SMARTEH LPC-2.DB2 Longo Programmable Controller Debug Module User Manual
- June 29, 2024
- SMARTEH
Table of Contents
SMARTEH LPC-2.DB2 Longo Programmable Controller Debug Module
FAQ
Frequently Asked Questions
- Q: Can the LPC-2.DB2 debug module be used with other controller models?
- A: The LPC-2.DB2 is specifically designed for use with LPC-2.main modules and certain operator terminals as listed in the description. It is recommended to refer to the product manual for compatibility information.
- Q: What should I do if the diagnostic LEDs show abnormal patterns?
- A: If the diagnostic LEDs display unusual patterns or do not indicate normal operation, check the connections and ensure proper installation according to the provided connection schemes in the manual.
STANDARDS AND PROVISIONS
Standards, recommendations, regulations and provisions of the country in which the devices will operate, must be considered while planning and setting up electrical devices. Work on 100 .. 240 V AC network is allowed for authorized personnel only.
DANGER WARNINGS: Devices or modules must be protected from moisture, dirt and damage during transport, storing and operation.
WARRANTY CONDITIONS
WARRANTY CONDITIONS: For all modules LONGO LPC-2 – if no modifications are performed upon and are correctly connected by authorized personnel – in consideration of maximum allowed connecting power, warranty of 24 months is valid from the date of sale to the end buyer, but not more than 36 months after delivery from Smarteh. In case of claims within warranty time, which are basedon material malfunctions the producer offers free replacement.
The method of return of malfunctioned module, together with description, can be arranged with our authorized representative. Warranty does not include damage due to transport or because of unconsidered corresponding regulations of the country, where the module is installed.
This device must be connected properly by the provided connection scheme in
this manual. Misconnections may result in device damage, fire or personal
injury.
Hazardous voltage in the device can cause electric shock and may result in
personal injury or death.
NEVER SERVICE THIS PRODUCT YOURSELF!
This device must not be installed in the systems critical for life (e.g. medical devices, aircrafts, etc.).
If the device is used in a manner not specified by the manufacturer, the
degree of protection provided by the equipment may be impaired.
Waste electrical and electronic equipment (WEEE) must be collected separately!
LONGO LPC-2 complies to the following standards:
- EMC: EN 61000-6-3:2007 + A1:2011, EN 61000-6-1:2007, EN 61000-3- 2:2006 + A1:2009 + A2: 2009, EN 61000-3-3:2013
- LVD: IEC 61010-1:2010 (3rd Ed.), IEC 61010-2-201:2013 (1st Ed.)
Smarteh d.o.o. operates a policy of continuous development.
Therefore we reserve the right to make changes and improvements to any of the
products described in this manual without any prior notice.
MANUFACTURER:
- SMARTEH d.o.o.
- Poljubinj 114 5220 Tolmin Slovenia
ABBREVIATIONS
Sorted by order of appearance in document:
- LED: Light emitting diode
DESCRIPTION
LPC-2.DB2 debug module is used for debugging LPC-2.main modules LPC-2.MC9, LPC-2.MM1, LPC-2.MM2, LPC-2.MM3 and operator terminals LPC-3.GOT.111, LPC-3.GOT.131, LPC-3.GOT.112, LPC-3.GOT.012, LPC-3.GOT.002.
FEATURES
INSTALLATION
Connection scheme example
Table 2: K1
Internal BUS | Data transfer | Connection to controller |
---|
Table 3: K2
K2.1 | N.C. | Not connected |
---|---|---|
K2.2 | GND | Ground |
K2.3 | N.C. | Not connected |
K2.4 | Rx ·¬ | Data receive input |
K2.5 | Tx ·® | Data send output |
K2.6 | N.C. | Not connected |
Table 4: K3
K3.1 | VCC | Power supply input |
---|---|---|
K3.2 | D- | Data – |
K3.3 | D+ | Data + |
K3.4
| ****
ID
| May be N/C, GND or used as an attached device presence indicator
| | (tied to GND with resistor)
K3.5| GND| Ground
Table 5: Adapter connectors
Table 6: LEDs
Mounting instructions
- Dimensions in milimeters.
WARNING: All connections, module attachments and assembling must be done while module is not connected to the main power supply.
Mounting instructions for debugging purpose:
- Switch off main power supply.
- Mount LPC-2.DB2 module to the provided place inside an electrical panel (DIN EN50022-35 rail mounting).
- Mount other LPC-2 modules (if required). Mount each module to the DIN rail first, then attach modules together through K1 and K2 connectors.
- Make connections as show in connection schemes.
- Blue LED1 should turn on.
Dismount in reverse order. For mounting/dismounting modules to/from DIN rail a free space of at least one module must be left on the DIN rail.
NOTE: LPC-2 main module should be powered separately from other electrical appliance connected to LPC-2 system. Signal wires must be installed separately from power and high voltage wires in accordance with general industry electrical installation standard.
Module labeling
Label Description:
- XXX-N.ZZZ – full product name.
- XXX-N – Product family
- ZZZ – product
- P/N: AAABBBCCDDDEEE – part number.
- AAA – general code for product family,
- BBB – short product name,
- CCDDD – sequence code,
- CC – year of code opening,
- DDD – derivation code,
- EEE – version code (reserved for future HW and/or SW firmware upgrades).
- S/N: SSS-RR-YYXXXXXXXXX – serial number.
- SSS – short product name,
- RR – user code (test procedure, e.g. Smarteh person xxx),
- YY – year,
- XXXXXXXXX – current stack number.
- D/C: WW/YY – date code.
- WW – week and
- YY – year of production.
Optional
- MAC
- Symbols
- WAMP
- Other
TECHNICAL SPECIFICATIONS
_ Table 7: _Technical specifications
- Power supply from USB
- Power consumption 0.5 W
- Connection type K2 RJ-12 6/4
- Connection type K3 mini B type
- Dimensions (L x W x H) 90 x 18 x 60 mm
- Weight 40 g
- Ambient temperature 0 to 50 °C
- Ambient humidity max. 95 %, no condensation
- Maximum altitude 2000 m
- Mounting position vertical
- Transport and storage temperature -20 to 60 °C
- Pollution degree 2
- Protection class IP 30
SPARE PARTS
For ordering spare parts following Part Numbers should be used:
CHANGES
The following table describes all the changes to the document.
Date | V. | Description |
---|---|---|
05.06.24 | 1 | The initial version, issued as LPC-2.DB2 UserManual. |
CONTACT
- SMARTEH d.o.o. / Poljubinj 114 5220 Tolmin Slovenia
- Tel: +386(0) 388 44 00
- e-mail: info@smarteh.si
- www.smarteh.si
Written by: SMARTEH d.o.o.
Copyright © 2024, SMARTEH d.o.o.
Read User Manual Online (PDF format)
Read User Manual Online (PDF format) >>