY
PACKING LIST
Mouse 1
USB cable 1
User manual / Certificate 1
2.4G wireless dongle 1
INSTRUCTIONS FOR USE
Mouse Control Mode
Bottom three-stage switch:
- Power off mode (OFF): Turn off directly in wireless mode.
- Power on, 2.4G mode (2.4G): Scroll wheel green light flashes, insert the 2.4G receiver into the computer’s USB port, and the mouse will work.
- Power on, Bluetooth mode (BT): Scroll wheel blue light flashes, approach the device to be connected, press and hold the bottom Bluetooth pairing button for 3 seconds to enter pairing mode (scroll wheel blue light flashes rapidly), and then it can be paired with the device.
“Wired mode: Plug and play, not affected by the switch, default wired mode connection in simultaneous connection with wired and other modes. Default charging in wired mode.
Polling Rate Adjustment
Default polling rate is 1000Hz; adjust to four gears by right click + forward
side button: 125Hz (red light flashes on scroll wheel) – 250Hz (blue light
flashes on scroll wheel) – $00Hz (green light flashes on scroll wheel) –
1000Hz (purple light flashes on scroll wheel).
Other Functions
Auto Sleep Mode
In 125Hz/250Hz/500Hz, the mouse enters sleep mode after one minute of
inactivity and wakes up by moving.
In 1000H7z, the mouse enters sleep mode after 8 minutes of inactivity and
wakes up by moving.
Low Voltage Warning
When the mouse is low on battery, the indicator light near the scroll wheel
will flash red to remind you to charge in time.
Charging Display
During charging, the LED indicator light near the scroll wheel will be red.
After the battery
is fully charged, this LED indicator light will switch back to default Dp
indication.
Safety reminder:
Charging voltage supports up to 5V, and charging current should not exceed
1A.
FCC Warning
This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation. This equipment generates, uses and can radiate radio frequency energy and, if not installed and used in accordance with the instructions, may cause harmful interference to radio communications. However, there is no guarantee that interference will not occur ina particular installation. If this equipment does cause harmful interference to radio or television reception, which can be determined by turning the equipment off and on, the user is encouraged to try to correct the interference by one or more of the following measures:
- Reorient or relocate the receiving antenna.
- Increase the separation between the equipment and receiver.
- Connect the equipment into an outlet on a circuit different from that to which the receiver is connected.
- Consult the dealer or an experienced radio/TV technician for help.
Caution : Any changes or modifications to this device not explicitly
approved by manufacturer could void your authority to operate this equipment.
This device complies with part 15 of the FCC Rules. Operation is subject to
the following two conditions:
- This device may not cause harmful interference, and
- this device must accept any interference received, including interference that may cause undesired operation.
The device has been evaluated to meet general RF exposure requirement. The device can be used in portable exposure condition without restriction.