behringer 1630 Frequency Shifter User Guide

: August 28, 2024
: Behringer

Table of Contents

behringer 1630 Frequency Shifter
Product Usage Instructions
FAQ
Safety Instruction
LIMITED WARRANTY
BODE FREQUENCY SHIFTER 1630 Controls
Power Connection
Installation
Specifications
FCC STATEMENT
References
Read User Manual Online (PDF format)
Download This Manual (PDF format)

behringer 1630 Frequency Shifter

Specifications

Product Name: BODE FREQUENCY SHIFTER 1630
Type: Analog Frequency Shifter
Compatibility: Eurorack V 1.0

Product Usage Instructions

Read and follow all provided instructions.
Avoid water contact, except for outdoor use.
Clean the product only with a dry cloth.
Ensure ventilation openings are not blocked and install as per manufacturer’s guidelines.
Avoid placing near heat sources like radiators or stoves.
Use only manufacturer-specified attachments and accessories.
Use recommended carts, stands, or tables to prevent tip-overs.
Avoid installation in confined spaces like bookcases.
Keep away from naked flame sources such as lit candles.

For detailed warranty terms and conditions as well as additional information about Music Tribe’s Limited Warranty, please visit the official website at community.musictribe.com/support.

FAQ

Q: Can I clean the BODE FREQUENCY SHIFTER 1630 with water?
A: No, clean the product only with a dry cloth to prevent damage.
Q: What should I do if the ventilation openings are blocked?
A: Ensure the ventilation openings are clear to prevent overheating of the device.
Q: Can I use any accessories with the BODE FREQUENCY SHIFTER 1630?
A: It is recommended to use only accessories specified by the manufacturer to ensure proper functionality and safety.

Safety Instruction

Please read and follow all instructions.
Keep the apparatus away from water, except for outdoor products.
Clean only with a dry cloth.
Do not block any ventilation openings. Install per the manufacturer’s instructions.
Do not install near any heat sources such as radiators, heat registers, stoves, or other apparatus (including amplifiers) that produce heat.
Use only attachments/ accessories specified by the manufacturer.
Use only specified carts, stands, tripods, brackets, or tables. Use caution to prevent tip-overs when moving the cart/apparatus combination.
Avoid installing in confined spaces like bookcases.
Do not place near naked flame sources, such as lighted candles.
Operating temperature range 5° to 45°C (41° to 113°F).

LEGAL DISCLAIMER
Music Tribe accepts no liability for any loss that may be suffered by any person who relies either wholly or in part upon any description, photograph, or statement contained herein. Technical specifications, appearances, and other information are subject to change without notice. All trademarks are the property of their respective owners. Midas, Klark Teknik, Lab Gruppen, Lake, Tannoy, Turbosound, TC Electronic, TC Helicon, Behringer, Bugera, Aston Microphones, and Coolaudio are trademarks or registered trademarks of Music Tribe Global Brands Ltd. © Music Tribe Global Brands Ltd. 2024 All rights reserved.

LIMITED WARRANTY

For the applicable warranty terms and conditions and additional information regarding Music Tribe’s Limited Warranty, please see complete details online at community.musictribe.com/support.

BODE FREQUENCY SHIFTER 1630 Controls

Controls
The BODE FREQUENCY SHIFTER 1630 shifts the frequency spectrum of a given signal by either a fixed amount or one that varies using control voltages. Its uses include tonal modification, feedback suppression, and frequency modulation.

SHIFT CONTROL – use this control to set the amount of fixed frequency shift, according to the setting of the Scale control (2). Turning the control CW shifts the frequency upwards; CCW shifts down. Note that frequencies cannot be shifted below 0 Hz, so when using a low-frequency input once a 0 Hz downshift is reached the downshift will wrap around to become an upshift.
SCALE – use this switch to set the scale for the frequency shift. The available options are:
- 0 – no shifting takes place, Shift control (1) and CTRL inputs are inactive.
- This mode should be used to disable frequency shifting, or for calibration.
- EXP – shifting takes place on an exponential scale, from +2 Hz to +2 kHz, as marked on the Exponential scale, providing a 1 V/Octave shift which can be controlled using the CTRL inputs (7).
- 5 – Gives a linear shift of +5 Hz CW or -5 Hz CCW.
- 50 – Gives a linear shift of +50 Hz CW or -50 Hz CCW.
- 500 – Gives a linear shift of +500 Hz CW or -500 Hz CCW.
- 5k – Gives a linear shift of +5 kHz CW or -5 kHz CCW.
SQUELCH THRESHOLD – use this control to suppress the output of the frequency shifter when the input level falls below the desired threshold, from 0 dBu to -60 dBu. When the squelch circuit is passing a signal then the LED above the control will be lit. The squelch control can be disabled by removing the jumper between pins 1 and 2 of the 12-pin test header on the underside of the circuit board (see below).
ZERO ADJUST – use this control to calibrate the amount of shift control zero position when an input signal is present. The speed of the flashing LED above the control will reduce until it is close to zero (no shift). This control can also be used as a fine adjustment of the amount of shifts.
MIXTURE – use this control to balance the amount of A and B signals present on the Mix Outputs (10). CCW biases towards A, CW towards B.
SIG IN – use this 3.5 mm TS jack to input a signal to be frequency-shifted. Maximum input level is +12 dBu.
CTRL INPUTS 1-3 – use these 3.5 mm TS jacks to control the shift amount using external CV sources. The three inputs are summed together with the Shift control (1). Maximum voltage between the three inputs and the Shift control is 10 V. If the amount of shift control is fully CCW the control input range is 0 V to +10 V, If the amount of shift control is fully CW the control input range is -10 V to 0 V.
OUT A – use these parallel 3.5 mm TS jacks to get the frequency shifted output.
OUT B – use these parallel 3.5 mm TS jacks to get an inverted frequency shifted output, where the frequency shifts down if A shifts up, and vice versa.
MIX OUT – use these 3.5 mm TS jacks to get a mixed output of A and B according to the setting of control 5.

12-PIN TEST HEADER
The Bode 1630 has a twelve-pin test header on the underside of the main PCB, at the right-hand side. The pin layout is as follows:

Pin| | Pin|
---|---|---|---
1| Ground| 2| Squelch Enable
3| Variable Osc Out| 4| Fixed Osc 1 Out
5| Fixed Osc 2 Out| 6| BFO Filter 1 Out
7| BFO Filter 2 Out| 8| Ground
9| Bode Filter 1 Out| 10| Bode Filter 2 Out
11| Multiplier 1 Out| 12| Multiplier 2 Out

It is recommended that the squelch enable jumper is left in place unless its removal is strictly necessary.

Power Connection

Connect end P1 to the module socket
Connect end P2 to the power supply

The module comes with the required power cable for connecting to a standard Eurorack power supply system. Follow these steps to connect power to the module. It is easier to make these connections before the module has been mounted into a rack case.

Turn the power supply or rack case power off and disconnect the power cable.
Insert the 16-pin connector on the power cable into the socket on the power supply or rack case. The connector has a tab that will align with the gap in the socket, so it cannot be inserted incorrectly. If the power supply does not have a keyed socket, be sure to orient pin 1 (-12 V) with the red stripe on the cable.
Insert the 10-pin connector into the socket on the back of the module. The connector has a tab that will align with the socket for correct orientation.
After both ends of the power cable have been securely attached, you may mount the module in a case and turn on the power supply.

Installation

The necessary screws are included with the module for mounting in a Eurorack case. Connect the power cable before mounting.
Depending on the rack case, there may be a series of fixed holes spaced 2 HP apart along the length of the case, or a track that allows individual threaded plates to slide along the length of the case. The free-moving threaded plates allow precise positioning of the module, but each plate should be positioned in approximate relation to the mounting holes in your module before attaching the screws.
Hold the module against the Eurorack rails so that each of the mounting holes is aligned with a threaded rail or threaded plate. Attach the screws part way to start, which will allow small adjustments to the positioning while you get them all aligned. After the final position has been established, tighten the screws down.

Specifications

Inputs
Signal Input

Type: 1 x 3.5 mm TS jack, AC coupled
Impedance: 50 kΩ, unbalanced
Maximum input level: +12 dBu

Control Inputs

Type: 3 x 3.5 mm TS jack, DC coupled
Impedance: 100 kΩ, unbalanced
CV range: 10 V

Outputs
Outputs A

Type: 2 x 3.5 mm TS jack, DC coupled
Impedance: 1 kΩ, unbalanced
Maximum output level: +12 dBu
Output signal: None inverted frequency shift

Outputs B

Type: 2 x 3.5 mm TS jack, DC coupled
Impedance: 1 kΩ, unbalanced
Maximum output level: +12 dBu
Output signal: Inverted frequency shift

Mix outputs

Type: 2 x 3.5 mm TS jack, DC coupled
Impedance: 1 kΩ, unbalanced
Maximum output level: +12 dBu
Output signal: Output A or B or a mixture of both

Test connector

Type: 1 x 12 pin 0.1” male header
Impedance: 1 kΩ, unbalanced
Available signals: Var Osc, Fixed Osc 1&2, BFO filters 1&2, Dome filters 1&2, Out 1&2, Squelch enable link, GND

Controls & Indicators

Amount of shift: Frequency shift to a maximum of ±5 kHz
Zero adjust: Fine frequency shift ±220 Hz
Zero adjust: LED Flashes once per carrier cycle
Scale rotary switch: 0 (off), Exponential +2 Hz to +2 kHz, 1 V/Octave Linear ±5 Hz, ±50 Hz, ±500 Hz, ±5 kHz
Squelch threshold: -60 dBu to 0 dBu
Squelch threshold LED: Lights for input signals above the threshold level
Mixture: Pans between the A and B outputs

System

Frequency range: <30 Hz to >16 kHz
Input to output gain: Unity gain
Control input matching: Better than 0.1%

Power Requirements

Power supply: Eurorack
Current draw: 110 mA (+12 V), 110 mA (-12 V)

Physical

Operating Temperature: 5° C – 45° C (41° F – 113°F)
Dimensions (H x W x D): 128.5 x 70.8 x 53.3 mm (5.1 x 2.8 x 2.10″)
Rack units: 14 HP
Weight: 172 g (6.1 oz)

FEDERAL COMMUNICATIONS

COMMISSION COMPLIANCE INFORMATION

Behringer

BODE FREQUENCY SHIFTER 1630

Responsible Party Name:
Music Tribe Commercial NV Inc.
Address:
122 E. 42nd St.1, 8th Floor NY,
NY 10168, United States
Email Address:
legal@musictribe.com

FCC STATEMENT

BODE FREQUENCY SHIFTER 1630
This equipment has been tested and found to comply with the limits for a Class B digital device, according to part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation. This equipment generates, uses, and can radiate radio frequency energy and, if not installed and used under the instructions, may cause harmful interference to radio communications. However, there is no guarantee that interference will not occur in a particular installation. If this equipment does cause harmful interference to radio or television reception, which can be determined by turning the equipment off and on, the user is encouraged to try to correct the interference by one or more of the following measures:

Reorient or relocate the receiving antenna.
Increase the separation between the equipment and the receiver.
Connect the equipment to an outlet on a circuit different from that to which the receiver is connected.
Consult the dealer or an experienced radio/TV technician for help.

This equipment complies with Part 15 of the FCC rules. Operation is subject to the following two conditions:

this device may not cause harmful interference, and
this device must accept any interference received, including interference that may cause undesired operation.

Important information
Changes or modifications to the equipment not expressly approved by Music Tribe can void the user’s authority to use the equipment.

Hereby, Music Tribe declares that this product complies with Directive 2014/30/EU, Directive 2011/65/EU and Amendment 2015/863/EU, Directive 2012/19/EU, Regulation 519/2012 REACH SVHC and Directive 1907/2006/EC.

Full text of EU DoC is available at https://community.musictribe.com/
EU Representative: Music Tribe Brands DK A/S
Address: Gammel Strand 44, DK-1202
København K, Denmark
UK Representative: Music Tribe Brands UK Ltd.
Address: 8th Floor, 20 Farringdon Street
London EC4A 4AB, United Kingdom

Correct disposal of this product: This symbol indicates that this product must not be disposed of with household waste, according to the WEEE Directive (2012/19/EU) and your national law.

This product should be taken to a collection center licensed for the recycling of waste electrical and electronic equipment (EEE).
The mishandling of this type of waste could have a possible negative impact on the environment and human health due to potentially hazardous substances that are generally associated with EEE. At the same time, your cooperation in the correct disposal of this product will contribute to the efficient use of natural resources. For more information about where you can take your waste equipment for recycling, please contact your local city office or your household waste collection service.