SMARTEH LBT-1 Bluetooth Mesh Triac Output Module User Manual
- June 1, 2024
- SMARTEH
Table of Contents
SMARTEH LBT-1 Bluetooth Mesh Triac Output Module
Specifications
- Product Name: Longo Bluetooth Products LBT-1.DO4 Bluetooth Mesh Triac output module
- Version: 2
- Manufacturer: SMARTEH d.o.o.
- Input Voltage: 100-240V AC
Product Usage Instructions
Safety Precautions
Ensure authorized personnel handle electrical devices operating on a
100-240V AC network. Protect devices from moisture, dirt, and damage during
transport, storage, and operation.
Setup and Installation
The LBT-1.DO4 Bluetooth Mesh Triac output module operates with the
LBT-1.GWx Modbus RTU Bluetooth Mesh gateway on the same Bluetooth Mesh
network. Refer to the device connection diagram for proper setup.
Operation Parameters
The operation parameters for the triac output module are detailed in Table
2. Ensure proper configuration of registers for executing commands,
destination addresses, vendor ID, model ID, virtual address index, application
key index, and option code.
ABBREVIATIONS
- LED Light Emitted Diode
- PLC Programmable Logic Controller
- PC Personal Computer
- OpCode Message Option Code
DESCRIPTION
LBT-1.DO4 Bluetooth Mesh two triac output module is designed to be used as a shades or curtains motor control module with RMS current and voltage measuring possibility. The module can operate with a wide range of AC voltages. It can be placed inside the 60mm diameter flush mounting box. It can also be placed close to shades or curtains motor. Switch input is provided to have the possibility of manually switching On and Off the two triac outputs. This input can detect 50/60 HZ for triac 1 control and 25/30 HZ for triac 2 control. Two- position push button switch with an appropriate diode as 1N4007 should be connected to the switch input line wire as shown in Figure 4. Only one triac output, triac output 1 or triac output 2, can operate at the time.
LBT-1.DO4 Bluetooth Mesh two triac output module can only operate with Smarteh LBT-1.GWx Modbus RTU Bluetooth Mesh gateway connected to the same Bluetooth Mesh network. LBT-1.GWx Modbus RTU gateway is connected to the main control device as Smarteh LPC-3.GOT.012 7″ PLC-based Touch panel, any other PLC or any PC with Modbus RTU communication. Besides Smarteh Bluetooth Mesh devices, other standard Bluetooth Mesh devices can be integrated into above mentioned Bluetooth Mesh network. More than a hundred Bluetooth Mesh devices can be provisioned and can operate in a single Bluetooth Mesh network.
FEATURES
Table 1: Technical data
- Communication standard: Bluetooth Mesh is a low-power wireless mesh protocol and allows device-to-device communication and device-to-main control device communication.
- Radiofrequency: 2.4 GHz
- Radio range for direct connection: < 30 m, depending on application and building. By using Bluetooth Mesh topology, much bigger distances can be achieved.
- Power supply: 90 .. 264 V AC
- Ambient temperature: 0 .. 40 °C
- Storage temperature: -20 .. 60 °C
- Status indicators: red and green LED
- 2 x Triac output, 0.7 A continuous per output/ 1 A pulsing per output
- RMS current and voltage measurement, power consumption measurement
- Switch digital input
- Mounting in flush mounting box
OPERATION
LBT-1.DO4 Bluetooth Mesh Triac output module can only operate with Smarteh LBT-1.GWx Modbus RTU Bluetooth Mesh gateway while provisioned to the same Bluetooth Mesh network.
Other triac output module functions
Factory reset: This function will delete all Bluetooth Mesh network parameters stored on LBT-1.DO4 triac output module and will restore to the conditions of the initial programming, ready for provisioning. See Table 5 for more information.
Operation parameters
- LBT-1.DO4 Bluetooth Mesh Triac output module accepts a set of operation codes as specified in below tables 2 to 4.
- LBT -1.DO4 Bluetooth Mesh output module is communicating with the main control device as Smarteh LPC-3.GOT.012 via Smarteh LBT-1.GWx Modbus RTU Bluetooth Mesh gateway.
All communication between the main control devices is LPC-3.GOT.012 or similar is performed by using Modbus RTU communication. Individual Bluetooth Mesh node configuration data should be observed by using network provisioning tool.
- Observed from the network provisioning tool
- User-defined parameters, refer to the option code table
INSTALLATION
Figure 5: LBT-1.DO4 module
Mounting instructions
Figure 6 : Housing dimensions
Dimensions in millimeters.
Figure 7: Mounting in flush mounting box
-
Switching Off the main power supply.
-
Mount the module up to the provided place and wire the module according to the connection scheme in Figure 4. Two position push button switches and the appropriate diode as 1N4007 should be connected to the LBT-1.DO4 module switch input line wire
as shown in Figure 4. -
Switching On the main power supply.
-
After a few seconds Green or Red LED starts to blink, please see the flowchart above for details.
-
If the module is not provisioned Red LED will blink 3x, the provisioning procedure has to be started. Contact the producer for more details*.
-
Once provisioning is finished, the module will continue with the normal mode of operation and this will be indicated as Green LED blinking once per 10 seconds.
Dismount in reverse order.
NOTE: Smarteh Bluetooth Mesh products are added and connected to a Bluetooth Mesh network by using standard provisioning and configuration mobile app tools such as nRF Mesh or similar. Please contact the producer for more detailed information.
SYSTEM OPERATION
LBT-1.DO4 Bluetooth Mesh triac output module can switch power to two triac outputs, usually to power shade or curtain motors, based on 50/60Hz or 25/30Hz voltage present on module switch input or based on Bluetooth Mash command. Only one triac output can operate at a time.
Interference warning
Common sources of unwanted interference are devices that generate high-
frequency signals. These are typically computers, audio and video systems,
electronics transformers, power supplies and various ballasts. The distance of
the LBT-1.DO4 two triac output modules to the above-mentioned devices should
be at least 0.5m or greater.
WARNING
- To protect plants, systems, machines and networks against cyber threats, necessary to implement and continuously maintain up-to-date security concepts.
- You are responsible for preventing unauthorized access to your plants, systems, machines and networks and they are allowed to be connected to the Internet only, when security measures like firewalls, network segmentation, … are in place.
- We strongly recommend the updates and usage of the latest version. Usage of versions that are no longer supported may increase the possibility of cyber threats.
TECHNICAL SPECIFICATIONS
- Power supply 90 .. 264 V AC, 50/60 Hz
- Max. power consumption 1.5 W
- Fuse 1 A (T-slow), 250 V
- Load voltage Same as power supply voltage
- Max. continuous load current per output 0.7 A
- Max. load current per output, 50% On / 50% Off, pulse <100 s 1 A
- Connection type Screw type connectors for stranded wire 0.75 to 2.5 mm2
- RF communication interval Minimum 0.5 s
- Dimensions (L x W x H) 53 x 38 x 25 mm
- Weight 40 g
- Ambient temperature 0 to 40 °C
- Ambient humidity Max. 95 %, no condensation
- Maximum altitude 2000 m
- Mounting position Any
- Transport and storage temperature -20 to 60 °C
- Pollution degree 2
- Overvoltage category II
- Electrical equipment Class II (double insulation)
- Protection class IP 10
MODULE LABELING
Figure 10: Label
Label (sample):
Label description:
- XXX-N.ZZZ – full product name,
- XXX-N – product family,
- ZZZ.UUU – product,
- P/N: AAABBBCCDDDEEE – part number,
- AAA – general code for product family,
- BBB – short product name,
- CCDDD – sequence code,
- CC – year of code opening,
- DDD – derivation code,
- EEE – version code (reserved for future HW and/or SW firmware upgrades),
- S/N: SSS-RR-YYXXXXXXXXX – serial number,
- SSS – short product name,
- RR – user code (test procedure, e.g. Smarteh person xxx),
- YY – year,
- XXXXXXXXX – current stack number,
- D/C: WW/YY – date code,
- WW – week and,
- YY – year of production.
Optional:
- MAC,
- Symbols,
- WAMP,
- Other.
CHANGES
The following table describes all the changes to the document.
FAQ
Frequently Asked Questions
- Q: Can the LBT-1?DO4 module operates independently without the Bluetooth Mesh gateway?
- ‘A: No, the LBT-1.DO4 module requires the Smarteh LBT-1.GWx Modbus RTU Bluetooth Mesh gateway for operation within the Bluetooth Mesh network.
- Q: What should I do if the device is exposed to moisture or dirt?
- A: If the device is exposed to moisture or dirt, disconnect it from power immediately and allow it to dry completely before use. Do not attempt to operate the device until it is completely dry to prevent damage.
Read User Manual Online (PDF format)
Read User Manual Online (PDF format) >>