Pisen TP-C24 3 in 1 Night Light Wireless Charging Stand User Manual

Pisen TP-C24 3 in 1 Night Light Wireless Charging Stand

Product Information

Specifications

• Model: XYZ-2000
• Dimensions: 10in x 5in x 3in
• Weight: 2 lbs
• Power: 120V AC
• Capacity: 1 liter

Product Usage Instructions

We appreciate your purchase of the PISEN wireless charger. Please read these instructions carefully to ensure safe and smooth operation, and keep this instruction properly for future reference. The product is used for charging mobile phones or digital products which can be charged in a wireless manner.

Technical specifications

Schematic Diagram of Product Interface

Note:

• The product also supports magnetic wireless charging for the iPhone 12-15 series, wireless charging for mobile phones supporting the Qi standard, and wireless charging for Apple Watch and headsets.
• Confirm whether your device can be charged in wireless manner before use!

Description of indicator status

Setup

1. Place the product on a flat, stable surface near a power outlet.
2. Ensure the power switch is in the OFF position before plugging in.
3. Connect the product to the power source using the provided power cord.
4. Fill the reservoir with water up to the maximum capacity indicated.

Note: When the product charges the headset/watch, the power of the main coil will be automatically reduced.

Instructions for use of night light:
Touch the button of the night light to turn on the night light. The brightness of night light can be adjusted between three levels: low, medium and high. When the button is pressed continuously, the night light is turned on, and then switched into the low, medium, high brightness status in turn, finally turned off. The user can press and hold the button for 3 seconds to turn off the night light.

Precautions

• Do not place the product on carpets, heaters, textile materials or expose it in direct sunlight.
• Do not bump, squeeze, disassemble or puncture the product.
• Do not place the product in a high temperature and humid environment.
• Do not put the product into fire, water or corrosive liquid.
• Please use the product with power adapters of PISEN or other legal brands.
• Do not put the product on flammable substances (beds and blankets) when charging.
• In the case of any expansion or other defects and faults of the product, stop using the product immediately and contact your distributor.
• The following persons (including children) are only allowed to use the product under the supervision and guideline of professionals to ensure their safety: those with degraded physical or mental abilities, and those with insufficient knowledge of the product and lack of operating experience. Be sure to supervise the whole use process when children use the product to ensure their safety.
• In order to ensure the long-term service of wireless charging, do not put magnetic metal objects such as magnetic cards, bank cards and keys on the product when charging.
• Try to avoid full-load service, so as not to affect the charging efficiency.

Operation

1. Turn on the power switch and select your desired settings using the control panel.
2. The product will start heating the water. Wait for the indicator light to signal that it’s ready.
3. Place your items for heating or steaming in the designated compartment.
4. Close the lid securely to start the heating process.

Cleaning and Maintenance

1. Unplug the product and allow it to cool down before cleaning.
2. Wipe the interior and exterior surfaces with a damp cloth and mild detergent.
3. Rinse thoroughly and dry before storing.
4. Regularly describe the product as per the instructions in the manual to maintain performance.

FCC Statement

This device complies with part 15 and part 18 of the FCC Rules. Operation is

Subject To the following two conditions:

• This device may not cause harmful interference, and
• this device must accept any interference received, including interference that may cause undesired operation.

Changes or modifications not explicitly approved by the party responsible for compliance could void the user’s authority to operate this equipment.

Note: this equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to part 15 and part 18 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation. This equipment generates, uses and candidate radio frequency energy and, if not installed and used in accordance with the instructions, may cause harmful interference to radio communications. However, there is no guarantee that interference will not occur in a particular installation.

If this equipment does cause harmful interference to radio or television reception, which can be determined by turning the equipment off and on, the user is encouraged to try to correct the interference by one or more of the following measures:

• Reorient or relocate the receiving antenna.
• Increase the separation between the equipment and the receiver.
• Connect the equipment to an outlet on a circuit different from that to which the receiver is connected.
• Consult the dealer or an experienced radio/TV technician for help.

The equipment complies with FCC radiation exposure limits set forth for an uncontrolled environment. During the operation of device, a distance of 15 cm surrounding the device and 20 cm above the top surface of the device must be respected.

Frequently Asked Questions

Q: How often should I describe the product?
A: It is recommended to describe the product every 1-2 months, depending on usage frequency and water hardness in your area.

Q: Can I use the product without water?
A: No, always ensure there is an adequate amount of water in the reservoir before operating the product to avoid damage.

Read User Manual Online (PDF format)

Read User Manual Online (PDF format)  >>

Download This Manual (PDF format)

Download this manual  >>