ZHIJIA EXFQS12B44G Smart HD IP Camera User Guide

ZHIJIA EXFQS12B44G Smart HD IP Camera

About this product

• This manual is only a guide for related products and may differ from the actual product, please refer to the actual product. Due to product version upgrades or other needs, this manual may be updated without further notice!
• This guide applies to various types of battery cameras. Some of the illustrations are based on battery cameras.

RF Exposure Statement

To maintain compliance with FCC’s RF Exposure guidelines, This equipment should be installed and operated with a minimum distance of 20cm from the radiator of your body. This device and its an conjunction sian cost antenna operation transmitter.

Packing list

• Battery camera xt
• Base x1 mounting guide sticker x1
• Charging cable xi
• 3M Glue xi
• Quick Start Guide x1
• Screw package x1

Product sales configuration in different
Please refer to the actual product

• Camera x1
• Charging cable xi
• Solar panel x1(*option)
• Mounting sticker x1 Quick Start Guide xt Screw package x1

The instructions of LED light :

• The green light flashes for 2s and goes out The device is powered on and connected to the network
• Greenlight + red light is always on: The camera is being previewed remotely (privacy light)
• Green light is always on: The device is connected to the network or awakened Green light flashes continuously: Upgrading
• Green light flashes continuously and slowly: Charging
• Red light flashes 3 times quickly. Power off ” Red light is always on Low battery
• The traffic light is always off: In standby
• Button operation for single button model:
• Press the reset button and hold for 3s: Turn on
• Press the reset button 3 times continuously: Power off
• Press the reset button and hold it for 5s in the power-on state: Reset
• Button operation for the Two-button model:
• Press and hold the on-off button for 2s when shutting down: Turn on
• Press and hold the on-off button for 2s when powering on: Power off
• Press and hold the reset button for 3a: reset

Boot up and Charging instructions

Boot up

1. When remote view by connecting to the router and direct connection method, please boot the device after inserting the SD card. When using by pairing to the wireless NVR, please make sure the memory(SD card, HDD etc.) of the wireless NVR is ready.
2. During use, if it is found that the APP pushes a low battery message or the camera has a low battery warning indicator, you need to charge the camera, as shown in the figure.
3. Dial the camera switch to “ON” to turn on.
4. Connect the camera to the solar panel.
   Reminder: If the device does not turn on after turning the switch to ON, please insert the solar panel connection cable and place the solar panel in sunlight for 1-2 hours to charge, or plug in a household charger to charge before trying again.

Note:

• Please use the original battery, and the camera or the original charger to charge the battery.
• Using other batteries will result in an inaccurate power display and may damage the camera.
• Please charge the battery at room temperature. If the temperature is too low or too high, the charging time will be extended, the battery will be damaged and the battery life will be affected.

FCC

FCC Warning Statement
Changes or modifications not expressly approved by the party responsible for compliance could void the user’s authority to operate the equipment. This equipment has been tested and found to comply with the limits for a Class B digital device, under Part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation. This equipment generates uses and can radiate radio frequency energy and, it not installed and used by the Instructions, may cause hantul interference to radio communications. However, there is no guarantee that interference will not occur in a particular installation. it this equipment does cause harmful interference to radio or television reception, which can be determined by turning the equipment off and on, the user is encouraged to try to correct the interference by one or more of the following measures:

• Reorient or relocate the receiving antenna
• Increase the separation between the equipment and the receiver.
• Connect the equipment to an outlet on a circuit different from that to which the recelver is connected.
• Consult the dealer or an experienced radio/TV technician for help.

This device complies with Part 15 of the FCC Rules.
Operation Is subject to the following two conditions:

1. this device may not cause harmful interference,
2. this device must accept any interference received,

Including interference that may cause undesired operation.

RF Exposure Statement
To maintain compliance with FCC’S RF Exposure guidelines, This equipment should be installed and operated with a minimum distance of 20cm from the radiator of your body. This device and Its antenna(s) must not be co- located or operation in conjunction with any other antenna or transmitter.

Please read the Quick Start Guide carefully before using the product and keep it properly.
Reminder: Please charge the device for 2 hours before using it.

SCANNER

Read User Manual Online (PDF format)

Read User Manual Online (PDF format)  >>

Download This Manual (PDF format)

Download this manual  >>