HBEZON BA-0013MC-L Rectangular Iron Small LED Mirror Installation Guide

June 28, 2024
HBEZON

HBEZON BA-0013MC-L Rectangular Iron Small LED Mirror

Specifications:

  • Dimensions : 20 in. (W) x 28 in. (H) x 4.8 in. (D)
  • Alternate Dimensions: 17-1/2 in. (W) x 22-1/4 in. (H) x 3-1/2 in. (D)

Product Usage Instructions

Installation:
SURFACE MOUNT INSTRUCTION:

  1. Measure and mark the back mounting holes on the wall.
  2. Unpack the LED medicine mirror and prepare tools needed.
  3. Drill holes and put in the plastic expansion bolt.
  4. Draw a horizontal line connecting the marked location. The line should be level. Adjust to level if necessary.
  5. Connect hardwire to power line. Make sure the power is off (Voltage: AC110-120V, 50/60Hz).
  6. Attach the cabinet to the wall with mounting screws from the hardware pack.

Maintenance:
Wipe clean with a soft damp cloth. Apply glass cleaner to cloth and do not apply directly to mirror. Never use abrasive cleaners asthese could damage the finish or exposed LED strip.

Important Safety Instructions:

  • Use the furnishing only for its intended use as described inthe instructions.
  • Do not use attachments not recommended by the manufacturer.
  • Never drop or insert any object into any opening.
  • Do not use outdoors.

Electric Connections:
WARNING: All wiring should be done by a qualified licensed electrician. Requires 120 VAC 20 Amp GFI protected Circuit.

Hardware and Tools (Tools not included):

  • Power Drill
  • Mallet
  • Tape Measure
  • Safety Goggles
  • 1/4″ & 1/8″ Drill Bits
  • Pencil
  • Level

IMPORTANT SAFETY INSTRUCTIONS

When using an electrical furnishing, basic precautions should always be followed ,including the following:

WARNING:

  • To reduce the risk of burns,fire,electric shock or injury to persons.
  • Use this furnishing only for its intended use as described in these instructions. Do not use attachments not recommended by the manufacturer. Never drop or insert any object into any opening.Do not use outdoors.
  • Risk of electric shock.Connect this furnishing to a properly grounded circuit only. See grounding instructions.

ELECTRIC CONNECTIONS

ALL WIRING SHOULD BE DONE BY A QUALIFIED LICENCED ELECTRICIAN.

WARNING:

  • Shut off power before wiring.
  • Requires 120 VAC 20 Amp GFI protected Circuit.

GROUNDING INSTRUCTIONS:

CAUTION: This product must be connected to a grounded metal permanent wiring system or an equipment-grounding conductor must be run with the circuit conductors and connected to the equipment grounding terminal or lead on the product.

WARNING: An Electrical option mirror must be wired to a 20 Amp GFI(Ground Fault Interrupter) protected circuit when used in bathrooms and all other locations required by the National Electric Code.

HOW TO CONNECTIONS

HBEZON-BA-0013MC-L-Rectangular-Iron-Small-LED-Mirror-fig-
\(1\)

HARDWARE AND TOOLS ( Tools not included)

HBEZON-BA-0013MC-L-Rectangular-Iron-Small-LED-Mirror-fig-
\(2\)

INSTALLATION INSTRUCTIONS

Please read carefully and save these instructions
Don’t discard any of the packaging until you are sure that you have all of the parts and the fitings Make sure power to the junction box is off before commencing installation.

IMPORTANT

  1. Unpack LED cabinet. DO NOT lay cabinet on tiled or concrete surface prior to installation Cabinet must be on protected surface to prevent chipping of the corners
  2. Care must be taken before drilling pilot holes to avoid any existing wiring or pipe work that may be concealed.
  3. A certified electrician must perform all work.The mirror must be connected to a GFI

MAINTENANCE
Wipe clean with a soft damp cloth. Apply glass cleaner to cloth and do not apply directly to mirror Never use abrasive cleaners as these could damage the finish or exposed LEDstrip 2

INSTALLATION
Please refer to below surface mount or recess mount method.

SURFACE MOUNT INSTRUCTION

  1. Unpack the LED medicine mirror and prepare tools needed.
  2. Draw horizontal line connecting the marked location. The line should be level. Adjust to level if necessary.HBEZON-BA-0013MC-L-Rectangular-Iron-Small-LED-Mirror-fig- \(3\)
  3. Drill holes,and put in the plastic expansion bolt.HBEZON-BA-0013MC-L-Rectangular-Iron-Small-LED-Mirror-fig- \(4\)
  4. Connect hardwire to power line. Make sure the power off(Voltage:AC110-12V,50/60Hz)HBEZON-BA-0013MC-L-Rectangular-Iron-Small-LED-Mirror-fig- \(5\)
  5. Attach the cabinet to the wall with mountin screws from the hardware pack.

HBEZON-BA-0013MC-L-Rectangular-Iron-Small-LED-Mirror-fig-
\(6\)

RECESS MOUNT INSTRUCTIONS
NOTE : Rough opening is not an exact measurement. The extra space allows cabinet to be inserted into the opening. Add shims to level and tighten space if necessary. Additional framing might be required.

Rough Wall Opening

HBEZON-BA-0013MC-L-Rectangular-Iron-Small-LED-Mirror-fig-
\(7\)

  1. NOTE:
    • Before cutting the rough opening,check for pipes, electrical cables, or heating ducts. If it is required to remove part of stud, make sure that the wall is not a load bearing wall. Prepare the opening in the wall for the cabinet body. Make sure that there is support on both sides of the opening to attach the cabinet body, as shown.
    • The cabinet height should be a minimum 2 in. above faucet.
  2. Connect hardwire to power line. Make sure the power off (Voltage: AC110-12V,50/60Hz)HBEZON-BA-0013MC-L-Rectangular-Iron-Small-LED-Mirror-fig- \(9\)
  3. Position the cabinet body in the rough wall opening. Make sure that the cabinet body flange covers the wall opening uniformly. Secure both sides of the cabinet body to the wall supports using mounting screws.

NOTE : The cabinet body must be level for the door to work properly.

INTRODUCTION OF TOUCH FUNCTION

HBEZON-BA-0013MC-L-Rectangular-Iron-Small-LED-Mirror-fig-
\(11\)HBEZON-BA-0013MC-L
-Rectangular-Iron-Small-LED-Mirror-fig- \(12\)

DIMENSION

  1. Width
  2. Height
  3. Depth

Unit : Inch

Note : All dimensions & specifications are approximate and subject to change without notice.

Customer Service:
For any questions or queries regarding our products, please contact our support team:

FAQ

Q: Can I use abrasive cleaners to clean the mirror?
A: No, never use abrasive cleaners as these could damage the finish or exposed LED strip.

Q: What voltage is required for connecting the hardware?
A: Make sure the power is off and connect to a voltage of AC110-120V, 50/60Hz.

Read User Manual Online (PDF format)

Read User Manual Online (PDF format)  >>

Download This Manual (PDF format)

Download this manual  >>

Related Manuals