Levoit LV600S Smart Hybrid Ultrasonic Humidifier: User Manual & Specs

The Levoit LV600S Smart Hybrid Ultrasonic Humidifier is a high-quality device designed to improve the air quality in your home or office. This user manual provides detailed instructions on how to use and maintain the humidifier, as well as important safety information to ensure that you can operate it safely. The package includes the humidifier, three aroma pads, three absorption pads, two water filter sponges, a cleaning brush, a user manual, and a quick start guide. The humidifier has a 6-liter water tank capacity and can run for up to 50 hours on low mist setting. It also has a maximum cool mist output of 300 ml/h and a maximum warm mist output of 550 mL/h. The device is equipped with Wi-Fi and Bluetooth capabilities, allowing you to control it remotely using the VeSync app. This manual also includes a function diagram, indicators, and controls to help you navigate the device with ease. Before using the humidifier, it is important to read and understand all safety guidelines to avoid any potential hazards.

levoit LV600S-EU Smart Hybrid Ultrasonic Humidifier

Package Contents

• 1* Smart Hybrid Ultrasonic Humidifier
• 3 * Aroma Pad (1 Pre-Installed)
• 3 * Absorption Pad (1 Pre-Installed)
• 2x Water Filter Sponge (1 Pre-Installed)
• 1 * Cleaning Brush
• 1* User Manual
• 1* Quick Start Guide

Specifications

Note: The humidifier may run for a longer or shorter time depending on the environmental temperature and humidity

Noise Level| Lowest: < 28dB (Low Cool Mist)

Highest: < 40dB (High Warm Mist)

Effective Range| 40-70 m2 / 430-753 ft2
Dimensions| 29.4 x 19.5 x 28.8 cm / 11.6 x 7.7 x 11.3 in
Weight| 2.7 kg/ 6 lb
Wi-Fi ® Frequency Range| 2412-2472MHz
E.I.R.P.: 19.0 dBm
Bluetooth ® Frequency Range| 2402-2480MHz
E.I.R.P.: 10.0 dBm

READ AND SAVE THESE INSTRUCTIONS

SAFETY INFORMATION

To reduce the risk of fire, electric shock, or other injury, follow all instructions and safety guidelines.

General Safety

• Only use the humidifier as described in this manual.
• Place the humidifier and cord so that it will not be knocked over. Do not place near large pieces of furniture or in high-traffic areas.
• When not in use, turn the humidifier off and disconnect from power by removing the plug from the outlet.
• Do not use the humidifier in wet environments.
• Keep the humidifier out of reach from children.
• Do not open the base or remove the water level sensor for self-servicing.
• Always unplug your humidifier from the power outlet before cleaning your humidifier or detaching the water tank from the humidifier base.
• Always make sure to place the humidifier on a flat, level surface before operation.
• Only fill the water tank with clean water. Never fill the water tank with any other liquids.
• Do not place the humidifier near sources of heat, such as stovetops, ovens, or radiators.
• Do not place the humidifier directly on floors, carpets, or rugs.
• Do not use other items as replacement parts for this product.
• Do not cover the nozzles while the humidifier is on. Doing so may damage the humidifier.
• Remove the water tank from the base before moving the humidifier.
• Do not immerse the humidifier base, power cord, or plug in water.
• Do not clean the humidifier immediately after turning it off, especially if it has been diffusing warm mist. Allow the humidifier to cool down completely before cleaning.
• If the humidifier is damaged or is not functioning properly, stop using it and contact Customer Support immediately (see page 27).
• This humidifier can be used by children 8 years and older as well as persons with reduced physical, sensory, or mental capabilities or lack of experience and knowledge if they have been given supervision or instruction concerning use of the humidifier in a safe way and understand the hazards involved.
• Supervise children when they are near the humidifier.
• Children should not clean or perform maintenance on the humidifier without supervision.
• Not for commercial use. Household use only.

Caution: Risk of Leaks and Electric Shock
Do not add essential oils, supplemental water treatment liquids, or water filters into the water tank or base chamber. This will damage the humidifier and cause leaks. Only add essential oils to the aroma pad.

Power & Cord 

• Do not handle the power cord or plug with wet hands. Keep the plug and power cord away from liquids.
• If the power supply cord is damaged, it must be replaced by Arovast Corporation or similarly qualified persons in order to avoid an electric or fire hazard. Please contact Customer Support (see page 27).
• Unplugging the power cord will disable remote control of the humidifier and temporarily disconnect the humidifier from VeSync and other third-party apps.

Electromagnetic Fields (EMF)
This humidifier complies with all standards regarding electromagnetic fields (EMF). If handled properly and according to the instructions in this user manual, the appliance is safe to use based on scientific evidence available today.

Maintenance Safety
This symbol means the product must not be discarded as household waste, and should be delivered to an appropriate collection facility for recycling. Proper disposal and recycling helps protect natural resources, human health and the environment. For more information on disposal and recycling of this product, contact your local municipality, disposal service, or the shop where you bought this product.

CLEAN THE WATER TANK AND BASE CHAMBER EVERY 3 DAYS OR LESS.

• Be aware that high humidity levels may encourage the growth of biological organisms in the environment.
• Do not permit the area around the humidifier to become damp or wet. If dampness occurs, turn the output of the humidifier down. If the humidifier output volume cannot be turned down, use the humidifier intermittently. Do not allow absorbent materials, such as carpeting, curtains, drapes, or tablecloths, to become damp.
• Unplug the humidifier during filling and cleaning.
• Never leave water in the reservoir when the humidifier is not in use.
• Empty and clean the humidifier before storage. Clean the humidifier before next use.
• Warning : Micro-organisms that may be present in the water or in the environment where the humidifier is used or stored, can grow in the water reservoir and be blown in the air causing very serious health risks when the water is not renewed and when the tank is not cleaned properly every 3 days.
• Empty the tank and refill every third day. Before refilling, clean it with fresh tap water or cleaning agents (see Cleaning, page 17). Remove any scale, deposits, or film that have formed on the sides of the tank or on interior surfaces, and wipe all surfaces dry. See Cleaning (page 17) for in-depth instructions.

GETTING TO KNOW YOUR SMART HUMIDIFIER

Function Diagram

1. A. Nozzles
2. B. Top Cover
3. C. Handle
4. D. Water Tank
5. E. Water Filter
6. F. Water Filter Sponge
7. G. Base
8. H. LED Display
9. I. Control Panel
10. J. Aroma Box
11. K. Aroma Pad
12. L. Humidity Sensor (In Aroma Box Compartment)
13. M. Mist Tube
14. N. Mist Channel
15. O. Noise Silencer
16. P Absorption Pad
17. Q. Air Outlet
18. R. Float Brackets
19. S. Inner Chamber
20. T. Power Cord
21. U. Water Outlet Valve
22. V. Heating Element
23. W. Transducer
24. X. Float

Indicators

1. A. Sleep Mode Indicator

2. B. Timer Indicator

3. C. Wi-Fi Indicator

4. D. No Water Indicator

5. E. Relative Humidity (RH) Percentage

6. F. Warm Mist Setting Indicator

7. G. Mist Level Indicator
   Buttons

8. H. On/Off Button

9. I. Mist Level Button

10. J.  Humidity Level Button

11. K. Timer Button

12. L. Warm Mist Button

13. M. Sleep Mode Button

Mist Level Indicator (Blue)

• Low Mist
• Medium Mist
• High Mist

Warm Mist Indicator (Orange)

• Heat Off (Cool Mist)
• Low Heat
• Medium Heat
• High Heat

CONTROLS

Note : You can also use the VeSync opp to control these functions, as well as additional opp-only features (see page 16).

On/Off Button

• Press to turn the humidifier on/off.
• Press and hold for 5 seconds to pair with the VeSync app. See the VeSync in-app instructions for more information.
• Press and hold for 15 seconds to reset the humidifier. This will restore the humidifier’s default settings and disconnect it from Wi-Fi® and the VeSync app (see page 1).

Mist Level Button

• Press repeatedly to cycle through mist level settings low, medium, and high mist.
• Press and hold for 3 seconds to turn the display off. Press any button to turn the display back on.

Humidity Level Button

• Sets the relative humidity (RH) percentage. The humidifier will automatically stop misting when the room reaches the target humidity level (see page 13).
• Press and hold for 2 seconds to cancel your humidity level setting.

Timer Button
Sets or cancels timer (see page 14).

Warm Mist Button
Cycles through warm mist settings: low heat, medium heat, high heat, and heat off (see page 13).

Sleep Mode Button
Press to turn Sleep Mode on/off (see page 14).

Wi-Fi Indicator
Turns on, off, or blinks to indicate pairing status. See the VeSync in-app instructions for more information.

No Water Indicator

• Blinks when there is no water in the tank. After this indicator blinks 10 times, the humidifier will turn off. Refill the tank and properly place it on the base to use your humidifier.
• Lights up when the water tank is removed. Remains on until the tank is replaced.

GETTING STARTED

1. Remove all packaging.

2. Clean the water tank and water tank cover before first use
   Note : Check to make sure that the water filter is correctly in place. If not, then rotate the filter clockwise to secure itin place.

3. Choose a hard, flat location for the humidifier at least 30 cm/ 12 inches away from any walls. The surface must be water-resistant. [Figure 1.1] , Do not place the humidifier directly on floors, carpets, or rugs.

4. Mist should be directed away fr om walls, furniture, bedding, and appliances. Avoid letting too much mist fall on the side of the humidifier with the aroma box, as this may interfere with the sensor inside the aroma box.
   Note : The humidity sensor and an air inlet are both located inside the aroma box. Placing the humidifier away from walls will also ensure that the inlet and sensor function properly

FILLING & REFILLING

Note : Make sure the water tank is clean before filling.

1. Remove the water tank cover.

2. Use the handle to remove the tank from the base. Fill the tank with roomtemperature water. Do not fill with hot water.
   Note:

3. We recommend using purified water to fill the tank.

4. Using tap water may result in a white dust (dried minerals) on surfaces.

5. Replace the water tank cover and place the tank back on the base.

Caution

• Do not add water directly into the base chamber.
• Do not add water through the mist tube.
• Do not add essential oils into the humidifier. Only add essential oils to the aroma pad
• Do not use water treatment liquids or third-party water filters in this humidifier.

VESYNC APP SETUP

Note : Due to ongoing updates and improvements, the VeSync opp may be slightly different than shown in the manual. In case of any differences, follow the in-opp instructions.

1. To download the VeSync app, scan the OR code or search “VeSync” in the Apple App Store® or Google Play Store.
   Note : For Android™ users, choose “Allow” to use VeSync.

2. Open the VeSync app. If you already have an account, tap Log In. To create a new account, tap Sign Up.
   Note : You must create your own VeSync account to use third-party services and products. These will not work with a guest account. With a VeSync account, you can also allow your family and friends to control your smart humidifier.

3. Follow the in-app instructions to set up your smart humidifier.
   Note:

4. You can use the VeSync opp to connect your smart humidifier to Amazon Alexa or Google Assistant”‘. Follow the in-opp instructions to connect VeSync to your voice assistant.

5. Your phone must have Location turned on while your phone is connecting ta your smart humidifier. This is required to establish the Bluetooth® connection. You can turn Location off after your smart humidifier is finished connecting to the VeSync opp.

Wi-Fi Connection

1. To disconnect Wi-Fi, press and hold (9 for 15 seconds until the Wi-Fi indicator turns off. T his will restore the smart humidifier’s default settings and disconnect it from the VeSync app.
2. To reconnect, please follow the instructions in the VeSync app for adding a device

USING YOUR SMART HUMIDIFIER

Note : Using the VeSync opp allows you to control your smart humidifier remotely and access additional functions and features (see page 16).

1. Plug in the humidifier. The humidifier will light up, then turn off.

2. Press to turn your humidifier on. The humidifier will start misting.
   Note : If there is no water in the tank, will flash 10 times, and the humidifier will turn off. Fill the water tank (see Getting Started, page 9).

3. Press repeatedly to cycle through mist settings: Low, Medium, and High.

4. Rotate the nozzles to adjust the direction of the mist. [Figure 3.1] Note : Direct the nozzles away from any furniture, walls, or other objects to prevent them from getting wet. Do not inhale the mist directly from the nozzles.

5. Optionally, use the controls or the VeSync app to turn on warm mist, activate Sleep Mode, and more (see Controls, page 8).

6. When your room has reached your preferred humidity level, turn the humidifier to a lower setting, or turn it off. A comfortable humidity level is between 40% and 60%.
   Note : You can also set the humidifier to automatically stop misting when the room reaches a specific humidity level (see Humidity Level, page 13).

7. Press to turn your humidifier off.

Warm Mist

• Press to turn on warm mist. Keep pressing to increase the heat setting for the mist, and to turn warm mist off.
• Caution: Mist may be hot. Do not place your bare hands, face, or other exposed skin over the nozzles while using warm mist. [Figure 3.2]
• The humidifier may take 15 minutes to warm up before producing warm mist.
• The warm mist function can be used during Sleep Mode.

Humidity Level
You can customise the humidity level that the humidifier will maintain. The humidifier will automatically stop misting when the room reaches the target humidity level.

1. Press repeatedly to set a humidity level between 40% and 80% Relative Humidity (RH).

2. The display will flash 3 times to confirm your selection, then return to showing the current humidity percentage in the room.
   Note:

3. The humidifier will automatically mist for 15 seconds after being turned on, even if the room has reached the set humidity level.

4. Press once to see the selected humidity level again. Keep pressing to change the humidity level.

5. You can still adjust the mist level, the timer, and the warm mist setting after setting the humidity level.

6. The humidifier will not increase the mist level when a humidity level percentage is set, only stop misting once the set humidity level is reached. If you want the humidity in your room to increase faster, set the humidifier to high mist level.

7. Once the humidity of the environment reaches the humidity you set, the humidifier will automatically stop misting.

8. The humidifier will continue detecting the humidity level in the room. It will start misting again when the humidity drops to 5% below the set level.

Note:

• To cancel the set humidity level, press and hold for 2 seconds, which will set the humidity level to “–“. The display will flash 3 times to confirm, then return to showing the current humidity percentage in the room.
• When the humidity level is set to “–” the humidifier will automatically keep misting at the current mist level until it runs out of water.

Timer
You can set an auto-shutoff timer between 1 and 12 hours.

• Press repeatedly to choose a time in increments of 1 hour. When you stop pressing  . the display will flash 3 times and the timer will start.
• The humidifier will automatically power off once the timer is finished.
• To cancel a timer, press and hold for 3 seconds. You can also press repeatedly until the display reads”–” or use the VeSync app.

Sleep Mode
Sleep Mode changes the humidifier’s mist setting to an automatic mode and turns off the display lights.

• Press to turn Sleep Mode on/off.
• Sleep Mode automatically turns off warm mist to reduce noise. You can press to turn warm mist back on.
• Sleep Mode uses the humidity sensor to detect the relative humidity in the room and automatically adjusts the mist level to maintain 50-60% relative humidity.

• When Sleep Mode is on, you can press any button to wake up the display. If you stop touching the display, the display will turn off again after 6 seconds.
• When Sleep Mode is on, you can use all other settings except changing the mist level or humidity level. If you change the mist level or humidity level, Sleep Mode will turn off.
• When Sleep Mode is turned on, the humidifier will automatically mist for 15 seconds, even if the room’s humidity level is over 60%.

Turning Off the Display
The display will automatically dim after 30 seconds of inactivity.

• To turn off the display, press and hold for 3 seconds.
• To turn the display back on, press any button.

Using the Aroma Box
Your humidifier can be used for aromatherapy.

1. Push the aroma box at the back of the base and pull it out. [Figure 3.3]
2. Put 8-10 drops of essential oils on the aroma pad. [Figure 3.4]
3. Place the aroma box back into the humidifier.
4. Turn on the humidifier. The humidifier will automatically diffuse aroma when used.

Note:

• Do not add essential oils, water treatment liquids, or third-party water filters into the water tank or base chamber. Only add essential oils to the
  aroma pad. [Figure 3.5]

• The aroma pads can be cleaned and reused after diffusing essential oils (see Cleaning the Aroma Pad, page 20).

• This humidifier uses a small heat-based aroma diffuser. The aroma is intended to be light.

• For information on replacement aroma pads, see page 20.

Absorption Pads
The mineral absorption pads help reduce mineral buildup (scale) inside the humidifier, especially on the heating element.

Note : For information on replacement absorption pads, see page 20.

Memory Function

• The humidifier will remember your settings for Mist Level, Humidity Level, Warm Mist, and Wi-Fi settings when turned off or unplugged, and will resume those settings when turned back on.
• The humidifier will not remember Sleep or Timer settings, and the display will automatically turn back on when the humidifier is turned back on.

Automatic Shutoff
The humidifier will automatically turn off when all of the water in the tank has been diffused. will show on the display and blink 10 times before the humidifier turns off. Fill the water tank (see Getting Started, page 9).
If the tank has been removed from the base, the humidifier will automatically stop misting. will show on the display, and will turn off once the tank is placed properly back on the base.IMPORTANT TIPS
Your humidifier must have the correct level of water in the base chamber to work properly. If there is too much water in the base chamber, the humidifier cannot create mist.

VeSync App Functions
The VeSync app allows you to access additional smart functions, including those listed below.

Remote Control From Your Phone

• Turn the humidifier on/off.
• Cycle through mist levels and heat levels, and turn Sleep Mode on/off.
• Turn the display lights on/off.

Monitor Humidity Levels
Check current humidity levels in the humidifier’s environment.

Set Timers & Schedules
Program individual timers or create a schedule for your smart humidifier.

Third-Party Voice Control
Compatible with Amazon Alexa and Google Assistant'” for voice commands.

Note : The VeSync opp is continually updated and opp features will expand.

IMPORTANT TIPS
Your humidifier must have the correct level of water in the base chamber to work properly. If there is too much water in the base chamber, the humidifier cannot create mist.

• Do not place the humidifier on an inclined surface.
• Never pour water directly into the base chamber. [Figure 4.1) Only add water to the water tank. The humidifier will automatically release the correct amount of water into the base chamber.
• Avoid moving or shaking the humidifier. This may cause the water tank to release too much water into the base chamber.
• Before moving the humidifier, turn it off, unplug it, and remove the water tank. Empty any excess water from the base chamber.

CARE & MAINTENANCE

Note:

• All maintenance should be done on a water-resistant surface, such as a kitchen counter.
• Change the water daily to avoid bacteria growth.
• Use a tissue or cloth to clean the nozzles regularly.
• If not using the humidifier for 1 week or longer, do not leave water inside. Clean and dry the humidifier instead.
• For more safety information, see Maintenance Safety (page 5).

Cleaning
You should clean your humidifier water tank and base chamber every 3 days, and when you’re ready to store it.

Note:

• Never immerse the base in water or liquid. Do not place any part of the humidifier in a dishwasher.
• Do not use detergents to clean the humidifier.

1. Unplug the humidifier.
   Note : If you’ve been using the warm mist setting, allow the humidifier to cool before cleaning.

2. Remove and rinse the water tank cover.

3. Remove the water tank from the base, and remove the mist channel and mist tube. [Figure 5.1] Pour out any water from the tank and base chamber. If you’ve used the warm mist setting, use caution in case the water is still hot.
   Note : When pouring out water, hold down the float to ensure that it does not fall out of the base chamber.

4. Remove the water filter from the tank by rotating it anticlockwise and lifting it out. [Figure 5.2]

5. Remove the water filter sponge from the water filter if necessary for cleaning.

6. Detach the mist tube from the mist channel by twisting the tube anticlockwise.

7. Remove the float, noise silencer, absorption pad, and aroma box from the base.

8. Detach the outer water outlet valve from the tank by rotating it anticlockwise.

9. Rinse all parts (except the outside of the base) with room temperature water.

10. To descale the humidifier (remove mineral buildup):

11. a. Remove the wate r fi lte r and the water outlet va lve from the tank. Remove the noise silencer and absorption pad from the base. Keep the mist tube and mist channel in place.

12. b. Fill the tank with 710 ml/ 3 US cups of disti lled wh i te vinegar.

13. c. Replace the tank cover and swish the vinegar around the tank.

14. d. Place the tank on the base and soak for 15-20 minutes. Vinegar will drai n into the base chamber and loosen scale (m i neral buildup) in the tank and i n the base chamber (includi ng the transducer and float).

15. e. Remove the tank, remove the tank cover, and pour out any vinegar.

16. f. Remove the float from the base chamber by pulli ng up the larger side of the float and pulling the shaft out from the float brackets. One side of the float brackets is open (U-shaped) to allow the shaft to be removed. [Figure 5.6]

17. g. Place the float, water fi lter. water outlet valve, aroma box, and noise silencer in a container. Fill with enough vinegar to cover them. Soak for 15-20 minutes.

18. h. Use a soft cloth and the included cleaning brush to remove scale from all parts. [Figure 5.7]

19. i. Rinse all parts until any vinegar smell is completely gone.

20. Dry all parts with a cloth. Make sure all parts are completely dry before reassembling or storing

Cleaning the Aroma Pad & Absorption Pad

1. Pull out the aroma box and remove the aroma pad. [Figure 5.8]
2. Remove the noise silencer, then remove the absorption pad from on top of the heating element. [Figure 5.9]
3. Rinse the pads under warm, running water.
4. Dry the pads with a clean cloth.
5. Place the aroma pad back into the aroma box.
6. Place the absorption pad back into the base.

Note : Do not use liquid cleaners or detergents to clean the pads or any other part of the humidifier.

Replacing the Aroma Pad & Absorption Pad
If the aroma pad or absorption pad is stiff even after cleaning, then it needs to be replaced. Extra pads are included with the humidifier. To maintain the performance of your humidifier, only use official Levoit aroma pads and absorption pads. For more information, contact Customer Support (see page 27).

Reassembling

1. Place the float back into the base chamber: [Figure 5.9]
2. a. Make sure the correct side of the float is facing up.
3. b. Insert the smaller prong into the closed side of the float brackets.
4. c. Place the larger prong into the open (U-shaped) side of the float brackets.
5. Place the absorption pad and the noise silencer back over the heating element. [Figure 5.10]
6. Screw the mist tube back onto the mist channel by twisting the tube clockwise. Place securely into place back over the base chamber. [Figure 5.10]
7. Place the outer water outlet valve back onto the tank by rotating it. [Figure 5.11]
8. Make sure the water filter sponge is securely placed inside the water filter. Place the water filter back into the tank and rotate it clockwise to secure it in place. [Figure 5.12]
9. Refill the tank, if necessary. Place the tank properly on the base and place the tank cover on the water tank.

Storing
Follow the cleaning instructions (see page 17) and allow all parts to dry completely before storing. Store in a cool, dry location.

TROUBLESHOOTING

Humidifier doesn’t turn on, or turns off unexpectedly.| Plug the humidifier into a working outlet and turn it on.
Add purified water to the water tank.
Little or no mist comes out.| Turn the mist level to a higher setting.
Fill the water tank.
There may be too much water in the base chamber. Empty the base chamber. Refill the water tank (not the base chamber) and place the water tank properly onto the base.
Make sure the air inlets on the bottom of the base and in the aroma box are not blocked. The humidifier should not be set on carpet or other surfaces that may block the air inlets.
Clean the humidifier (see Care & Maintenance, page 17). Make sure the nozzles are not blocked or clogged.
Make sure the humidifier is on a level surface.
If the water tank or base was washed with detergent, rinse thoroughly with clean water to remove any detergent.
Clean the water filter (see page 17) or replace the water filter sponge

with a new one. One replacement water filter sponge is included with this humidifier. For information on additional replacements. contact Customer Support (see page 27).

Humidifier uses water too quickly.| The humidifier uses up water based on the environmental temperature and humidity. If your environment is cold and/or dry, the humidifier will run out of water faster.
Using the warm mist function will use up water faster.
Humidifier produces an unusual smell.| If the humidifier is new, unplug and rinse all parts, then place in a cool, dry place for 12 hours.
If essential oils were placed on the aroma pad, rinse the pad under clean water and allow it to dry.
Clean the humidifier (see Care & **Maintenance,** page 17).

Humidifier makes a loud or unusual noise.| Make sure the water tank is properly in place (see G e tting Started , page

9).

Set mist level to a lower setting.
Empty the base chamber. Refill the water tank (not the base chamber) and place the water tank properly onto the base.

When using the warm mist function, the heating element may make a gurgling noise if the water level is low. Add more water to the water tank.

The humidifier may be malfunctioning. Stop using the humidifier and contact Customer Support (see page 27).
Mist leaks from the base.| Make sure the water tank is properly in place (see Getting Started , page

White dust appears around or in the humidifier.| ****

We recommend using purified water to fill the humidifier. Avoid using water with high mineral content. such as tap water.

Clean the humidifier (see Ca r e & **Maintenance , page 17).
Water visibly leaks from the humidifier.| Avoid running the humidifier in a room with over 60% relative humidity.
Wipe any excess water off the top and bottom of the base.
Do not shake the humidifier.
Make sure to place the humidifier on a flat, level surface.
Check the water tank for leaks. If there are leaks, contact Customer Support (see page 27).
The area around the humidifier is damp or wet from condensation.| Humidity may be too high. Turn down the mist level, turn off the humidifier, or open a door or window to the room.
Open a window to ensure proper airflow for the humidifier, or move the humidifier to a more well-ventilated room.
Make sure the water tank is properly in place (see Getting Started ,** page 9).
When replacing the water tank, wipe off excess water from the water tank and base.

Mist is not warm after pressing .| ****

Allow the humidifier to heat up for about 15 minutes to produce warm mist.

Clean the heating element (see Care & Maintenance.

page 17).

The mist is warm on the cool mist setting.| The heating element may still be warm after being used for warm mist. Allow the heating element to cool for at least 30 minutes.
Mould grows inside the humidifier.| Clean the water tank and base chamber regularly (see Care &

Maintenance, page 17).

G) lights up red.| Fill the water tank.
Place the water tank properly on the base.
Clean the water filter (see page 17) or replace it with a new one. To request a new water filter, contact Customer Support (see page 27).
Essential oil has little or no smell.| ****

Add more essential oil. For best results, use pure essential oil.

Display shows an incorrect humidity percentage.| The room may be larger than the humidifier’s effective range. Move to a room smaller than 40-70 m2 / 430-753 ft2.
Moisture may have built up inside the humidity sensor. Make sure the nozzles are facing away from the aroma box so that mist does not settle on the sensor inside the aroma box (see diagram in Getting To Know Your Smart Humidifier , page 6). Turn off the humidifier, remove the aroma

box, and allow the sensor to air dry.

If the humidifier is placed within 30 cm/ 12 inches of a wall or in a corner, the humidity sensor cannot provide a proper reading for the relative humidity in the room.
The humidity sensor will give an improper reading if it is exposed to dust. Avoid using the humidifier in dusty rooms. Avoid using tap water in the humidifier, as this can increase dust in the air.
The humidity level isn’t changing in my room.| ****

Use a higher mist level setting.

Depending on your environment, the humidifier may take longer to humidify your air.
The room may be larger than the humidifier”s effective range. If the room is larger than 40-70 m2 / 430-753 ft2, the humidifier will not be as effective.
Display shows Error Code “E1 “ , “E2”, “E3”, “E4”, or “E6”.|

The humidifier is malfunctioning. Contact Customer Support (see page page 27).

VESYNC APP TROUBLESHOOTING

Why isn’t my humidifier connecting to the VeSync app?

• Make sure your phone has Bluetooth® turned on and is not currently connected to another Bluetooth device.
• During the setup process, you must be on a secure 2.4GHz Wi-Fi network. Confirm that the network is working correctly.
• Make sure the Wi-Fi password you entered is correct.
• Make sure your humidifier and phone are within 10 m / 30 ft of each other.
• Reset the humidifier by pressing and holding for 15 seconds. Then try connecting again.

My humidifier is offline.

• Make sure the humidifier is plugged in. The humidifier may appear to be offline if it is unplugged, or if the outlet does not have power.
• Refresh the VeSync menu by swiping down on the screen.
• Make sure your router is connected to the internet and your phone’s network connection is working.
• Reset the humidifier using one of these options:
  • a. Delete the humidifier from the VeSync app. Swipe left (iOS0) or press and hold (Android), then tap Delete. Then reconfigure your humidifier with the VeSync app.
  • b. Press and hold C) for 15 seconds. Then reconfigure your humidifier with the VeSync app.

Note : Power outages, internet outages, or changing Wi-Fi routers may ca use you r humidifier togo offline.

The VeSync app is displaying an incorrect humidity percentage while the humidifier is turned on.

• The room may be larger than the humidifier’s effective range. Move to a room smaller than 40-70 m2 I 430-753 ft2
• Moisture may have built up inside the humidity sensor. Make sure the nozzles are facing away from the aroma box so that mist does not settle on the sensor inside the aroma box (see diagram in Getting To Know Your Smart Humidifier, page 6). Turn off the humidifier, remove the aroma box, and allow the sensor to air dry.
• If the humidifier is placed within 30 cm/ 12 inches of a wall or in a corner, the humidity sensor cannot provide a proper reading for the relative humidity in the room.
• The humidity sensor will give an improper reading if it is exposed to dust. Avoid using the humidifier in dusty rooms.

If your problem is not listed, please contact Customer Support (see page 27).

DECLARATION OF CONFORMITY

Arovast Corporation hereby declares that this product is in compliance with the essential requirements and other relevant provisions of Directive 2014/53/EU, UK Radio Equipment Regulations 2017, and all other applicable EU directive requirements. The complete declaration of conformity can be found at: https://levoit.com/euro/compliance

ATTRIBUTIONS

Apple App Store is a trademark of Apple Inc. Google, Android, and Google Play are trademarks of Google LLC. Wi-Fi® is a registered trademark of Wi-Fi Alliance®. Amazon, Alexa and all related logos are trademarks of Amazon.com, Inc. or its affiliates. iOS is a registered trademark of Cisco Systems, Inc. and/or its affiliates in the United States and certain other countries. The Bluetooth® word mark and logos are registered trademarks owned by Bluetooth SIG, Inc. and any use of such marks by Arovast Corporation is under license. Other trademarks and trade names are those of their respective owners.

WARRANTY INFORMATION

Product| Smart Hybrid Ultrasonic

Humidifier

---|---
Mod e l| LUH-A602S-WEU
For your own reference, we strongly recommend

that you record your order ID and date of purchase .

Ord e r ID I
Date of Purchase I

Terms & Policy
Arovast Corporation warrants all products to be of the highest quality in material, craftsmanship, and service for 2 years, effective from the date of purchase to the end of the warranty period. Warranty lengths may vary between product categories.If you have any questions or concerns about your new product, please  contact our helpful Customer Support Team.

CUSTOMER SUPPORT

Arovast Corporation 1202 N. Miller St., Suite A Anaheim, CA 92806 USA Email: support.eu@levoit.com

Please have your order invoice and order ID ready before contacting Customer Support.

SPECIFICATION

Installed), 3 Absorption Pad (1 Pre-Installed), 2x Water Filter Sponge (1 Pre-Installed), 1 Cleaning Brush, 1 User Manual, 1 Quick Start Guide
Power Supply| AC 220-240V, 50/60Hz
Rated Power| 280W
Water Tank Capacity| 6 L / 1.32 gal
Max Cool Mist Output| 300 ml/h
Max Warm Mist Output| 550 mL/h
Max Run Time| 50 hours on low mist setting
Noise Level| Lowest: < 28dB (Low Cool Mist), Highest: < 40dB (High Warm Mist)
Effective Range| 40-70 m2 / 430-753 ft2
Dimensions| 29.4 x 19.5 x 28.8 cm / 11.6 x 7.7 x 11.3 in
Weight| 2.7 kg/ 6 lb
Wi-Fi® Frequency Range| 2412-2472MHz, E.I.R.P.: 19.0 dBm
Bluetooth® Frequency Range| 2402-2480MHz, E.I.R.P.: 10.0 dBm

FAQS

What is the water tank capacity of the Levoit LV600S Smart Hybrid Ultrasonic Humidifier?

The water tank capacity of the Levoit LV600S Smart Hybrid Ultrasonic Humidifier is 6 liters or 1.32 gallons.

How long can the humidifier run on low mist setting?

The humidifier can run for up to 50 hours on low mist setting.

Does the humidifier have Wi-Fi and Bluetooth capabilities?

Yes, the humidifier is equipped with Wi-Fi and Bluetooth capabilities, allowing you to control it remotely using the VeSync app.

Can I add essential oils to the water tank or base chamber?

No, you should not add essential oils, supplemental water treatment liquids, or water filters into the water tank or base chamber. This will damage the humidifier and cause leaks. Only add essential oils to the aroma pad.

How often should I clean the water tank and base chamber?

You should clean the water tank and base chamber every 3 days or less.

Can children use this humidifier?

This humidifier can be used by children 8 years and older as well as persons with reduced physical, sensory, or mental capabilities or lack of experience and knowledge if they have been given supervision or instruction concerning use of the humidifier in a safe way and understand the hazards involved. Supervise children when they are near the humidifier.

What should I do if the humidifier is damaged or not functioning properly?

If the humidifier is damaged or is not functioning properly, stop using it and contact Customer Support immediately (see page 27).

Can I use other liquids besides clean water in the water tank?

No, you should only fill the water tank with clean water. Never fill the water tank with any other liquids.

Can I place the humidifier near sources of heat?

No, you should not place the humidifier near sources of heat, such as stovetops, ovens, or radiators.

Can I cover the nozzles while the humidifier is on?

No, you should not cover the nozzles while the humidifier is on. Doing so may damage the humidifier.

Read User Manual Online (PDF format)

Read User Manual Online (PDF format)  >>

Download This Manual (PDF format)

Download this manual  >>