YAMAHA NS-333 Bass Reflex Bookshelf Speakers User Manual
- June 13, 2024
- Yamaha
Table of Contents
YAMAHA NS-333 Bass Reflex Bookshelf Speakers
PRECAUTIONS
Read these precautions carefully before using your speakers.
PLACING THE SPEAKERS
Place the speakers on a sturdy, vibration-free surface, on a well-built stand.
Using 2ch stereo speakers
Better stereo images will be obtained when the speakers are slightly angled in towards the listeners.
Using as main speakers in a multi-channel system
Position the speakers on both sides of the TV. The positioning of speakers is important because it controls the whole sound quality of a multi-channel system. Set up the speakers on the basis of your listening position by following the owner’s manual supplied with your amplifier.
Using as front or rear effect speakers
Mount the speakers on a wall or place the speakers on a shelf. Determine the best position by following the owner’s manual supplied with your amplifier.
Note: This speaker features a magnetically shielded design, but there is still a chance that placing it too close to a TV set might impair picture color. Should this happen, move the speaker away from the TV set.
To mount the speaker on a wall by using the attached mounting bracket
Fasten screws into a firm wall or wall support as shown in the figure, and hang the holes of the mounting bracket on the protruding screws.
- Make sure that the screws are securely caught by the narrow parts of the holes.
WARNING
- This speaker weighs 5.5 kg (12 lbs. 2 oz.). Do not mount it on thin plywood or a wall with soft surface material. If mounted, the screws may come out of the flimsy surface and the speaker may fall. This damages the speaker or causes personal injury.
- Do not install the speaker on a wall with nails, adhesives, or any other unstable hardware. Long-term use and vibrations may cause it to fall.
- To avoid accidents resulting from tripping over loose speaker cables, fix them to the wall.
CONNECTIONS TO YOUR AMPLIFIER
Before making connections, make sure that the amplifier is switched off.
Connections
- Connect the screw-type input terminals at the rear of the speaker to the speaker output terminals of the amplifier (or receiver) with the speaker cable.
- Connect the (+) terminals on the amplifier (or receiver) and the speaker using one side of the cable. Connect the (–) terminals on both components using the other side of the cable.
- Connect the speaker to the center terminals of the amplifier (or receiver) making sure not to reverse the polarity (+, –). If the speaker is connected with reversed polarity, the sound will be unnatural and lack bass.
How to Connect:
- Remove the insulation coating at the extremity of each speaker cable by twisting the coating off.
- Loosen the terminal knob.
- Insert the bare wire.
- Tighten the knob and secure the cable. Test the firmness of the connection by pulling lightly on the cable at the terminal.
Note: Do not let the bare speaker wires touch each other to avoid damaging the speaker or the amplifier, or both of them.
Using a Banana Plug
- Tighten the terminal knob.
- Simply insert the banana plug into the terminal.
REMOVING THE FRONT COVER
The front cover is fastened to the enclosure at four points and can be removed if desired. To remove the cover, hold on to both sides and slowly pull straight away from the speaker. To reattach, line up the four pegs on the inside surface of the cover with the four corresponding holes on the speaker and push gently.
Note: When the cover is removed, take care not to touch the speaker units with your hands or to exert excessive force with tools.
SPECIFICATIONS
- Type:
- 2-way bass reflex speaker system
- Magnetic shielding type
- Driver:
- 13 cm (5″) cone woofer
- 2.5 cm (1″) dome tweeter
- Frequency Response: 60 Hz – 35 kHz
- Nominal Impedance: 6 ohms
- Nominal Input Power: 60 W
- Maximum Input Power: 150 W
- Sensitivity: 87 dB/2.83 V/m
- Crossover Frequency: 3 kHz
- Dimensions (W x H x D): 200 mm x 320 mm x 213 mm (7.9″x 12.6″ x 8.4″)
- Weight: 5.5 kg (12 lbs. 2 oz.)
- Specifications are subject to change without notice due to product improvements.
- Care should be taken not to exceed the input power values noted above.
Information for users on the collection and disposal of old equipment:
- This symbol on the products, packaging, and/or accompanying documents means that used electrical and electronic products should not be mixed with general household waste.
- For proper treatment, recovery, and recycling of old products, please take them to applicable collection points, in accordance with your national legislation.
- By disposing of these products correctly, you will help to save valuable resources and prevent any potential negative effects on human health and the environment that could otherwise arise from inappropriate waste handling.
- For more information about the collection and recycling of old products, please contact your local municipality, your waste disposal service, or the point of sale where you purchased the items.
- For business users in the European Union:
- If you wish to discard electrical and electronic equipment, please contact your dealer or supplier for further information.
- Information on Disposal in other Countries outside the European Union:
- This symbol is only valid in the European Union. If you wish to discard these items, please contact your local authorities or dealer and ask for the correct method of disposal.
FAQs
What is the driver complement of the Yamaha NS-333 bookshelf speakers?
The Yamaha NS-333 speakers feature a 5\
What is the input power rating for these speakers?
These speakers have a nominal power rating of 60 watts and can handle up to 150 watts of music power.
What is the frequency response of the Yamaha NS-333 speakers?
The frequency response of these speakers is from 65 Hz to 35 kHz, providing a wide range of audio frequencies.
What is the sensitivity rating of these speakers?
The sensitivity rating is 87dB/2.83v/1m, indicating their efficiency in converting power into sound.
Can these speakers be used for home theater applications?
Yes, the Yamaha NS-333 speaker system is designed specifically for home theater applications and can be used for main or surround channels.
Are these speakers magnetically shielded?
Yes, these speakers are magnetically shielded, allowing them to be placed near a TV or video monitor without affecting the picture quality.
What is the cabinet design of these speakers?
The speakers are enclosed in an Elliptical Form cabinet with a high-gloss black piano finish, providing solid construction with minimal sound diffraction.
Do these speakers come with a warranty?
Yes, they come with a Yamaha Warranty, ensuring their quality and performance.
What is included in the box when you purchase these speakers?
The box includes the Yamaha NS-333 5in 2-way 150W Bookshelf Speakers and 2x speakers.
Can these speakers be wall-mounted, or are they designed for tabletop use only?
The Yamaha NS-333 speakers are designed for tabletop use. They do not have built-in wall-mounting brackets, so wall mounting may require additional hardware and customization.
Are these speakers compatible with amplifiers or receivers with 4-ohm impedance ratings?
The Yamaha NS-333 speakers have an impedance rating of 6 ohms. While they may work with amplifiers or receivers that support 4-ohm speakers, it's essential to check the compatibility and power handling capabilities of your amplifier to ensure optimal performance.
Do these speakers require a subwoofer for low-frequency audio, or can they handle bass effectively on their own?
While the Yamaha NS-333 speakers have a built-in 5\
Download This PDF Link: YAMAHA NS-333 Bass Reflex Bookshelf Speakers User Manual_
Read User Manual Online (PDF format)
Read User Manual Online (PDF format) >>