SHEFFIELD HOME U12Q LED Table Lamp Instruction Manual
- June 6, 2024
- SHEFFIELD HOME
Table of Contents
SHEFFIELD HOME U12Q LED Table Lamp
SAVE THESE INSTRUCTIONS AND READ CAREFULLY BEFORE USE For Customer Care, production operation information or problem resolution, call toll-free 1.800.936-3213
IMPORTANT SAFETY INSTRUCTIONS
WARNING : To prevent electric shock, make sure the clock is not plugged in until all steps are complete.
WARNING : TO REDUCE THE RISK OF FIRE, ELECTRIC SHOCK, OR INJURY TO PERSONS Turn clock off and WAIT UNTIL NIGHT LIGHT (B) AND ADAPTER (C) ARE COOL before handling.
- The LED panel (D) might get hot after several hours of continuous use. DO NOT place your hands directly on LED light panel.
- Never use with an extension cord unless the plug can be fully inserted into the receptacles in the extension cord.
- Do not alter the plug.
- The lamp head included with this unit cannot be replaced by the consumer.
- Do not place flammable material near or over the lamp.
- Ensure the lamp is not installed next to any air vents and is not in any moist or damp areas.
- INDOOR USE ONLY
NOTE : The important safety instructions appearing in this manual are not meant to cover all possible conditions and situations that may occur. It must be understood that common sense, caution, and care must be used with any electrical product.
CAUTION : Any change or modification to this product not expressly recognized by Enchante Lites LLC voids Enchante’s responsibility for proper/unction of product.
A
B
| Lamp Base
Lamp Body
---|---
C| Lamp Shade
D
E
| LED Panel
Power Adapter Input
F
G
H
| Power Connector
Power Adapter Power Switch
I| Mode Switch
J
K
| Arrow Up
Arrow Down
L| Charger
INSTRUCTIONS
NOTE : THIS UNIT IS FULLY ASSEMBLED
-
Remove lamp from packing, placing lamp base (A) flat on a steady surface.
-
Connect power connector (F) into power adapter input (E) at the rear-bottom of the lamp.
-
Plug the power adapter (G) into a standard household 120V AC outlet.
NOTE : Only use with the supplied power adapter to avoid damage or risk of fire. -
Power switch (H) is a touch-activated switch that controls ON/OFF power.
-
Brightness switch (I) is a touch-activated switch that controls the LED brightness settings.
-
Arrow switch (J) is a touch-activated switch that controls the CCT (correlated color temperature) function of the lamp.
-
To begin, gently tap power switch (H) to achieve the following:
-
One tap:Turns lamp ON to default 1st brightness setting
-
Two taps:Turns lamp OFF
-
To adjust brightness, gently tap arrow switch (J) to turn the brightness up and tap arrow switch (K) to turn the brightness down.
-
This lamp features three color modes. To adjust lighting color mode, tap the power switch (H) to turn ON lamp, then tap mode switch (I) to toggle between light color temperatures (3000K, 4200K, 5500K) until desired setting is reached.
-
To reposition the light, hold base (A) steady and grasp either lamp body (B) or shade (C) depending on necessary adjustment.
-
Center your device on the Qi wireless charging pad (L) and a red indicator light on top of the base will indicate charging. lf the red indicator light begins to flash, your device may not be centered on the charger. Once the indicator light turns green, charging is complete.
NOTE : DO NOT FORCE the shade outside allowable adjustable range as excessive adjustment may cause damage.
PRODUCT SPECIFICATIONS
Input:| 12V
Dimmable:| 5 Levels
LED Lifespan:| 15,000 Hours
LED Specification:| 8W400Im SMD
Correlated Color Temperature ((CT):| Warm (3000K)
Natural (4200K) Cool White (SSOOK)
PRODUCT MAINTENANCE
- Always ensure the power is OFF and the clock has cooled down before performing any maintenance, cleaning or adjustments
- To avoid injury or damage to the clock, ensure that the adapter and any screws are secure before reconnecting to power.
- To clean, wipe with a damp or dry clean cloth. Never soak the clock with water.
FCC Warning
This device complies with part 15 of the FCC rules. Operation is subject to
the following two conditions: (1) this device may not cause harmful
interference, and (2) this device must accept any inte rference received,
including interference that may cause undesired operation. Changes or
modifications not expressly approved by the party responsible for compliance
could void the user’s authority to operate the equipment.
NOTE : This equipment has been tested and found to comply with the limits
for a Class B digital device, pursuant to part 15 of the FCC Rules. These
limits are designed to provide reasonable protection against harmful
interference in a residential installation. This equipment generates uses and
can radiate radio frequency energy and, if not installed and used in
accordance with the instructions, may cause harmful interference to radio
communications. However, there is no guarantee that interference will not
occur in a particular installation. If this equipment does cause harmful
interferenceto radio or television reception, which can be determined by
turning the equipment off and on, the user is encouraged to try to correct the
interference by one or more of the following measures:
- Reorient or relocate the receiving antenna.
- Increase the separation between the equipment and receiver.
- Connect the equipment into an outlet on a circuit different from that to which the receiver is connected.
- Consult the dealer or an experienced radio/TV technician for help.
Radiation Exposure Statement
This equipment complies with FCC radiation exposure limits set forth for an
uncontrolled environment. This equipment should be installed and operated with
minimum distance 20cm between the radiator and your body.
If you find that you have any trouble or missing or damaged parts please
contact us.
If you need installation assistance, replacement parts or have questions
regarding our warranty, please contact our product consultants at
customersupport@enchlites.com or call
toll free:
1-800-936-3213 Monday to Friday from
9:00 a.m. to 6:00 p.m., EST. English and Spanish spoken. International
Regions: Please contact your local distributer.