PISEN TS-OPS04 Wilderness 600 Outdoor Power Station 600W User Manual

Wilderness 600
Outdoor Power Station 600W
User Manual

Read this USER Manual thoroughly before use is a MUST for your safety and the safety of others

Specification

24000mAh/22.5V 540Wh
Output| Refer to the product body
Input| Refer to the product body
Working Status| LCD Display
Discharge Temperature| -10℃~40℃
Net Weight| About7.4Kg
Size| 303230191mm
Charge time| 6~8 Hours with adapter，Fast charge 4~6 hours with PD &adapter

Note: The charge time is measured by Pisen LAB, and the actual charge time may vary depending on the type of charger used and the environmental impact.

Product Appearance

1. LCD Display
2. Power Switch
3. USB-A Output
4. USB Button
5. Type-C Output
6. DC Button
7. DC Input| 8. DC 12V Output
9. Car Charger Port
10. AC Output
11. AC Button
12. LED Lamp
13. LED SOC
14. LED On-off
---|---

LCD Display

| Battery status
/Fault code| Displays the percentage of remaining battery during normal use. Display fault code when fault occurs.
---|---|---
AC
DC
USB| Function| Working status of the interface.
| Output power| The left number shows the current discharge power.
| input power| The right number shows the current charge power.
| Residual charge
and discharge time| Displays the battery life of the power station before it needs to be recharged.
| Discharging| Power station is discharging to device.
| Charging| Power station is charging.

Charging

• This power station has an internal rechargeable lithium battery. Please charge this power station at your first use.
• When the battery drains to 10%，the battery level indicator on the Lcd Display will flash slowly, please charge the power station in time.
• If the battery drains to 10% after constant 600W power consumption at AC output ports, it’s recommended to wait for 30 minutes for the device to cool down its internal temperature before charging it.

Charging status:

| |
---|---|---
Charging| Fully Charged| Low Battery

OPtion.1.Charge with the AC Adapter
Plug one end of the AC Adapter provided to any socket, and the other end to the DC Input port of the power station to charge. It will take 6-8 hours to get the device fully charged.

Option2. Charge with a PD charger
Plug one end of the PD charger provided to any socket, and the other end to the Type-C1 input port of the power station to charge. It will take 6-8 hours to get the device fully charged.

Notes:

• You can charge with the AC adapter provided and a PD charger together to achieve fast charging which will cost only 4-6 hours to get the device fully charged.
• This device can supply power to external devices via all output ports when it’s being charged.
• Please do not touch the adapter /PD charger when charging.
• Please unplug the AC adapter/ PD charger in time after the charging is completed.

Option 3.Charge with the Car Charger
Plug one end of the Car charger to the Cigarette Lighter of your Vechicie, and the other end to the DC Input of the poower station. Start the engine of your vehicle to automatically charge the power station. It will take 6-7 hours to get the device fully charged.

Notes:

• Please make sure that the output voltage of the Cigarette Lighter reaches 12V/24V when charging with the car charger。
• Before charging the power station with the Car Charger , please start the energine of youe vehicle to ensure a steady power supply.

Option 4.Charge with a Solar Panel
Step1:Place your solar panel where it can collect as much direct sunlight as possible.
Step2: Connect the DC Output of the solar panel to the DC Input of the power station.

Notes:

• A solar panel with 60-100W power supply is recommended to charge this device.
• The charging time varies from different loaction, temperature and weather etc.
• When charging ,please keep your portable power staion away from heat and direct sunlight in order to extend its life span.

POWER ON/Off Button

2.1.Press and hold the “POWER“ button for 3s to wake up the LCD display and the power station starts to work.Then you can check the battery level and more.
2.2.Press and hold the ”POWER” button for 3S to turn off all outputs ports and product.

Note:
When LCD Display and indicators are off , it means the device powers off. During the charging and discharging process, the LCD screen will automatically turn off after 5 minutes, while the machine is still working, click the “POWER” button to turn on.

Connect to External Devices

3.1.DC output
(1).When the product is powered on, press and hold the “DC” button for 3 S to activate power supply to DC Out puts this moment the DC button indicator and LCD screen are on, it indicates that the DC is ready to supply power to external devices.

3.2. USB Output

1. When the product is powered on, press and hold the “USB” button for 3S to activate power supply to USB Outputs”，this moment the USB button indicator and LCD screen are on, it indicates that the USB is ready to supply power to external devices.
2. Connect the devices to the power station with the USB-A or Type-C.(USB-A ports support QC, FCP, AFC, Apple2.4A and other fast charging protocols, Type-C ports support PD3.0, QC, FCP, AFC and other protocols, of which Type-C1 supports PD100W
   bidirectional fast charging)

3.3.AC output

1. When the product is powered on, press and hold the “AC” button for 3S to activate power supply to AC Outputs.
2. Connect the devices to the power station with the AC connector.

Opterate the Flashlight

Press the flashlight button once to turn on the low
brightness.| Press the button twice to turn on the high brightness.| Press the button the third time, then the flashlight will deliver SOS signal.| Press the button the fourth time to turn off the
flashlight.

4.1.The Separation Function
The flashlight has a magnetic detachable design built-in strong magnetic magnet, which can be attached to any paramagnetic metal object according to the needs of use.
4.2.Charge The Flashlight
When the battery of flashlight drains out, please follow the below steps in time to get it charged:
When it’s in flashlight compartment, press and hold any button for 3S on the power station;
When it’s outside the power station , put it back into the flashlight compartmant correctly by lining up contact pins or use a USB-C charger to get it chargerd
4.3. A Guide to Battery Indicator of Flashlight
Charging: Flashlight is red.
Fully charged/Not charged :Indicator light off.

Smart Drive

• When the load power exceeds the rated output power, the Smart Drive mode will be activated. The power station still supplies power to loads when identifying that the power required by the loads is greater than the rated output power. In this way, you can use more types of electrical equipment with remarkable experience.
• The Smart Drive function is ON by default.

Please pay attention to the following when using the Smart Drive function:

1. The power station is not designed for grid-connected generation.
2. The Smart Drive mode is not available during charging.
3. The Smart Drive mode is specially designed for resistive loads and not for all electrical equipment except these for heating purpose. It is recommended to be used with heat-generating electrical equipment, such as electric hair drier, electric heating kettle, electric warming oven, electric saw, induction cooker, etc. The Smart Drive mode is not applicable to electric equipment with voltage protection function (for example, precision instruments, etc.). Sufficient tests before use are necessary to judge if the Smart Drive mode applies to the equipment.

Short Circuit/Overload Protection

• Short circuit protection is the protectin against excessive current beyond the acceptable current rating of the power statin and it reacts instantly. AS soon as an overcurrent is detected, the power station trips and cuts off the circuit.
• Overload protection is the protectiion against a continuous overcurrent. As soon as a continuous overcurrent is detected, the power station cuts off the circuit as well.
• When a short circuit or an overload occurs, please remove the connected equipment and cable as soon as possible to cut off the circuit.

Maintenance And Care

• If the product is not used for a long time, please completely trun off the power station and store it in a dry place.
• The battery may be affected by low-temperature environments, so it’s suggested to use the product within the operation temperature. Otherwise ,the product may not work normally.
• Make sure the product has enough power before use.
• When the power station has a high temperature or a short circuit, immediately cut off the power station and carefully check whether there is excess power.
• Only use PISEN and a regular brand of AC adapter or PD adapter to charge the outdoor power station.

Battery

• The product has a built-in lithium battery. If it is shelved for a long time, please recharge the product every 6 months。
• Do not attempt to repair the ptoduct by yourself, which minght cause overheating, fire or injury.
• Do not let the water run into the product or spill any water onto the product.
• The battery in your power staion should be serviced or recycled by an authorized service provider, and must be recycled or disposed of separatedly from the household waste.

Troubleshooting Guide

• Please make sure to press and hold the DC outputs on/off button for 3s to activate power supply to DC outputs or press and hold the USB outputs On/off button for 3s to activate power supply to USB outputs and type-c output.
• Make sure the power station has enough power.

Why can’t charge my device via the AC outputs?|

• Please make sure to press and hold the AC outputs On/off button for 3s to activate power supply to AC outputs.
• Make sure the power station has enough power.
• Make sure the AC power outputss power does not exceed its threshold of 600W.

Is this power station allowed in airplanes?| According to the regulation of the international Civil Aviation Organization, the lithium-Ion battery under 100 Wh is acceptable with carry -on only. However, the power station reaches 621.6Wh which is forbidden for transport in airplanes.
Can the power station supply power to ecternal devices when ti’s charging?| It’s feasible for DC outputs, AC outpus, usb outputs and Type-C output. However, to extend thebattery life, it,s not recommended to do so.
What’s the specification for a solar panel that is compatible with this power station?| A solar panel with an 10V~25V max power supply and a 6530 DC connector is recommended to charge the power station.

Fault Code

port power, USB/PD input power
Inverter over temperature protection| E05| IGBT heat sink
Inverter overload protection| E07| Inverter power
Battery charging low temperature protection| E08| R186/R188 resistors at both ends
Battery charging over temperature protection| E09| R186/R188 resistors at both ends
Battery discharge low temperature protection| E10| R186/R188 resistors at both ends
Battery discharge over temperature protection| E11| R186/R188 resistors at both ends
Battery overvoltage protection| E12| AFE
Battery undervoltage protection| E13| AFE
Cell overvoltage protection| E14| AFE
Cell undervoltage protection| E15| AFE
Current overcurrent protection| E16| AFE
Charging failure| E17| AFE
DC overcurrent protection| E18| Cigar lighter circuit input positive current R191/U12B,USB,PD PositivecurrentR192,U23
MOS over temperature protection| E19| RT1,Charging, car charger MOS tube/inductor
Fault| Fault Code| Describe
---|---|---
BMS charging over temperature protection| E20| R176 resistors at both ends
BMS discharge over temperature protection| E21| R176 resistors at both ends
BMS MOS over temperature protection| E22| R180 resistors at both ends
BMS cell overvoltage protection| E23| AFE
BMS total voltage overvoltage protection| E24| AFE
BMS cell undervoltage protection| E25| AFE
BMS total voltage undervoltage protection| E26| AFE
BMS discharge short circuit protection| E27| AFE
BMS discharge overcurrent protection| E28| AFE
BMS charging overcurrent protection| E29| AFE
BMS ambient over temperature protection| E30| R176 resistors at both ends
BMS environmental cryogenic protection| E31| R176 resistors at both ends
BMS temperature acquisition failure| E32| AFE
BMS voltage acquisition failure| E33| AFE
BMS discharge MOS failure| E34| C95 Level at both ends
BMS charging MOS failure| E35| C87 Level at both ends
BMS cell imbalance| E36| AFE

Important Safety Information

This product is designed for supplying power to a piece of equipment that has suitable power requirements. Other uses may result in injury to the operator or damage to the product and other properties.

Please make sure anyone who operates the power station reads this manual or receives proper instructions before use.

• Do not let children operate pr play wiith the power station without parental supervision. This is an ecletric product, not a toy!
• Keep the power station away from metal objects including coins ,keys,hair-pins,etc.,to avoid a short circuit.
• Only use the ORIGNAL cables and power adapters provided by Pisen. Accessories from unauthorized stores may cause injury or damage.
• Do not disassemble or repair the product by yourself. Please directly contact pisen support if any futher assistance is required.
• NEVER use the power cable or adapter that party damaged; otherwise, you may get an electric shock when operating.
• Chanrge the product a ventilated place and do not block the air vents.
• Do not dispose of the product in fire, water or other liquids to avoud the risk of explosion. Be sure to be obey local recycling ordinance requirements.
• Use or stor the product in a dry place to avoid the high humid condition.
• Do not use the product outdoors whaen it’s raining or snowing, which may lead to the risk of electircal shock
• Do not place any heavy objects or strong impact on the product.
• Do not cover the product with cloth, paper or any other materials when the power station is working.
• Do not expose the product to any fire, heat source, direct sunlight or high temperature thar exceeds 60℃(140℉）,which may result in an explosion.
• We assume no liabliity or responsibility for any fire, explosion or eletrical shock caused by improper operation.

Packing List

Manufacturer: Guangdong PISEN Electronics Co.,Ltd
In case of other questions or problems or request for supports,
please contact: Support@PisenGroup.com

References

• ICUC Subscriber Line Number 3 ICUC Subscriber Number 3 ICUC Directory Listings ending in 3

Read User Manual Online (PDF format)

Read User Manual Online (PDF format)  >>

Download This Manual (PDF format)

Download this manual  >>