YEELIGHT YLLDDXN01 Natural Light Floor Lamp User Manual

YEELIGHT YLLDDXN01 Natural Light Floor Lamp

Product Information

Specifications

• Model: H1BOUPOFDPPMHSBZ
• Dimensions: 30 x 4 inches
• Weight: 2 lbs
• Material: High-quality plastic

Product Usage Instructions

Assembly

1. Lay out all parts and ensure you have all components listed in the manual.
2. Follow the step-by-step instructions provided to assemble the product.

Operation

1. Turn on the product by pressing the power button located on the front panel.
2. Use the control knob to adjust settings according to your reference.

Maintenance

1. Clean the product regularly with a damp cloth to remove dust and dirt.
2. Avoid using harsh chemicals that may damage the product’s surface.

Frequently Asked Questions (FAQ)

• Q: How do I change the batteries?
  A: To change the batteries, locate the battery compartment on the back of the product and replace with new batteries following the polarity markings.

• Q: Can this product be used outdoors?
  A: This product is designed for indoor use only and should not be exposed to outdoor elements.

Customer service small. support cellent.com Made in China

Yeelight Natural Light Floor Lamp User Manual
Product Introduction Before using this product, please read this manual carefully and keep it for future reference

NOTES

1. Three types of screws with numbers 1. 2, and 3 are grinded with corresponding numbers on their necklacing bag.
2. Each type of screws model includes a spare screw
3. There are two screw holes on the back de the upper are lower lamp poles, please do not install thermic upside down.

NOTES
The illustrations of products, accessories and user interlace in the manual are schematic reference only. Due to product updates and upgrades, there may be slight differences between the actual product are the schematic diagram Please fate to the actual product for accouters

How to Install

1. Take 4 screws from accessory bag No. 1, lock the lamp head crossbar to the upper lamp pole, and then connect the wire terminals inside the crossbar and upper lamp pole (there are two screw holes at the bottom rear of the upper lamp pole, please pay attention to the front and rear orientation of the lamp pole during installation).

2. Take out the lamp head crossbar cover from the accessory bag and lock it with the 2 screws in accessory bag No.2.
   Installation Tips

   • The lining at the packaging box can be used as an biliary future for easy assembly of the base and lower lamp pole. Gesture installation, Please take out all the lining from the box.
     

3.  Place the long edge of the base into the wide groove of the inner liner, and move the accessory liner to the top of the inner box liner to serve as a pad for installing the lower lamp pole. Insert the lower lamp pole into the groove or the pao, allen the & screw holes at the bottom with the screw holes on the base, and use « screws. from accessory bag No.1 to lock the lower lamp pole to the base from the back of the base (there is a power socket at the bottom rear of the lower arm pole, please pay attention to the orientation during installation).

4. After the above assembly, connect the wire terminals inside the upper and lower lamp poles, and use 2 screws from accessory bag No.3 to lock the connection between the two lamp poles
   

5.  Insert the power plug into the power socket at the rear bottom of the lower lamp pole, place the lamp in its actual usage position, and it needed, you can rotate the lamp head 90 to better lit the direction of the desk.

   • Notes
   • Please use the subsoiled accessories lore installation and do not replace them  to avoid damaging. the lamp or improper assembly
   • Do not connect the lower actors installation is completed to prevent electing shock.
   • Strolls lolled the Steps in the instruction manual tor installation. Improper installation may cause product taller

Remote Control

1. Open the magnetic cover from the bottom of the remote controller.
2.  Remove the insulation pads from the two button batteries, and close the cover.

Notes.

• The button cell battery type is CRA032, the voltage is 3V
• Wien replacing the batteries, please ensure that the “+” sale of the 2 batteries faces outward as shown. in the diagram.

Remarks

• Remove and immediately recycle or dispose of used battiness according to the local regulations and keep away from children. Do NOT dispose of batteries in household waste or incinerate.

• Even used batteries may cause severe injury or death.

• Call a local poison control center for treatment information

• Non-rechargeable batteries are not to be recharged.

• Do not force discharge, recharge, disassemble, heat above (manufacturer’s specitied temperature rating, or incinerate. Doing so may result in injury due to venting, leakage or explosion resulting in chemical bums.
  Ensure the batteries are installed correctly according to polarity (+ and -)

• Do not mix old and new batteries, different brands or types of battens, such as alkaline, carbon-zine, or rechargeable batteries.

• Remove and immediately recycle or dispose of batteries from equipment note used for an extended period of time according to local regulations

• Always completely secure the battery compartment. It the battery compartment does not close securely, stop using the product, remove the batteries, and keen them away from children.

How to Use

• The lamp is controlled by a wireless Bluetooth remote control, short press to switch on and off, rotate to adjust the brightness, and double click to enable the focus mode.

• Lamp pairing Method
  To power on the lamp (Calore powering on, it is necessary to ensure that the power time has exceeded 2 seconds), and long press the remote control within 1 minute. When the light casts a centile pulsation, it indicates a successful paring

• Notes:   When it leaves the factory, the remote control is paired with the lamp and can be used directly.

• It the remote control is lost or malfunctioning, and the lamp moods to be matched with a new remote control, please use the above method to complete the pairing

Focus model
After tuming on the focus mode, the light emits three pulses to remind you that the focus time has been activated. Alter 45 minutes, the light emits pulses pain to remind you that the 10-minute break timer has been turned on. The focus mode loops twice by default and automatically turns of alter t loop end.

Product Specifications

Product features

Notes

• Clean the product surface with a soft cotton cloth. Do not use corrosive solutions.
• Dispose of used batteries properly to prevent environmental pollution.
• The light source is not replaceable. Replace the entire lamp when its like enols.
• This product is for indoor use only.
• Ensure the lamp is placed stably and not inclined.
• Do not connect to never detour installation is completed to avoid electric shock.
• It the power cord is damaged, it must be replaced by the manufacturer or a professional to avoid Nazaro.

FCC Compliance Statement

This device complies with part 15 of the FCC Rules. Operation is subject to the following two conditions:

1. This device may not cause harmful interference, and
2. This device must accept any interference received, including interference that may cause undesired operation.

Caution: Changes or modifications to this unit not expressly approved by the party responsible for compliance could void the user’s authority to operate the equipment. This device contains licence-exempt transmitter(s)/receiver(s) that comply with Innovation, Science and Economic Development Canada s licence-exempt RSS(s).
Operation is subject to the following two conditions:

1. This device may not cause interference.
2. This device must accept any interference, including interference that may cause undesired operation of the device.

NOTE: This equipment has been tested and found to comply with the limits for a Class 8 digital device, pursuant to part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation. This equipment generates, uses and can radiate radio frequency energy and. if not installed and used in accordance with the instructions, may cause harmful interference to radio communications. However, there is no guarantee that interference will not occur in a particular installation.

• If this equipment does cause harmful interference to radio or television reception, which can be determined by turning the equipment off and on, the user is encouraged to try to correct the interference by one or more of the following measures:
• Reorient or relocate the receiving antenna.
• Increase the separation between the equipment and receiver.
• Connect the equipment into an outlet on a circuit different from that to which the receiver is connected.
• consult the dealer or an experienced radio/TV technician for help.

To satiety FuC & C Rr exposure requirements, a separation distance of 20 cm or more should be maintained between the antenna of this device and persons during device actuation. o ensure compliance, operation’s  closer than this distance is not recommended. Limited by local law regulations, version for North America does not have region selection option.

Supplier’s Declaration of Conformity

Under FCC Part 15 SDoC procedure

• Product Description: Yeelight Natural Light Floor Lamp, Yeelight Natural Light Floor Lamp Controller
• Model Number: YLLDD-0022, YLLDDXN01
• Trade Name: YEELIGHT
• Responsible Party in USA: Yeelight Technology LLC
• Testing Laboratory: Shenzhen UnionTrust Quality and Technology Co., Ltd.
• Addendum to the Test Report: 240413785HA-001, 2404B1379SHA-001

This device complies with part 15 of the FCC Rules.
Operation is subject to the following two conditions:

1. This device may not cause harmful interference, and
2. This device must accept any interference received, including interference that may cause undesired operation.

For and on behalf of the Responsible Party

Read User Manual Online (PDF format)

Read User Manual Online (PDF format)  >>

Download This Manual (PDF format)

Download this manual  >>