X-BASS FR-182U Home Radio Instructions
- June 15, 2024
- X-BASS
Table of Contents
X-BASS FR-182U Home Radio
Product Information
Specifications
- Radio Model: FR-182U
- Lamp or Torch 2S.WUISTBC-HMINIJACK-5VIN
- Phone Jack
- USB Jack
- TF Jack
- PREV button
- PLAY/PAUSE button
- NEXT button
- MODE button
- Tuning button
- Power On/Off and Volume button
- Band Switch
- LED light (13/14)
- Tie Rod Antenna (15)
- Lifting Handle (16)
Accessories
- USB charging cable – 1
- 18650 800mAh battery – 1
FCC Statement
The product complies with Part 15 of the FCC Rules. Operation is subject to the following two conditions:
- This device may not cause harmful interference,
- this device must accept any interference received, including interference that may cause undesired operation.
Product Usage Instructions
Power On/Off and Volume Control
- To turn on the radio, press and hold the Power On/Off button (11). The radio will power on and the LED light will illuminate.
- To adjust the volume, rotate the Power On/Off and Volume buttons clockwise to increase the volume or counterclockwise to decrease the volume. To turn off the radio, press and hold the Power On/Off button again until the LED light turns off.
Tuning
- Use the Tuning button (10) to manually search for radio stations. Press the Tuning button briefly to increase or decrease the frequency in small increments.
- Press and hold the Tuning button to automatically scan for stations and stop at the next available station.
Mode Selection
- Press the Mode button (9) to cycle through different modes. The available modes include FM radio, AM radio, USB playback, TF card playback, and Bluetooth mode (if supported). The selected mode will be indicated by the LED light.
Playback Control
- Use the PLAY/PAUSE button (7) to start or pause playback in USB or TF card mode. Use the PREV (6) and NEXT (8) buttons to skip to the previous or next track.
LED Light and Torch
- The LED light (13/14) can be used as a torch. Press and hold the LED button for a few seconds to turn on the torch mode. Press and hold again to turn off the torch mode.
Antenna and Lifting Handle
- Extend the Tie Rod Antenna (15) for better radio signal reception. Use the Lifting Handle (16) for easy transportation of the radio.
FAQ
Q: How do I charge the radio?
- A: Connect one end of the USB charging cable to the USB Jack (4) on the radio and the other end to a power source such as a computer or a USB wall adapter.
- The LED light will indicate the charging status. Once fully charged, the LED light will turn off.
Q: How long does the battery last?
- A: The 18650 800mAh battery included with the radio provides approximately X hours of continuous playback, depending on the volume level and usage.
OVERVIEW
- LAMP OR TORCH
- USB-MINIJACK-5VIN
- PHONE JACK
- USB JACK
- TF JACK
- PREV
- PLAY/PAUSE
- NEXT
- MODE
- TUNING
- POWER ON/OFF AND VOLUME
- BAND SWITCH
- LED light
- TIE ROD ANTENNA
- LIFTING HANDLE
Operation instruction
- Place the 18650 battery or two AA1.5V batteries into a battery slot with the correct polarity and cover the battery.
- Turn on the power switch and volume control (11), adjust to the optimal volume, and then the power indicator light.
- Move band switch (12) to select FM, AM, and SW programs.
- Turn the tuner (10). Look at the frequency indicator window and dial the pointer to search for the radio program you want.
- When receiving the FM radio, please pull out the telescopic antenna (15) and keep it vertical to obtain a better receiving effect.
- When using the built-in magnetic antenna to receive an AM broadcast, the best reception effect can be obtained by rotating the direction of the radio.
- In order not to affect others, please insert the earphone into the headphone jack (3)(the speaker inside the radio is automatically disconnected), you can listen to the radio through the earphone.
- Please charge it after receiving it.
- When you don’t want to listen to the radio, turn it off by turning off the power switch and volume control (11).
Accessories
- USB charging cable *1
- 18650 800mAh battery *1
FCC Statement
This device complies with Part 15 of the FCC Rules. Operation is subject to the following two conditions:
- This device may not cause harmful interference.
- This device must accept any interference received, including interference that may cause undesired operation.
Changes or modifications not expressly approved by the party responsible for
compliance could void the user’s authority to operate the equipment.
Note: This equipment has been tested and found to comply with the limits
for a class B digital device, according to Part 15 of the FCC Rules. These
limits are designed to provide reasonable protection against harmful
interference in a residential installation.
This equipment generates uses and can radiate radio frequency energy and, if
not installed and used under the instructions, may cause harmful interference
to radio communications. However, there is no guarantee that interference will
not occur in a particular installation. if this equipment does cause harmful
interference to radio or television reception, which can be determined by
turning the equipment off and on, the user is encouraged to try to correct the
interference by one or more of the following measures:
- Reorient or relocate the receiving antenna.
- Increase the separation between the equipment and the receiver.
- Connect the equipment to an outlet on a circuit different from that to which the receiver is connected.
- Consult the dealer or an experienced radio/TV technician for help.
Read User Manual Online (PDF format)
Read User Manual Online (PDF format) >>