Halsey Taylor SCWT14WQ1K Barrier Free Water Cooler Owner’s Manual
- July 1, 2024
- Halsey Taylor
Table of Contents
Halsey Taylor SCWT14WQ1K Barrier Free Water Cooler
Specifications
- Model: SCWT14WQ*1K
- Product Name: SCWTTM Series Barrier-Free Water Cooler
- Refrigerant: HFC-134A
- Recommended Circuit: Dedicated circuit with load protection sized for 20 amps and hospital-grade GFCI
Product Usage Instructions
Push Button Valve Adjustment
To adjust the stream height and eliminate valve lever free play or continuous flow from the bubbler, follow these steps:
- Locate the stream height adjustment screw (See Fig. 3).
- Adjust the screw as needed to achieve the correct stream height.
Condenser Water Valve Adjustment
To adjust the condenser water valve, follow these steps:
- Start up the compressor by depressing the cooler push button(See Fig. 1 – Item 4).
- Keep water running during the entire readjustment procedure.
FAQ
-
How do I adjust the stream height of the water cooler?
To adjust the stream height, locate the stream height adjustment screw and turn it to achieve the desired height as per the user manual. -
What refrigerant does the water cooler use?
The water cooler uses HFC-134A refrigerant as specified in the user manual.
Note : Danger! Electric shock hazard. Disconnect power before servicing unit.
**USES HFC-134A REFRIGERANT
**
-
A = RECOMMENDED WATER SUPPLY LOCATION 3/8 O.D. UNPLATED COPPER TUBE CONNECT STUB OUT 1-1/2 IN. (38mm)
FROM WALL SHUT OFF BY OTHERS -
B = RECOMMENDED LOCATION FOR WASTE OUTLET 1-1/4” O.D. DRAIN
-
C = 1-1/4 TRAP NOT FURNISHED
-
D = ELECTRICAL OUTLET LOCATION
-
E = INSURE PROPER VENTILATION BY MAINTAINING 4″ (102mm) (MIN.) CLEARANCE FROM CABINET LOUVERS
TO WALL. -
F = POWER CORD 4′ (1219mm) LONG
-
G = WALL SCREW HOLES
-
H = 2 X 4 BLOCKING
PUSH BUTTON VALVE ADJUSTMENT
WIRING DIAGRAM
This drawing is merely for illustrating the components of the electrical system
CONDENSER WATER VALVE ADJUSTMENT
| ITEM NO. | PART NO. | DESCRIPTION |
|---|---|---|
| 1 | 15005C | Nut-Regulator Retaining |
| 2 | 51544C | Bubbler |
| 3 | 101507531550 | Push Button Stem |
| 4 | 101453431640 | Cap Push Button |
| 5 | 102639931640 | Drain Plug |
| 6 | 160270508640 | Strainer Plate |
| 7 | 28346C | Basin |
| 8 | 26860C | Regulator Lever |
| 9 | 26861C | Pivot Bracket |
| 10 | 26862C | Regulator Retaining Bracket |
| 11 | 98773C | Cold Control |
| *12 | 36312C | Compressor Service Pak |
| 13 | 35840C | Overload |
| 14 | 35768C | Relay Cover |
| 15 | 75589C | Gasket |
| 16 | 192668451550 | Power Cord |
| **17 | 45696C | Tailpipe Assy |
| 18 | 66581C | Heat Exchanger |
| 19 | 75561C | Elbow – 3/8″ |
| 20 | 50986C | Regulator Holder |
| 21 | 66798C | Condenser Assy |
| 22 | 66811C | Evaporator |
| 23 | 55880C | Regulator Mounting Bracket |
| 24 | 61314C | Regulator |
| 25 | 66203C | Drier |
| 26 | 75494C | Check Valve |
| 27 | 55996C | Strainer |
| 28 | 55913C | Adaptor-Drain W/O Holes |
| 29 | 75588C | Nut – Slip Joint 1-1/4 |
| 30 | 56159C | Nipple – Bubbler |
| 31 | 70682C | Tee – 1/4 |
| 32 | See Color Table | Side Panel – Right |
| 33 | See Color Table | Side Panel – Left |
| 34 | 35843C | Relay |
| 35 | 35844C | Capacitor |
| 36 | 56092C | Poly Tubing (Cut To Length) |
| 37 | 70683C | Union – 1/4 |
| NS | 75583C | Elbow – 5/16″ x 1/4″ |
| NS | See Color Table | Front Panel |
The condenser water valve is factory preset for a condenser water outlet temperature of 95° to 105° F. If actual temperature varies greatly from this, readjust water flow rate at the valve using the following procedures.
-
START UP COMPRESSOR
This can be accomplished by depressing the cooler push button (See Fig. 1 – Item 4). Keep water running during the entire readjustment procedure. -
ADJUSTMENT CONDENSER WATER VALVE
Adjust valve by rotating adjustment stem. Rotating stem clockwise will increase water flow. Counterclockwise rotation will decrease water flow. Increasing water flow will result in a lower condenser outlet temperature, while decreasing water flow will result in a higher outlet temperature. Proper adjustment is attained when condenser outlet temperature is 95° to 105° F .
Includes Items 15, 28 & 29
INCLUDES RELAY & OVERLOAD. IF UNDER WARRANTY, REPLACE WITH SAME COMPRESSOR
USED IN ORIGINAL ASSEMBLY.
NOTE : All correspondence pertaining to any of the above water coolers or
orders for repair parts MUST include Model No. and Serial No. of cooler, name
and part number of replacement part.
COLOR
| ****
RIGHT PANEL
| ****
LEFT PANEL
| ****
FRONT PANEL
---|---|---|---
Platinum (PV)| 401536248410| 401536348410| 401507448410
Stnlss Stl (SS)| 401536242830| 401536342830| 401507442830
OAK BROOK, IL 60523
630.574.3500
FOR PARTS CONTACT YOUR LOCAL DISTRIBUTOR OR VISIT OUR WEBSITE
WWW.HALSEYTAYLOR.COM
Read User Manual Online (PDF format)
Read User Manual Online (PDF format) >>