Netum C830 C Series Barcode Scanner User Manual

Netum C830 C Series Barcode Scanner User Manual

Package Included

• 1PC X Scanner
• 1PC X 2.4G USB Receiver
• 1PC X USB Cable
• 1PC X Quick Setup Guide

Product Information

Firmware Version
The firmware version will be displayed by scanning “$SW#VER”.

Barcode Programming

Netum barcode scanners are factory-programmed for the most common terminal and communications settings. If you need to change these settings, programming is accomplished by scanning the bar codes in this guide. An asterisk (*) next to an option indicates the default setting.

Notes

• Many command barcodes only work with scanners in a particular connection mode.
• Please pay attention to the below symbol when you scan the command barcodes.
• Command barcodes only apply to scanner work via Bluetooth connection.
• Command barcodes only apply to scanner work via Wireless Connection.
• Command barcodes only apply to scanner work via USB Wired Connection

Connection Way
The scanner can be connected to your device via Bluetooth, USB receiver or USB cable, you can choose one of the connection ways to connect the scanner to your device.

Working Via USB Cable
Get Started: Connect the scanner to your device via a USB cable. If you use a US keyboard, it’s plug-and-play. If you use another type of keyboard, please refer to “keyboard language” to configure the keyboard language before you use it.

Working Via USB Dongle (Wireless Mode)
Get Started: Plug the USB dongle on your computer. If you use a US keyboard, it’s plug-and-play. If you use another type of keyboard, please refer to “keyboard language” to configure the keyboard language before using it.

Working Via Bluetooth
Get Started: Scan “Working via Bluetooth”, pairing the Bluetooth. The US Keyboard is set by default, if you use other types of keyboards, please configure the keyboard language before you use it.

Notes

• Pressing the scan button will initiate the attempts to connect.
• If a connection is made, the blue light will stop blinking and turn solid.
• If a connection is not made after several attempts, the scanner will emit a long beep (and the blue light will turn off).
• The Bluetooth working channel is not set by default. If you want to work via Bluetooth, you have to scan the command barcode “Working via Bluetooth” before pairing.
• If you want to shift from a Bluetooth working channel to an RF
• Wireless channel, you have to scan ” RF Wireless Transmit” and then plug the USB receiver into your device.

Basic Mode (HID) (default)

NO software installation needed

Connects to most devices
The scanner interacts with a host device like a keyboard

Application Mode (Apple Specific Serial Profile)

For iOS Devices
If you have an iOS application that supports our Scanners this is the mode to use

Application Mode (Serial Port Profile)
For Android or Windows

Software installation is required
If you have an application that supports this is the mode recommended

Notes
If you want to shift from HID to SPP or BLE just scan the corresponding command barcode. If you want to shift from SPP or BLE to HID mode, first ignore (or delete) “Netum Bluetooth” → turn off Bluetooth → scan the command barcode of HID → Open the Bluetooth → re-pair it.

Transmission Speed Via Bluetooth Connection
Scanning the appropriate barcode below will change the Bluetooth transmit speed.

USB DONGLE AS HID-KBW
When you plug the USB dongle into your device, the USB HID-KBW feature will be enabled by default. Then scanner’s transmission will be simulated as USB keyboard input. It works on a Plug and Play basis and no driver is required.

USB DONGLE AS VIRTUAL COM

USB COM Port Emulation
If you connect the scanner to the Host via a USB dongle, scanning the “USB COM Port Emulation” will allow your device to receive data in the way a serial port does.

USB HID-KBW
When the scanner is connected to your device via a USB cable, the USB HID-KBW feature will be enabled by default. Then scanner’s transmission will be simulated as USB keyboard input. It works on a Plug and Play basis and no driver is required.

USB COM Port Emulation
If you connect the scanner to your device via a USB cable, scanning the “USB COM Port Emulation” will allow your device to receive data in the way a serial port does.

Keyboard Language
For example, If you use a French Keyboard, scan the command barcode of “French keyboard “. If you use a US keyboard you can ignore this step.

Working Mode
If you are heading for a working area that lies outside the Bluetooth signal range, you may activate the scanner’s store mode, by following the steps described below. Under this mode, all scanned data will be stored directly in the buffer memory of the device. Furthermore, data entries will be permanently saved in the buffer memory before the manual upload into the working station, so that you may upload them when you are near your working device.

Idle Time
The period set for the scanner from idle to sleep.

Convert Case

Beep Volume
Scanning the appropriate barcode below will change the beep volume.

Function Key Mapping
When Function Key Mapping is enabled, function characters are sent over the keypad.

LED Activity/Beep Pattern/Indication under different Connections

2.4G RF Wireless Connection

Bluetooth LED Activity| Beep Pattern| Read indicator LED Activity (Square Shape)| Indication| Working Mode
---|---|---|---|---
OFF| No beep| OFF| Sleeping

/Power OFF

|
Blue LED ON and then OFF| Beep Once| Blue LED ON and then OFF| Wake up from Sleep Mode|
White LED ON and then OFF| Beep Once| Blue LED ON and then OFF| successful scan| Normal Mode
OFF| Beep Once| Blue LED ON and then OFF| Go to sleep|
OFF| 3

Beeps

| Red LED Flash Three Times and Then OFF| Data transmit failed|
White LED ON and then OFF| Beep Once| Blue LED ON and then OFF, Green LED Flashing| successful scan| Store Mode

Bluetooth Connection

Bluetooth LED Activity| Beep Pattern| Read indicator LED Activity (Square Shape)| Indication| Working Mode
---|---|---|---|---
OFF| No beep| OFF| Sleeping

/Power OFF

|
Blue LED ON and then OFF| Beep Once| Blue LED ON and then OFF| Go to sleep Mode|
Blue LED ON| Beep Once| Blue LED ON and then OFF| successful scan| Normal Mode
Blue LED Flashing| Beep Once| OFF| Bluetooth Pairing|
Solid Blue LED (No Flashing)| Beep Once| Blue LED ON and then OFF| Bluetooth Paired|
Blue LED Flashing| 3 Beeps| Red LED Flashing 3 times and then Off| Data transmit failed|
Blue LED ON and then OFF| Beep Once| Blue LED ON and then OFF, Green LED Flashing| successful scan| Store Mode

Charge Power

Bluetooth LED Activity| Beep Pattern| Read indicator LED Activity (Square Shape)| Indication| Working Mode
---|---|---|---|---
OFF| 5 beeps| RED LED flashing 5 times| Low Power Warning|
OFF| No beep| RED LED ON| Charging Power|
OFF| No beep| Green LED ON| Full Charge|

FAQs

Some barcodes cannot be read, why?

• Dirty or unclear barcodes might not be read.
• The possible reason is that the setting for some barcode types not commonly used is off by default. You need to activate a specific barcode type to get it to work.
• Please contact us for help or you may go to our official website “www.netum.com“; to download the complete manual and then refer to the section “Symbologies”.

How to change the terminator to TAB?
Please refer to the section “Terminator configuration” from the manual on our official website.

Are there any barcodes for applying or removing prefixes & suffixes?
Yes, you may go to our official website “www.netum.com”; to download the manual, refer to the section “prefix and suffix” or turn to customer service for help.

How to solve the messy code problem encountered while using other foreign languages?
The default language is English. Please refer to “Keyboard Language” to change the language.

Why scanner can not read the Italy Pharmacy code?
Download the manual from our official website according to the scanner’s model number, refer to the section of Code32 then scan “Enable Code32” to enable the scanner to read Italy pharmacy code.

Why scanner can not read add-on 2 or 5 codes?
Download the manual from our official website according to the scanner’s model number, refer to the section of ADD-On code and scan the appropriate command barcode to enable the scanner to read it.

Why scanner can not read DataMatrix GS1 in the correct format?
Scan “Enable Function Key Mapping” from this manual will enable the scanner to output the group separator.

Note
Please do not hesitate to contact us if you need any other configurations.

Contact Information
Tel.: +0086 20-3222-8813
WhatsApp: +86 136 222 33 974
Email: service@netum.net
Address: Room 301, 6th Floor and full 3rd Floor, Building 1, No. 51 Xiangshan Avenue
Ningxia Street, Zengcheng District, Guangzhou City, Guangdong Province China/511356
Website: https://www.netum.net/
EU Name: Apex CE Specialists GmbH
Add: Habichtweg 1 41468 Neuss Germany
UK Name: APEX CE SPECIALISTS LIMITED
Add: 89 Princess Street, Manchester, M1 4HT, UK

Download PDF:Netum C830 C Series Barcode Scanner User Manual

Read User Manual Online (PDF format)

Read User Manual Online (PDF format)  >>

Download This Manual (PDF format)

Download this manual  >>