offgridtec 30m Protective Grid Instruction Manual

June 22, 2024
Offgridtec

offgridtec 30m Protective Grid

Specifications :

  • Product Name: Offgridtec Protective Grid 30m
  • Contents:
    • 1 roll solar panel mesh (30 meters)
    • 100 units of J-hook (Stainless steel)
    • 100 units of Speed Washer (Stainless steel)

Product Usage Instructions

Solar Panel Mesh Straight Side Installation:

  1. Measure the length of the solar panel with a tape measure.
  2. Cut the solar panel mesh according to the panel length with a wire cutter.
  3. Compare the height of the solar panel and the solar panel mesh.
  4. Fold the extra height of the solar panel mesh at a 45-degree angle with a square wooden rod.
  5. Put the hook side of J-hook through the mesh, and hook it to the panel frame.
  6. Sleeve the speed washer through the rod of J-Hook, then tighten it against the mesh.
  7. Bend the J-hook rod upwards with hands.
  8. Cut off the excess portion of the J-hook rod with pliers.
  9. Add J-hook and secure speed washer to fix overlapping meshes according to steps 5-8.

Solar Panel Mesh External Corner Installation:

  1. Measure to determine where the bend will go with a tape measure.
  2. Cut the mesh a straight slit near the rooftop in the corner part with a wire cutter.
  3. Bend the mesh along the slit at a 90-degree angle and place it around the corner.
  4. Fasten the outside corner mesh and solar panel with J-hooks and speed washers.
  5. Tie the small solar panel mesh and corner solar panel mesh in place with corner zip ties.
  6. Cut off the excess portion of the zip ties on solar panel meshes with a wire cutter.

Solar Panel Mesh Internal Corner Installation:

  1. Match the mesh and solar panel corner to determine the position of the internal corner of the mesh.
  2. Cut a 45-degree slit at the solar panel mesh bottom with pliers.
  3. Bend two ends of the mesh in opposite directions to overlap the cut ends.
  4. Secure both ends of the inside corner solar panel mesh with J-hooks and speed washers.
  5. Lock the bottom slit with zip ties. And cut off the excess portion with a wire cutter.

FAQ :

  • Q: Can I reuse the J-hooks and speed washers?
    A: It is recommended to use new J-hooks and speed washers for each installation to ensure proper functionality and safety.

Offgridtec Protective Grid 30m

Contents

  • 1 roll solar panel mesh (30mts)
  • 100 units of J-hook (Stainless steel)
  • 100 units of Speed Washer (Stainless steel)

How to install (when side installation)

  • Measure the length of solar panel with a tape measure.
  • Cut the solar panel mesh according to the panel length with a wire cutter.
  • Compare the height of the solar panel and the solar panel mesh.
  • Fold the extra height of solar panel mesh at 45 degree with a square wooden rod.
  • Put the hook side of J-hook through the mesh, and hook it to the panel frame
  • Sleeve the speed washer through the rod of J-Hook, then tighten it against the mesh.
  • Bend the J-hook rod upwards with hands.
  • Cut off the excess portion of the J-hook rod with pliers.
  • Attach J-hooks approximately every 12″ – 18″ (30 cm – 50 cm).
  • Overlap about 2″ – 4″ (50 mm – 100 mm) when start a new piece of mesh. Add J-hook and secure speed washer to fix overlapping meshes according to step 5-8.
  • Add J-hook and secure speed washer to fix overlapping meshes according to step 5-8.
  • Solar panel meshes straight side installation is finished on rooftop.

How to install (when external corner installation)

  • Measure to determine where the bend will go with a tape measure.
  • Cut the mesh a straight slit near the rooftop in the corner part with a wire cutter.
  • Bend the mesh along the slit at a 90 degree angle and place it around the corner.
  • Bend the mesh along the slit at a 90 degree angle and place it around the corner.
  • Cut a small mesh about 2″ × 4″ to cover the gap between the corner mesh and the rooftop.
  • Tie the small solar panel mesh and corner solar panel mesh in place with corner zip ties.
  • Cut off the excess portion of the zip ties on solar panel meshes with wire cutter.
  • Solar panel mesh external corner installation is finished.

How to install (when internal corner installation)

  • Match the mesh and solar panel corner to determine the position of the internal corner of the mesh.
  • Cut a 45 degree slit at the solar panel mesh bottom with pliers.
  • Bend 2 ends of mesh in opposite directions to overlap the cut ends.
  • Secure both ends of the inside corner solar panel mesh with J-hooks and speed washers.
  • Lock the bottom slit with zip ties. And cut off the excess portion with wire cutter.
  • Solar panel mesh internal corner installation is finished.

Read User Manual Online (PDF format)

Read User Manual Online (PDF format)  >>

Download This Manual (PDF format)

Download this manual  >>

Related Manuals