Petmate Le Bistro Portion Control Feeder User Manual

Petmate Le Bistro Portion Control Feeder User Manual

ASSEMBLY INSTRUCTIONS

To Assemble Hopper on Base

1. Align the hopper with the base.
2. Insert the hopper into the base.
3. Twist and lock into place.

To Assemble the Lid on the Hopper

1. Line up arrows on the hopper with arrows on the lid.
2. Place the lid on top of the hopper.
3. Twist and lock the lid into place.

To Assemble Bowl into Base

1. Insert the bowl into the base.
2. Lower bowl into the base connecting hooks into the base.
3. (Make sure Portion Control LeBistro® is placed on an even surface)
4. Close-up of Twist and Lock Hopper on Base.

SPECIFICATIONS

Programming

• Up to three different-sized Meals per 24 hours.
• Each Meal Serving is adjustable in 1/4 cup increments. Each Meal can be set from 1/4 cup to 3 cups.
• Default Meal Servings are Breakfast at 6:00 a.m. Lunch at noon. and Dinner at 6:00 p.m. All Meals are preset for 1/2 cup.

Dimensions

• 15.75″L x 10″W x 18″H (assembled)

Capacity

• Hopper (alone) will hold 8.55 Bs of a typical dry food variety.
• The base unit is fully loaded, bowl and food wheel will hold an additional 1.55 Ibs.

Wheel Dispensing Capacity

• 1/4 Cup increments or 1 Cup per complete revolution.

Overall Weight

• Weight: 3.5 Ibs (assembled without batteries and food).

Power

• Requires THREE “D” size batteries. Batteries NOT included.
• Use only alkaline batteries.
• The estimated life of one set of batteries is 6 months or less.
  Note: DC Power Converter is available as an accessory and can be ordered online at www.petmate.com

Types of Food

• Dry dog or cat food only.
• Do NOT use canned food. Do NOT use moist dog or cat food.
• Do NOT use semi-moist food. Do NOT use treats.

PROGRAMMING
READ ALL INSTRUCTIONS BEFORE OPERATING THE PRODUCT.

To Install Batteries

1. Turn the base upside down and remove the battery cover.
2. Install 3 new “D” cells, and alkaline batteries.
3. (Be sure to match positive and negative markings).
4. Replace the battery cover. Be sure to “snap” in place.

To Turn the Unit ON

1. Press the (-) side of the On/Off switch DOWN. (located on the bottom of the base)

2. Set the unit right side up. (LCD screen should be facing you)
   NOTE : The clock will flash “midnight” automatically.

3. Press the ENTER button to set the current time. First, the HOUR will be flashing.

4. Use the UP or DOWN arrow buttons to set the current HOUR. (until it is correct)
   NOTE : the clock will automatically change to A.M. or P.M. as you scroll through the hours.

5. Press the ENTER button again and the MINUTES will start flashing.

6. Use the UP or DOWN arrow buttons to set current MINUTES.

7. Press ENTER upon completion.
   NOTE: The clock will be set after setting minutes.

AUTOMATIC MODE
While setting the current time, if the programming is not completed the Portion Control LeBistro® waits until the current time is set and will not go into AUTOMATIC MODE.

SETTING ANY MEAL, MEAL TIME and MEAL SIZE

To Set Meal Selection

1. Press and Hold the ENTER button for 2 seconds. “MEALS” will flash.
2. Use the UP or DOWN arrow buttons to select the desired Meal to be programmed. (Breakfast, Lunch or Dinner will flash as the UP and DOWN arrows buttons are pressed)
3. Press the ENTER button after you select the Meal.
   • “Yes” will Flash. Press the ENTER if you want to set the meal time.
   • If you do not wish to set that meal time, press the DOWN arrow to select “No” and press ENTER.
   • Note : (if “No” is selected, press ENTER and the software takes you back to “MEALS”. Use the UP or DOWN arrows buttons to select the desired Meal to be programmed)

To set mealtime
After selecting the MEAL to be programmed and selecting “Yes”, the HOUR will flash.

1. Use the UP or DOWN arrow buttons to set Meal HOUR. (until it is correct)
   NOTE: that clock will automatically change to A.M. or P.M. as you scroll through the Hours.

2. Press the ENTER button again and the MINUTES will start flashing.

3. Use the UP or DOWN arrow buttons to set Meal MINUTES.

4. Press the Enter button when minutes are set.

5. The Menu will automatically take you to the “Meal Size” programming.

To Set Meal Size
After setting Meal Time, the “Meal Size” Menu will flash. (right side of the display)

1. Use the UP or DOWN arrow buttons to increase or decrease the amount of food to be dispensed. For example; to feed 1 cup meal size, press the UP arrow button until 4 bars are displayed.
2. Press Enter upon completion. NOTE: Each bar equals approximately 1/4 cup. The maximum meal size you may select is 3 cups.

To Set Other Meals
After any Meal has been programmed (inclusive of time and size) “MEALS” will flash and the Meals programmed will show on the screen.

1. The clock will display the current time.
2. REPEAT “Meal Selection” programming directions.
   NOTE: if you only wish to set 1 Meal, press ENTER while “MEALS” is flashing and the unit will go into AUTOMATIC MODE.

PROGRAMMING COMPLETE
After all meals are set:

1. Press ENTER
   NOTE: After programming of all meals is completed, press ENTER while “MEALS” is flashing and the unit will go into Automatic Mode. Meals Served

2. “SERVED” will show on the screen at all times. This indicates the number of Meals served. 1 digit equals 1 meal.

3. Meals served will go up to 99 and then reset at 00. To re-set the “SERVED” counter; press UP and DOWN Arrow buttons simultaneously and it will re-set to 00.

Manual Feed Option
Press and hold the UP Arrow button for 3 seconds.
NOTE: Food will be dispensed according to the first Meal set (i.e. breakfast is set at 1/2 cup, then food will be dispensed in 1/2 cup increments) Repeat if additional food is desired.

Replacement of Batteries/Power

• When the “LOW BATTERY” warning light is on OR before leaving for an extended period, replace the batteries.
• Refer to “TO INSTALL BATTERIES” for directions.
• Once NEW batteries are installed, turn the unit ON.
• Set the clock to the current time.
  IMPORTANT: Meal Programming is stored and will NOT need to be reprogrammed after batteries are replaced.

CLEANING

To Remove Bowl

1. Place fingers under the bowl and lift the Bowl.
2. Pull Bowl out horizontally removing it from the Base. (Bowl is top-rack dishwasher safe)
   NOTE: Lid and Hopper may be removed for cleaning. Hand clean with a soft cloth and hand dry.

Warning

• The base unit should not be submerged in water at any time, this may damage electronic components.
• Do not place the Base, Hopper or Lid in an automatic dishwasher.
• Allow parts to dry completely before adding new food.

Default Settings

1. While setting “Time” during the “Initial Set-up”; if the programming is not completed the Portion Control LeBistro® waits for you to finish.
2. While setting the “Time” during the “Change Time” is not completed and no button is depressed for 10 seconds the Portion Control LeBistro® abandons the change and goes into “Automatic Mode” and retains the previous “Time”.
3. While setting the “Meals” during the “Initial Set-Up” if no buttons are depressed for 10 seconds the Portion Control LeBistro® abandons the change and goes into “Automatic Mode” retaining the previous “Meals” settings.
4. While setting the “Meals” during the “Change Meals” no buttons are depressed for 10 seconds the Portion Control LeBistro® abandons the change and goes into “Automatic Mode” retaining the previous “Meals” settings.

CAUTIONS
Save these instructions for future reference. Read all instructions before operating the product.

• For indoor use only.
• For dry food use only. Works best with ?” diameter food.
• NOT recommended for puppies or kittens less than 7 months old.
• Do NOT use this feeder with puppies or kittens not able to reach the feeding dish.
• Do NOT use this feeder with puppies, kittens, dogs or cats with any physical disability.
• Intended for use with dogs or cats only.
• Do NOT allow small children to play with, in or around the feeder.
• Before leaving for an extended time, always replace batteries with 3 new, “D” size batteries.
• Do NOT immerse the control panel base in water.
• Do NOT place any foreign object in the feeder.
• Do NOT operate the feeder without the hopper and hopper lid securely in place.
• The feeder should be placed on a level surface.
• Do NOT disassemble the feeder other than the bowl, hopper, hopper lid and battery cover.
• Dispose of all packaging material properly. Some items may be packed in poly bags; these bags could cause suffocation; and keep away from children and pets.
• Check the low battery light frequently to be sure the feeder is dispensing properly.

WARNING

• Do NOT place anything on top of the feeder. The unit starts automatically. Keep Clear.
• The base unit should NOT be submerged in water at any time, this may damage electronic components.

TROUBLESHOOTING

1. If no display is showing, turn on the power. Refer to “To Turn Unit On” in programming instructions for specifications.

2. If the clock is flashing, the unit has lost its power and current time setting.

   • Reset the current time.
     NOTE: all previous meal programming does not need to be reset.

3. If “MEALS” is flashing, this indicates the unit did not completely deliver the full amount of food program for the meal.

   • Turn the unit off, empty the hopper and disassemble the hopper from the base.
   • Check for food jamming in the throat of the base.
   • Dislodge food jam.
   • Re-assemble unit.
   • Turn the unit on and reset the current time.

4. If the “Low Battery” indicator light is lit:

   • Turn the unit off.
   • Replace the batteries.
   • Turn the unit back on and set the current time.
     NOTE: Meal programming remains and does not need to be reprogrammed.

PET TRAINING TIPS
Getting Your Pet Used To The New Automatic Feeder Some pets may require a special adjustment period to acclimate to their new automatic feeder. If you determine that your dog or cat may require a special adjustment period, use the following steps:

1. Place the Portion Control LeBistro® next to your pet’s existing bowl or feeder. (Do not turn the power on)

2. Place food in the bowl of the Portion Control LeBistro® (only for a period to allow adjustment)

3. Keep food in the pet’s current bowl. (only for some time to allow adjustment)

4. Once you have observed your pet eating from the Portion Control LeBistro®, remove their old feeding dish and begin using the Portion Control LeBistro®.
   NOTE: Adjustment time for the pet could be as short as a day or as long as a couple of weeks, depending on your pet’s personality.

5. You may also want to introduce your pet to the Portion Control LeBistro® by placing small treats in the bowl.

REPLACEMENT PARTS
AC Adapters for the U.S. and Europe are available at www.petmate.com
Replacement Bowls are available at www.petmate.com
Replacement Hoppers are available at www.petmate.com

WARRANTY

1 Year Limited
COUNTRY OF ORIGIN
All parts are made and assembled in China.
All packaging is made and printed in China.

P. O. Box 1246
Arlington, Texas USA, 76004-1246
1-877-PETMATE
www.petmate.com
PET 4804

Download PDF:Petmate Le Bistro Portion Control Feeder User Manual

Read User Manual Online (PDF format)

Read User Manual Online (PDF format)  >>

Download This Manual (PDF format)

Download this manual  >>