VISTA Pro 1092 Flood Light Installation Guide
- July 1, 2024
- Vista Pro
Table of Contents
VISTA Pro 1092 Flood Light
Specifications
- Model: 1092
- Lamp Type: PAR30
LED Lamp Installation/Replacement
Caution
- Do not exceed the maximum wattage marked on the luminaire label.
- Disconnect from the electrical supply before servicing to prevent electrical shock.
- When replacing the lamp, use a soft cloth or plastic wrapping to handle it and avoid touching it with bare hands.
INSTALLATION INSTRUCTIONS
WARNING
Luminaire must be installed and grounded in accordance with the National
Electrical Code (NEC) and local codes. For portable stake or surface mount
using a cord and plug, the luminaire must be plugged into a receptacle
protected by a ground fault circuit interrupter (GFI). Failure to do so may
result in serious injury and/or damage to the luminaire.
MAINTENANCE
To assure proper operation and efficiency and to prevent luminaire
overheating, lens must be kept clean and free of dirt, dust, leaves, trash and
mineral deposits from water. A regular schedule maintenance program is
recommended.
SAFETY WARNING
Luminaire can become hot depending on lamp wattage. Lens and housing around
lamp can become hot enough to blister hands. Particular care should be taken
not to locate luminaires where small children can reach them if high wattage
lamps are used.
NOTE : Always use UL recognized wire connectors for connections.
LUMINAIRE IS UL LISTED FOR ABOVE GRADE INSTALLATION ONLY.
Luminaire Mounting
- Make sure electrical supply is off at circuit breaker before starting luminaire installation or servicing luminaire.
- Thread luminaire onto junction box or other mounting device until it is at desired direction using thread sealant. Tighten jam nut (provided) to ensure the luminaire is locked to adjusted position.
- Attach luminaire leads to line in leads observing polarity, black to black, white to white and green to ground using silicone filled safety connectors (provided).
- Attach junction box cover with luminaire to junction box (by others). Make sure not to pinch wires that may be sandwiched between cover and box.
- Coat exposed luminaire threads with thread sealant to keep moisture from entering junction box or other mounting device.
- To adjust luminaire aiming angle, loosen adjustable knuckle screw. Do not disengage totally. Hold luminaire at selected angle and tighten knuckle screw firmly.
- Install lamp.
- Coat all exposed screws with silicone grease.
- Supply power to the luminaire and check for proper operation.
WARNING : TO REDUCE THE RISK OF FIRE, OR INJURY TO PERSONS:
- Turn off/unplug and allow to cool before replacing lamp.
- Lamps get hot quickly! Contact only switch/plug when turning on.
- Do not touch hot lens, guard or enclosure.
- Keep lamp away from material that may burn.
- Do not touch the lamp at any time. Use a soft cloth. Oil from the skin may damage lamp.
- Do not operate luminaire fitting with a missing or damaged cover.
LED LAMP INSTALLATION/REPLACEMENT
CAUTION : Do not exceed maximum wattage marked on luminaire label.
-
To prevent electrical shock, disconnect from electrical supply before service.
-
Loosen screw from shroud.
-
Remove shroud and gasket to expose lamp.
-
Replace lamp with correct wattage and type marked on fixture label.
NOTE : DO NOT touch lamp with bare hands. Always use soft cloth or the plastic wrapping (if available) to handle the lamp. -
Re-install shroud and gasket and tighten shroud screws.
Frequently Asked Questions (FAQ)
Q: Can I use a lamp with wattage higher than what is specified on the
luminaire label?
A: No, it is important not to exceed the maximum wattage marked on the
luminaire label to prevent damage or hazards.
Q: How often should I clean the lens of the luminaire?
A: Regularly clean the lens to keep it free from dirt and debris to ensure
proper operation and prevent overheating. A maintenance schedule is
recommended for optimal performance.
Read User Manual Online (PDF format)
Read User Manual Online (PDF format) >>