U-LINE ULASHP15SOLID Stainless Accessory Panel Installation Guide

Table of Contents

Accessory Numbers
- ULASHP15SOLID – 15 (38cm) Solid Door, Dimensions: 14.872 x 29.90 x .751
- ULASHP15FRAME – 15 (38cm) Frame Door, Dimensions: 14.872 x 29.90 x .751
- ULASHP18SOLID – 18 (45cm) Solid Door, Dimensions: 17.464 x 29.90 x .751
- ULASHP18FRAME – 18 (45cm) Frame Door, Dimensions: 17.464 x 29.90 x .751
- ULASHP24SOLID – 24 (60cm) Solid Door, Dimensions: 23.364 x 29.90 x .751
- ULASHP24FRAME – 24 (60cm) Frame Door, Dimensions: 23.364 x 29.90 x .751
- ULASHP24DWR – 24 (60cm) Drawer (2 Panels), Dimensions: 23.364 x 14.858 x .751

Open the door/drawer completely.
Starting at the corner, pull the gasket away from the door/drawer and remove it.
Lay the gasket down on a flat surface.
If the frame panel includes a pre-installed black insert, remove the protective foil on the top and bottom sides if applicable.
Align the pilot holes by placing the panel on the top corner edge of the door/drawer. Align the top of the panel with the highest point of the door/drawer. Align Panel Against Door Edge.
Have a second person hold the panel in place or secure it with a clamp.
Locate the provided screws (#8-321-1/4 (32 mm)) and place one screw in each of the pilot holes (6 screws for door panels, 4 screws for drawer panels).
Using a #2 Phillips screwdriver, secure the screws. Do not over-tighten.
Reinstall the gasket beginning at the corners.

Accessory #	Description
ULASHP15SOLID	15” (38cm) Solid Door

14.872” x 29.90” x .751”

ULASHP15FRAME| 15” (38cm) Frame Door

14.872” x 29.90” x .751”

ULASHP18SOLID| 18” (45cm) Solid Door

17.464” x 29.90” x .751”

ULASHP18FRAME| 18” (45cm) Frame Door

17.464” x 29.90” x .751”

ULASHP24SOLID| 24” (60cm) Solid Door

23.364” x 29.90” x .751”

ULASHP24FRAME| 24” (60cm) Frame Door

23.364” x 29.90” x .751”

ULASHP24DWR| 24” (60cm) Drawer (2 Panels)

23.364” x 14.858” x .751”

Open the door/drawer completely.
Starting at a corner, pull the gasket away from the door/drawer and remove it.
Upon removal, lay the gasket down on a flat surface.
Certain frame panels include a pre-installed black insert. Remove the protective foil on the top and bottom sides if applicable.
Align the pilot holes by placing the panel on the top corner edge of the door/drawer.
Have a second person hold the panel in place or secure it with a clamp.
Locate the 6 #8-321-1/4 (32 mm) screws provided with your panel. (Drawer panels use only 4 screws per panel)
Using a #2 Phillips screwdriver, place 1 screw in each of the 6 pilot holes and secure. Do not over-tighten.
Reinstall the gasket beginning at the corners.

30436 Rev E 6/2024

Q: How many screws should I use for door panels?
- A: Six screws (#8-321-1/4) should be used for door panels.
Q: What screwdriver should I use for securing the screws?
- A: Use a #2 Phillips screwdriver to secure the screws.
Q: Should I over-tighten the screws during installation?
- A: No, do not over-tighten the screws during installation to avoid damaging the panel or door/drawer.