Halsey Taylor HVR8HD Series Barrier Free Water Coolers Owner’s Manual

June 12, 2024
Halsey Taylor

*HVR8HD1C,2B,3B, HVRDHDB, HVR8HDWF1C, 2B.3B
Owners Manual
MANUAL DEL PROPIETARIO HALSEY TAYLOR
HVR8HD™
Series Barrier-Free Water Coolers
Halsey Taylor HVR8HD Series Barrier Free Water Coolers
Patent zurn-elkay.com/patents
**

HVR8HD Series Barrier Free Water Coolers

WARNING: Cancer and Reproductive Harm – www.P65Warnings.ca.gov

Note: Danger! Electrical shock hazard. Disconnect power before servicing unit.
Uses HFC-134A refrigerant
Usa refrigerante HFC-134AHalsey Taylor HVR8HD Series Barrier Free Water
Coolers - power
Halsey Taylor HVR8HD Series Barrier Free Water Coolers -
INSTALLATION

  • ADA REQUIREMENT

  • REQUISITO DE A.D.A.

  • EXIGENCE ADA

  • REDUCE HEIGHT BY 3” FOR INSTALLATION OF CHILDREN’S ADA COOLER LEGEND
    A = RECOMMENDED WATER SUPPLY LOCATION. SHUT OFF VALVE (NOT FURNISHED) TO ACCEPT 3/8” O.D. UNPLATED COPPER TUBE.
    COPPER TUBE.
    B = RECOMMENDED LOCATION FOR WASTE OUTLET 1-1/4” O.D. DRAIN
    C = 1-1/4 TRAP NOT FURNISHED
    PURGADOR DE 1¼ NO PROPORCIONADO

    SIPHON 1-1/4 NON FOURNI
    D = ELECTRICAL SUPPLY (3) WIRE RECESSED BOX
    E = INSURE PROPER VENTILATION BY MAINTAINING 6” (152 mm) (MIN.) CLEARANCE FROM CABINET LOUVERS TO WALL.
    F = 7/16 BOLT HOLES FOR FASTENING UNIT TO WALL
    IMPORTANT
    ALL SERVICE TO BE PERFORMED BY AN
    AUTHORIZED SERVICE PERSON
    HANGER BRACKETS & TRAP
    INSTALLATION**

    1. Remove hanger bracket fastened to back ofcooler by removing one (1) screw.

    2. Mount the hanger bracket and trap as shown in Figure 2.
      NOTE: Hanger Bracket MUST be supportedsecurely. Add fixture support carrier if wall will not provide adequate support.
      IMPORTANT:
       6-13/16 in. (173mm) dimension from wall tocenterline of trap must be maintained for properfit.
       Anchor hanger securely to wall using all five
      (5) 5/16 in. dia. mounting holes.

    3.  Install straight valve for 3/8” O.D. tube.
      INSTALLATION OF COOLER

    4.  Hang the cooler on the hanger bracket. Becertain the hanger bracket is engaged properly in the slots on the cooler back as shown in Figure2.

    5. Loosen the two (2) screws holding the lower front panel at the bottom of cooler base (Use torx bit sold separately). Remove the front panel and set aside.

    6. Connect water inlet line–See Note 4 of General Instructions.

    7. Remove the slip nut and gasket from the trap and install them on the cooler waste line making  surethat the  end of the waste line fits into the trap.  Assemble the slip nut  and gasket to the trap and tighten securely. Recommend fastening cooler to wall  using 5/16” bolt holes. (see fig.2, “F”)
      START UP
      Also See General Instructions

    8.  Stream height is factory set at 45-50 PSI. Ifsupply pressure varies greatly from this, adjust screw using the access hole in the pushbutton
      (insert screwdriver). CW adjustment will raisestream and CCW adjustment will lower stream. For best adjustment, stream should hit basinapproximately 6-1/2” (165mm) from bubbler.
      CLEANING

    9. Recommended: Elkay’s Stainless Butler Cleaner (Item LKSB16EA).
      Warm, soapy water or mild household cleaning products can be used to clean the exterior with a clean, soft cloth. Use of harsh chemicals, petroleum based or abrasive cleaners will void the warranty.

Halsey Taylor HVR8HD Series Barrier Free Water Coolers -
BasinHalsey Taylor HVR8HD Series
Barrier Free Water Coolers - Basixn

ITEM NO. PART NO. DESCRIPTION
1 98481C Kit – VR Bubbler/Nipple/ Gaskets/Screen
2 98777C Kit- Compr Mtg Hdwe/Grommets/ Clips/Studs
3 27124C Cover – Cold Control
4 45888C Assy. Drain/Tailpipe
5 98851C KIt – Heat Exchanger/Drier
6 98788C Kit – Fan Motor/Blade/Nut
7 56033C Washer
8 98773C Kit – Cold Control/Screws
9 28898C Panel – Access
10 35870C Power Cord
*11 36322C Compressor Serv. Pak EMI 70
12 238 Kit – Relay/OverLoad/Cover
13 56087C Extension – Push Button
14 50986C Holder – Regulator
15 75739C Screw – #10-24 x .50 Pinned Torx
16 56092C Tubing – Poly (Cut To length)
17 98530C Kit – Regulator with Spring
18 45736C Half Nut – Regulator
19 66703C Drier
20 98724C Kit – Evaporator Assembly
21 70002C Screw – #10 x 1/2” Lg. HHSM
22 1.11543E+11 Nut – #6-32 Hex.
23 45768C Drain Plug 1-1/2
24 1000001602 Kit – 75583C Elbow 5/16” x 1/4” (3 Pack)
25 28870C Cabinet – Stainless Steel
26 28876C Bracket – Fan Mounting
27 45662C Button – Push
28 45738C Sleeve – Push Button
29 75672C Cap Screw
30 56163C Gasket – Drain
31 36282C Wire – Fan Motor
32 28894C Panel – Front Lower (NS)
33 98418C Kit – Condenser Replacement
34 28875C Shroud Fan
35 40045C Hex Nut
36 28878C Bracket – Support
37 28877C Shelf – Evaporator Mounting
38 55996C Strainer (See “General Instructions”)
NS 75520C Torx Tool – T25
NS 28874C Hanger Bracket

PARTS LIST 220/240V – LISTA DE PIEZAS 220/240V – LISTE DES PIÈCES 220/240V

NO PART NO DESCRIPTION
6 243 Kit – Fan Motor/Blade/Nut 220/240V
*11 1000002147 Compressor Serv. Pak (220V/50Hz)
12 1000002146 Compressor Serv. Pak (220V/60Hz)
98751C Kit – Relay/OverLoad/Cover (50 Hz)
98752C Kit – Relay/OverLoad/Cover (60Hz)
39 35827C Power Cord
40 35826C Power Inlet

*REPLACE WITH SAME COMPRESSOR USED
IN ORIGINAL ASSEMBLY.
NOTE: All correspondence pertaining to any of the above water coolers or orders for repair parts MUST include Model No. and Serial No. of cooler, name and part number of replacement part.

1333 BUTTERFIELD ROAD,
DOWNERS GROVE, IL 60515
630.574.3500
www.halseytaylor.com
FOR PARTS CONTACT YOUR LOCAL DISTRIBUTOR OR VISIT OUR WEBSITE WWW.HALSEYTAYLOR.COM
PARA PIEZAS DE REEMPLAZO PÓNGASE EN CONTACTO CON SU DISTRIBUIDOR LOCAL O VISITE NUESTRO SITIO DE WEB WWW.HALSEYTAYLOR.COM
POUR VOUS PROCURER DES PIOCES, CONTACTEZ VOTRE DISTRIBUTEUR LOCAL OU VISITEZ NOTRE SITE WEB A L’ADRESSE WWW.HALSEYTAYLOR.COM
PRINTED IN U.S.A.
IMPRESO EN LOS E.E.U.U.
IMPRIMÉ AUX É.-U.

References

Read User Manual Online (PDF format)

Read User Manual Online (PDF format)  >>

Download This Manual (PDF format)

Download this manual  >>

Related Manuals