PISEN BHD-TW6 Wireless Earphone User Manual

PISEN BHD-TW6 Wireless Earphone

Specification parameters

Type- C Charging cablel
User Manuall
Lanyard*l

The above data is sourced from the PISEN Laboratory, white actual parameters may vary with product or other factors.

Kind reminders

Thank you for buying the Pl Ptus. Please read this manual carefully to ensure safe and satisfactory operation, and properly keep it for future reference.

1. The specifications and external appearance of this product are subject to change and improvement at any time
2. The design and specifications are subject to change without prior notice
3. Please clean the earbud with dry cloth frequently.

Product diagram

Use instructions for earbuds

1. Power-on
   Open the lid of charging case, and the earbuds will be automatically powered on.

2. Power-off
   Put the earphones in to the charging case and close the lid, the earphoneswi11tumoffandcharge (The earphones will automatically shut down after 5 minutes of no pairing status.)

3. Earbuds pairing
   in the case of sufficient power,open the cover of the charging case, and the left and right earphones will automatically tum on and complete the pairing.

4. Connecting to a mobile phone

   • Dual earphone connection to phone Open the charging case. the earphones enter pairing mode. Search for the pairing name “Pisen Pl Plus” on the phone, Click to connect, and after successful connection, a prompt sound will be played (Supports single earphone connection)
   • Automatically connect to phone When there is a pairing record, open the charging case cover and the earphones will automatically reconnect to the most recently connected phone

5. Intelligent dual connection
   First, tum on the Bluetooth of device A and connect the Bluetooth earphones, then tum off the Bluetooth of device A:, Then tum on the Bluetooth of device B, search and connect the Bluetooth earphones, and then connect device back to the Bluetooth earphones to achieve intelligent dual connection.

Instructions for earbuds touch controls

Music play mode

Phone-call mode

Game mode

Touch the function key of any earphone 4 times to open game mode, repeat the operation to close 1t

Voice assistant

When the earphones are connected to the phone, long press any earphone function button for 3 seconds, hear a beep sound, and then release it to activate the voice control function. Repeat the operation to exit.

Factory reset

When the earphones are not connected to the phone and in single ear mode, four clicks on any earphone touch function button will restore the earphones to factory settings and turn them off.

Left and right earphone connections When the earphones are not connected to the device, double-click on the left and right  at the sametime, and then press andholdfor2secondstomterconnectthelehandrightearphones, and then enter pairing mode.

LED indicator state

Charging indicator

• Using a charging case to charge the earphones:
  Place the earphones into the charging case and close the cover. The blue indicator light on the charging case remains on and goes off after charging is completed.

• Low battery warning for charging case:
  Put the headphones into the charging case, and the blue indicator light on the charging case will flash, indicating that the charging case has low battery and needs to be charged in a timely mane

• Charging the charging case: Charging: White indicator light flashing. Fully charged: The white indicator light remains on.

Warning:

1. Please store and use the product at normal temperature;
2. Do not expose the product to the rain or humid environment;
3. Do not throw or toss the product, so as to avoid damage;
4. Do not disassemble, repair, or modify the product by yourself;
5. The product contains a non-replaceable lithium battery, so be sure not to dispose of it randomly, put it in fire, or expose it to direct sunlight, so as to avoid hazards;
6. Please dispose of the battery according to local regulations and recycle it whenever possible, and be sure not to dispose of it as the domestic waste, so as to avoid environmental pollution.

Kind reminders:

1. To avoid the hearing damage, please keep the volume at a moderate level and avoid listening to music at a high volume for a long time, as it may result in permanent hearing damage or deafness.
2. Please refrain from making phone calls or using earbuds while driving, cycling, crossing roads, or engaging in situations that require focused attention.
3. When watching videos with earbuds, the audio and video may get out of sync slightly.
4. If the earbuds are not used for a long time, please fully charge them at least once a month to extend the battery life.
5. If the earbuds are still connected or not charged after being put into the charging case, please wipe the stain on the charging contacts of earbuds to ensure good charging contact.
6. The output voltage and current of charger shall not exceed 5V /1 A. If their specified values are exceeded, the product will be seriously damaged and the warranty will be voided.

FCC Warning:

This device complies with part 1 5 of the FCC rules. Operation is subject to the following two conditions: (1) this device may not cause harmful interference, and (2) this device must accept any interference received, including interference that may cause undesired operation. Changes or modifications not expressly approved by the party responsible for compliance could void the user’s authority to operate the equipment.
NOTE: This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation. This equipment generates uses and can radiate radio frequency energy and, if not installed and used in accordance with the instructions, may cause harmful interference to radio communications. However, there is no guarantee that interference will not occur in a particular installation. If this equipment does cause harmful interference to radio or television reception. which can be determined by turning the equipment off and on, the user is encouraged to try to correct the interference by one or more of the following measures:

• Reorient or relocate the receiving antenna.
• Increase the separation between the equipment and receiver.
• Connect the equipment into an outlet on a circuit different from that to which the receiver is connected.
• Consult the dealer or an experienced radio/TV technician for help. The device has been evaluated to meet general RF exposure requirement. The device can be used in portable exposure condition without restriction.

Customer Support

Name and company of U.S. agent: FCC US Agent. LLC
Physical U.S. address of agent: 3722 Illinois Avenue. Saint Charles. IL,
60174, USA
FRN of U.S. agent: 0033402884
Email address of U.S. agent: Support@FCCUSAgent.com
PATECH.,JSC
Address: B26+27. Quarter B. Hoang Cau Str, 0 Cho Dua Ward, Dong
Da Dist. Ha Noi. Viet Nam
Tel: 0084 -24 66616999
Yarn En Tees (PH)
Address: 7th Floor Unit 3, 1464 Antonio Rivera St. Tondo Manila
Tel: 09816089999
Import by: AOCE INFORMATION TECHNOLOGY
Add: 61 rue de Lyon 75012 Paris Contact( Name.email.tel): Johnson.wang.aoce- service@outlook.com
Tel:+49-163 l 014 128
Design By Pisen Made in China
Manufacturer: GUANGDONG PISEN ELECTRONICS CO .• LTD.
Address:No.9, Qinfu l st street, Jintang Industrial Park,Henggang
Town, Longgang Distrist, Shenzhen. P. R China
The brand belongs to GUANGDONG PISEN ELECTRONICS

 For FAQs and more help information, please visit https://en.pisengroup.com
 Contact: support@pisengroup.com

Read User Manual Online (PDF format)

Read User Manual Online (PDF format)  >>

Download This Manual (PDF format)

Download this manual  >>