PHILIPS BRP715 LED Solar Street Light Owner’s Manual
- June 29, 2024
- Philips
Table of Contents
PHILIPS BRP715 LED Solar Street Light
Product Specifications
Type Number| Flux(lm)| Battery Type| Battery Parameter| Solar Board Type| PV
Power| Solar Board Voltage| Remote Type| CCT| Operating Temperature
---|---|---|---|---|---|---|---|---|---
BRP715 LED50 CW Solar| 5000lm| LFP| 12Ah/12.8V| MONO| 25W| 18V| Remote| 5700K|
-10°C to -55°C
Product Using Instructions
Type-A Universal Bracket Installation Procedure
- Step 1: Check lamp appearance and functionality. Mount bracket to a lamp with provided screws and tools.
- Step 2: Insert the lamp into a pole and secure it with screws and nuts using appropriate tools.
- Step 3: Adjust the solar panel angle by loosening and tightening the screws on the universal support. The recommended installation angle is 15 degrees.
- Step 4: Adjust the light source angle with a screwdriver. Open the switch button to activate.
Frequently Asked Questions
Q: What is the recommended operating temperature range for the product?
A: The operating temperature ranges from -10°C to -55°C.
Q: What tools are required for installation?
A: Tools required include a 6MM hex wrench, M8*20 screws, M8 spring washer, 5MM inner hexagon wrench, 17mm outer hexagon wrench, 14MM hex wrench, and a screwdriver or Phillips screwdriver.
Product Installation Instruction
Dimension
- Product Size (Unit: mm)
- BRP715 LED50 CW Solar
- BRP715 LED70 CW Solar
- BRP715 LED90 CW Solar
- BRP715 LED120 CW Solar
- BRP715 LED90 CW Solar
- BRP715 LED50 CW Solar Pro
- BRP715 LED70 CW Solar Pro
- BRP715 LED90 CW Solar Pro
- BRP715 LED120 CW Solar Pro
- BRP715 LED180 CW Solar Pro
Installation Instructions
Installation Procedure for Type-A Universal Bracket
- Step1: A: Open the package to check whether the appearance of the lamp is intact. Click the switch button to test whether the lamp is normal.
- B: Mount the bracket to the lamp and tighten the screws with a torque of 170kGF. cm (Prepare accessories and tools :6MM hex wrench,M8*20 screws 4PCS, M8 spring washer 4PCS)
- Step 2: A: Put the lamp into the pole, tighten the M10 screw with a torque of 250kGF. cm.
- B: tighten the M10 nut with a torque of 150kGF. cm (preparation tools inner hexagon wrench,17mm outer hexagon wrench)
- Step 3: Loosen the screws on the universal support and adjust the irradiation Angle of the solar panel.
- Tighten the screws with a torque of 600kGF. cm and adjust the Angle of -90*-+90. It is recommended that the installation Angle be 15 degrees (preparation tool:14MM hex wrench).
- Step 4: Adjust the irradiation Angle of the light source with a screwdriver or a Phillips screwdriver. Tighten the screw with a torque of 8 kgF. cm, and then open the switch button
Installation Procedure for Type-B Post-Top Bracket
- Open the package and check whether the appearance of lamp is in good condition. Click the switch button to test whether the lamp is working.
- Prepare installation tools and accessories: 8mm hexagonal wrench, socket bracket, M10 * 20 screw 4pcs. Assemble the socket bracket to the lamp body, As shown in the picture. (The screw tightening torque is 250 kg. cm.)
- Prepare installation tools and accessories: 8m hexagonal wrench, screw M10*25 6pcs, and insert the lamp into the lamp pole, as shown in the picture.
- Note that the installation of the lamp needs to be adjusted vertically to the ground. (The screw tightening torque is 250 kg. cm )
- Preparation tool: Cross-head screwdriver. Loosen the light source module screw, then adjust the light source module to a suitable lighting angle, as shown in the figure,(The screw tightening torque is 8kgf. cm.), and then turn on the switch button.
Working Way and Wiring Diagram
- During the day, the solar light shines on the solar panel, generating electric energy, which is controlled by the controller to charge the battery.
- In the evening, the solar light darkens, the controller stops charging, and then drives the LED light to turn on. If there is an induction function, the light becomes bright when the induction and the light becomes dark when there is no induction.
- Wiring sequence: First connect COM-WB, then the load, then the battery, and finally the solar panel.
- COM-WB
- Load/LED
- Battery
- Solar Panel
Note:
- The above sensing distance is based on the installation height of 6m, opposite to the sensor, the adult pedestrian speed is about 0.5-1m/s, and the vehicle speed is about 3-5km/h;
- The sizes and speeds of people or objects are different, then the sensing distance varies the faster speed results in less sensing distance;
- The sensor is optimally designed for movement detection of people or objects. So, under some specific circumstances, minor actions will not trigger the sensor detection;
- The parameters of the luminaire can’t be reset in the field.
Indicator
Operating Mode
Working mode shall be subject to specific order requirements
Operating Mode
Working mode shall be subject to specific order requirements
Warning:
- Solar panels are fragile, so please do not scratch or bump when installed. Scratches, dirt, and shelter on the surface will affect the power generation efficiency of solar panels.
- Solar lamp installation, such as in the northern hemisphere solar panel should face in the northern hemisphere, such as the southern hemisphere should face south.
- The product must be charged every 3 months when idle. If it needs to be transported or stored for a long time, it is necessary to timely check, charge, and record; otherwise, the battery will be damaged. Charging method: In sunny conditions, open the lamp switch, the solar panel is placed facing the sun, continuously charging for 1-2 days.
- Note: use a multimeter to test the voltage at both ends of the battery is more than 13V (12.8V LiFePO4) / 26V(25.6V LiFePO4)
- Installation location shall be away from WIFI, omnidirectional antennas for mobile communications, small base stations for telecommunications, TV antennas, etc. A signal source too close may be disabled. the dimming functions.
- The luminaire should not be installed on vibrating surfaces, otherwise, the sensor is easy to be triggered by mistake.
- Warning:
- The luminaire shaking may cause the sensor to be triggered by mistake.
- The dimming function of the luminaire might be effected by the objects with vibration in its sensing area. The lamp should not be installed on the surface of vibration, and the lamp should not be covered.
- (e.g. trees or leaves), otherwise, the sensor may be triggered or not triggered by mistake.
- The product has a good penetration effect on plastic and wood. Avoid metal shielding around the antenna, which will reflect and block the microwave and affect the actual induction effect.
- Walls, glass, and ceramics will bring reflection and penetration attenuation of electromagnetic waves, and reduce the sensing distance of the sensor. The thicker the material is, the more serious the attenuation is.
- The movement of animals and objects within the sensing range may cause the light to turn on, which is a normal phenomenon.
- In the electromagnetic wave emitted by microwave sensors in the practical application environment, the different reflectivity of obstacles will lead to different induction ranges, which is a normal phenomenon.
- Please turn on the power switch of the fixture before use, and test whether it is functional before installation.
- Ensure that the power switch is on when working normally. Please test whether the lamps are charged and discharged normally before installation (the solar panel is charged by sunlight and the lamp is off; Solar panels block sunlight, do not charge, light)
- View the entire installation guide. Do not disassemble by non-professional technicians or under the guidance of professional technicians.
- Do not place the product in water or fire, as there may be explosion risk.
- The product can withstand a typhoon of grade 12, a storm above may cause damage to the product
- Disposal at end of life: Battery to be removed by professional
- The product contains lithium batteries, please follow the air transport regulations when shipping, should be regarded as flammable and explosive goods, and storage should be separated from other items to avoid damage.
- Charging and discharging requirements: Charging temperature is 0-45, and discharging temperature is -10-60℃. Storage temperature: -10~60℃.
- The installation distance, both transverse and longitudinal, should be greater than 15m.
- If the installation distance is too close, individual lamps may be misfit.
- The final product interpretation authority of our company.
Read User Manual Online (PDF format)
Read User Manual Online (PDF format) >>