SY HS14E-18G Splitter With Down Scaler User Manual

June 26, 2024
SY

User Manual
SY-HS14E-18G
1×4 HDMI 2.0 (18Gbps) Splitter With
4K → 1080p Scaling

HS14E-18G Splitter With Down Scaler

Can use mix of 4K and 1080P displays Active HDMI cables and AOC supported
This HDMI 2.0 1×4 splitter supports all HDMI signals up to 18Gbps (4K60 4:4:4) with HDR, EDID and CEC pass-through. It can split the HDMI input signal to a maximum of four separate display devices.
Each output can automatically scale down a 4K input video to 1080p to ensure compatibility with 1080p display. Hence accommodating a mix of 4K and 1080p displays.
This HDMI splitter will be useful for any situation where the HDMI signal needs to be displayed at multiple locations and can handle all HDMI resolutions, including the growing 18G sector.

Features

  • 18G 4K60 4:4:4 maximum HDMI input resolution
  • Automatically down scales 4K HDMI to 1080p per output as required
  • Each HDMI output connector can power Active HDMI cables (Max. 500mA)
  • EDID management
  • HDCP management – Supports HDCP 1.4, 2.2, 2.3 and Cascade Mode
  • Supports HDR
  • Provides CEC pass-through

Panel Descriptions

Front

SY HS14E 18G Splitter With Down Scaler-

Name Description
Power LED RED when powered
IN Blue when HDMI input signal present
1 ~ 4 Blue when HDMI present on the respective output
EDID EDID / HDCP Options
SERVICE Micro-USB for service use only

Rear

SY HS14E 18G Splitter With Down Scaler- Rear

Name Description
HDMI IN HDMI Input connector from HDMI source
HDMI 1 ~ HDMI 4 HDMI Output connectors to HDMI display devices
12V DC 12V DC PSU Input connector

System Connection

The SY-HD14E-18G can be located anywhere in the HDMI cabling, the following diagram is only an installation example. The larger screens represent 4K displays and the smaller screens represent 1080p displays.

SY HS14E 18G Splitter With Down Scaler- Connection

Connecting to the SY-HS14E-18G

  1. Connect the HDMI source device to HDMI IN.
  2. Connect any required HDMI display devices to HDMI 1 to HDMI 4 connectors.
  3. Connect the 12V DC PSU to the 12V input connector.
  4.  If needed, set the EDID switches to the desired setting.

Red Power LED
The red front panel power LED will be lit when the splitter is powered.
Blue Signal LEDs
The five blue signal LEDs indicate the presence of the HDMI signal at the respective input and outputs connectors.
Switch Settings
The four-way DIP switch provides EDID options on switches 1 to 3 and HDCP options on switch 4, as described in the following sections.
EDID Settings
Switch positions 1 to 3 provide EDID options in the following table. A 0 indicates that the switch is in its down position and 1 indicates that the switch is in the up position.

SW1 SW2 SW3 Video Resolution Audio Format
0 0 0 EDID Bypass – with priority given to the connected

output

with the highest number

0| 0| 1| 1080p| LPCM 2.0ch
0| 1| 0| 1080p| LPCM 7.1ch
0| 1| 1| 1080p| DTS/Dolby 5.1ch
1| 0| 0| 3840×2160 30Hz HDR| LPCM 7.1ch
1| 0| 1| 3840×2160 30Hz HDR| DTS/Dolby 5.1ch
1| 1| 0| 3840×2160 60Hz HDR| LPCM 7.1ch
1| 1| 1| 3840×2160 60Hz HDR| DTS/Dolby 5.1ch

HDCP Setting
Switch position 4 provides management of the HDCP setting:

SW4 HDCP Mode
0 HDCP Bypass – Output HDCP same as input HDCP
1 Cascade Mode – Used when there are several devices in a chain. (Off)

Output Scaling

When a 4K HDMI signal is provided at the input, but the display can only display 1080p, that output will be automatically downscaled to 1080p to ensure that an image will be displayed. The following table gives the input signal requirements to ensure that the scaling will be successful. Since the scaling is per output, any display that does support the 4K HDMI input signal will always display at the same 4K resolution supplied at the HDMI input connector of the SY-HS14E-18G.

Input Resolution Can Downscale Output Resolution
3840×2160 60Hz 4:4:4 Yes 1080p 60Hz 4:4:4
3840×2160 30Hz 4:4:4 Yes 1080p 30Hz 4:4:4
3840×2160 24Hz 4:4:4 Yes 1080p 24Hz 4:4:4
3840×2160 60Hz 4:2:0 Yes 1080p 60Hz 4:4:4
3840×2160 30Hz 4:2:0 Yes 1080p 30Hz 4:4:4
3840×2160 24Hz 4:2:0 Yes 1080p 24Hz 4:4:4
3840×2160 60Hz 4:2:2 Not Supported N/A
3840×2160 30Hz 4:2:2 Not Supported N/A
3840×2160 24Hz 4:2:2 Not Supported N/A

Powering Active HDMI Cables
Each HDMI output is capable of powering active HDMI cables, including Active Optical Cables (AOC).
Up to 500mA of current can be supplied by the 5V pin (pin 18) per output port. This ensures stable and reliable use of Active HDMI cables without any need for external PSU. Care should be taken to ensure that the total current for all outputs as a whole does not exceed 1A.

Troubleshooting

Use of high quality High-Speed HDMI cables are recommended. Maximum HDMI cable length depends on cable quality, the source and the sink capabilities.
The following table lists some of the basic checks that should be performed if no video is displayed:

Problem Possible cause Solutions to try first
Power LED off PSU problem ·  Check that PSU output voltage is correct,

and the current rating is sufficient to power the system.
·  Check that connection polarity is correct, this product uses a centre positive connection.
IN LED off| No HDMI Input| ·  Check that the HDMI source is outputting an image.
·  Check that the HDMI cables are properly connected.
Output LED off| No HDMI output| ·  Check that the HDMI display is on.
·  Check that correct input is selected on the HDMI sink device (display).
·  Check that the HDMI cables are properly connected.
·  Any unused outputs will always be indicated by its LED being in the OFF state.

Packing List

  • 1x SY-HS14E-18G (1×4 Splitter)
  • 2x Side brackets
  • 1x PSU (12V 1A)
  • 4x Rubber pads
  • 1x User Manual

Specifications

General

HDMI Video Support| VESA and SMPTE 480p to 2160p with 3D and HDR.
All HDMI resolutions to 3840×2160 @60Hz 4:4:4 (Max. of 18 Gbps) All PC resolutions to 1920×1200 @60Hz
---|---
HDMI Version| 2.0 – All HDMI versions to 2.0
HDCP Version| 1.4, 2.2 and 2.3
CEC| Supported
Audio format| LPCM 2ch or 7.1ch, Dolby Digital 2 or 5.1ch, DTS 2 or 5.1ch
Input Connectors| 1x HDMI Type A
1x 2.1mm barrel connector 1x Micro USB
Output Connectors| 4x HDMI Type A
Power Supply| 12V DC @ 1A max.
Power Consumption| 2.5W max. (SY-HS14E-18G only)
Switches| 4-way DIP switch for EDID and HDCP control
Max. HDMI Cable Length
(High quality High-Speed HDMI cable)| 4K60 4:4:4 ≤ 5m
4K60 4:2:0 ≤ 12m
1080p ≤ 18m

Environmental

Operating Temperature -10 to +55°C (+14 to +131°F)
Operating Humidity 10 to 90 % RH (non-condensing)

Physical

Dimensions (WxHxD) 142 x 17.5 x 70.5 mm
Case Material Steel chassis
Weight 260g

Part Number

SY-HS14E-18G 1×4 HDMI 2.0 Splitter with 4K à 1080p Scaling

Safety Instructions

To ensure reliable operation of this product as well as protecting the safety of any person using or handling this device while powered, please observe the following instructions.

  1. Use the power supply provided. If an alternate supply is required, check the voltage, polarity and that it has sufficient power to supply the device it is connected to.
  2.  Do not operate this product outside the specified temperature and humidity range given in the above specifications.
  3.  Ensure there is adequate ventilation to allow this product to operate efficiently.
  4. Repair of this equipment should only be carried out by qualified professionals as this product contains sensitive devices that may be damaged by any mistreatment.
  5.  Only use this product in a dry environment. Do not allow any liquids or harmful chemicals to come into contact with this product.

After Sales Service

  1. Should you experience any problems while using this product, firstly refer to the Troubleshooting section in this manual before contacting SY Technical Support.

  2. When calling SY Technical Support, the following information should be provided:
    • Product name and model number
    • Product serial number
    • Details of the fault and any conditions under which the fault occurs.

  3. This product has a two year standard warranty, beginning from the date of purchase as stated on the sales invoice. For full details please refer to our Terms and Conditions.

  4.  SY Product warranty is automatically void under any of the following conditions:
    • The product is already outside of its warranty period
    • Damage to the product due to incorrect usage or storage
    • Damage caused by unauthorised repairs
    • Damage caused by mistreatment of the product

  5.  Please direct any questions or problems you may have to your local dealer before contacting SY Electronics.

  6. V1.0

sy.uk
V1.0

References

Read User Manual Online (PDF format)

Read User Manual Online (PDF format)  >>

Download This Manual (PDF format)

Download this manual  >>

Related Manuals