INSERTO-ELETTRICO Cornice Fuego Monica 1500w Wenghe Instruction Manual
- June 27, 2024
- Fuego
Table of Contents
INSERTO-ELETTRICO Cornice Fuego Monica 1500w Wenghe
Product Information
Specifications
- Voltage: 220-240V~
- Heating power: High: 1500W; Low: 750W
- Frequency: 50/60Hz
- Power connection: Non-detachable cable with Y-type plug
Product Usage Instructions
Cleaning the Exterior of the Appliance
Before cleaning the appliance, disconnect it from the power outlet and let it cool down. Do not use cleaning or polishing products. Avoid risks associated with unintentional thermal cut restoration by not powering the appliance through an external switching device like a timer.
Unpacking Operations
Handle the product with care to avoid glass breakage. It is recommended to place the fireplace on a carpet during assembly rather than directly on the floor.
Installation Instructions
Hole size for inserting the fireplace should be noted. Ensure the support platform is flat, complete, and sturdy. The power outlet must be grounded.
Front Functional Area
Safety advice: To prevent fires, do not place anything within 100mm in front of the hot air outlet grille.
Configuration Information
- Nominal Voltage: 220-240V~
- Nominal Frequency: 50/60Hz
- Display Power: 10W-300W
- Nominal Power: High: 1500W; Low: 750W
Manual Button Operation
| Symbol | Name | Description |
|---|---|---|
| Power | On/Off | Turn the fireplace on/off |
| Temperature | Temperature | Adjust the temperature from 19-30 |
| Timer | Timer | Timing: 30min-1h-2h-3h-4h-5h-6h-7h-8h30min |
| Flame | Flame | Flame from 1 to 6 levels |
Manual Button Operation
| Symbol | Name | Description |
|---|---|---|
| Power On/Off | Turn on/off the fireplace | |
| Temperature | Adjust temperature between 19-30 degrees |
Remote Control Functions
Note: The remote control buttons with the crossed-out symbols are not active in these models.
Digital display on the fireplace:
- F1: Default. F1-F2-F3-F4-F5-F6-F1. The number corresponds to the display.
Remote Control Operation
On/Off: Press this button to turn on the screen with F1. Press this button to turn off the appliance without anything appearing on the screen.
Temperature: Press briefly to reduce by 1 degree. If it rises to a certain temperature, the heating turns off when it rises by 1 degree. Reducing to a certain temperature, the heating turns on when it reduces by 2 degrees.
Timer: Weekly timer On/Off. Press the button to activate/deactivate the weekly timer function.
Information Requirements for Local Electric Heaters
| Model Identifier(s) | FUEGO-INSERTO-ELETTRICO |
|---|---|
| Item | Symbol |
| Nominal Heat Output | Pnom |
| Minimum Heat Output (indicative) | Pmin |
| Maximum Continuous Heat Output | Pmax,c |
| At Nominal Heat Output | elmax |
| At Minimum Heat Output | elmin |
| In Standby Mode | elsb |
Contact Details
Production: Suzhou Yueyu Thermal Energy Technology Co.
Factory Address: No. 6 Xinghai Road, Liuhe, Taicang, Taicang City, City Suzhou, Jiangsu, China
Made in China Imported in Italy by M.P.C. srl Via Tortona 20144 Milano Italia
Tel +39 02 21117815
Email: [email protected]
Website: www.sinedtechnology.com
Trademark MPC and logo MPC are registered by M.P.C. srl
Troubleshooting
| Issue | Solution |
|---|---|
| Poor contact between plug and socket | Correctly plug in or replace the plug |
| Overheating | Turn off and let cool for 15 minutes |
| Overheating protection does not deactivate | Contact after-sales service |
| Heating without flames | Contact after-sales service |
| Flames without heating | Turn on the heating |
| Remote control not responding | Move closer to the fireplace and position |
yourself in front
Flames with noise| Contact after-sales service
FAQs
Can I use cleaning products on the exterior of the appliance?
Avoid using cleaning or polishing products on the appliance. Only clean with a dry cloth.
What should I do if the glass breaks during handling?
Handle the product with care to prevent glass breakage. In case of breakage, contact customer support for assistance.
What should I do if the fireplace overheats?
Turn off the fireplace and let it cool for 15 minutes. If the overheating protection does not deactivate, contact after-sales service.
How do I clean the fireplace?
Unplug the fireplace from the power outlet and let it cool down before cleaning. Do not use cleaning or polishing products.
What should I do if the remote control is not responding?
Move closer to the fireplace and position yourself in front of it. If the problem persists, contact after-sales service.
Can I use an external switching device to power the fireplace?
No, to avoid risks due to accidental resetting of the thermal cut-off, the appliance must not be powered through an external switching device, such as a timer, or connected to a circuit that is regularly switched on and off by the power grid.
What are the dimensions of the opening required for installation?
The exact dimensions of the opening are width 584 x height 495 (mm). It is recommended to add a tolerance of +3 mm to the width and height.
Made in China Imported in Italy by M.P.C. srl Via Tortona 20144 Milano
Tel +39 02 21117815 / [email protected] / www.sinedtechnology.com
Trademark MPC and logo MPC are registered by M.P.C. srl