CODE 3 12+ Pro Series Lightbars Instruction Manual
- June 21, 2024
- Code 3
Table of Contents
- Installation and Operation Instructions
- 12+ Pro Vantage™ Series Lightbars
- Specifications
- Installation & Mounting
- Wiring Instructions
- Maintenance
- Lens Removal and Installation
- Warning LED Modules (EZ1203X, EZ1206XX)
- Alley / Takedown / Worklight LED Modules (EZ0003)
- Stop / Tail / Turn LED Modules (EZ1205)
- Advanced Controller (CZ1202)
- Special Features:
- Touchpad Backlight
- Safety Director Front/Rear Selection
- Advanced Control Pad Mounting:
- Advanced Controller Mount (EZ1415):
- Replacement Parts/Accessories
- Troubleshooting
- LIGHTBAR AND CONTROLLER
- ALLEY / TAKEDOWN / WORKLIGHTS
- STOP/TAIL/TURN
- Read User Manual Online (PDF format)
- Download This Manual (PDF format)
Installation and Operation Instructions
12+ Pro Vantage™ Series Lightbars
IMPORTANT! Read all instructions before installing and using. Installer: This manual must be delivered to the end user.
WARNING!
Failure to install or use this product according to manufacturer’s
recommendations may result in property damage, serious injury, and/ or death
to those you are seeking to protect!
Do not install and/or operate this safety product unless you have read and understood the safety information contained in this manual.
1. Proper installation combined with operator training in the use, care,
and maintenance of emergency warning devices are essential to ensure the
safety of emergency personnel and the public.
2. Emergency warning devices often require high electrical voltages and/or
currents. Exercise caution when working with live electrical connections.
3. This product must be properly grounded. Inadequate grounding and/or
shorting of electrical connections can cause high current arcing, which can
cause personal injury and/or severe vehicle damage, including fire.
4. Proper placement and installation is vital to the performance of this
warning device. Install this product so that output performance of the system
is maximized and the controls are placed within convenient reach of the
operator so that they can operate the system without losing eye contact with
the roadway.
5. Do not install this product or route any wires in the deployment area
of an air bag. Equipment mounted or located in an air bag deployment area may
reduce the effectiveness of the air bag or become a projectile that could
cause serious personal injury or death. Refer to the vehicle owner’s manual
for the air bag deployment area. It is the responsibility of the user/operator
to determine a suitable mounting location ensuring the safety of all
passengers inside the vehicle particularly avoiding areas of potential head
impact.
6. It is the responsibility of the vehicle operator to ensure daily that
all features of this product work correctly. In use, the vehicle operator
should ensure the projection of the warning signal is not blocked by vehicle
components (i.e., open trunks or compartment doors), people, vehicles or other
obstructions.
7. The use of this or any other warning device does not ensure all drivers
can or will observe or react to an emergency warning signal. Never take the
right-of-way for granted. It is the vehicle operator’s responsibility to be
sure they can proceed safely before entering an intersection, drive against
traffic, respond at a high rate of speed, or walk on or around traffic
lanes.
8. This equipment is intended for use by authorized personnel only. The
user is responsible for understanding and obeying all laws regarding emergency
warning devices. Therefore, the user should check all applicable city, state,
and federal laws and regulations. The manufacturer assumes no liability for
any loss resulting from the use of this warning device.
Specifications
Length……………..24”, 30”, 36”, 42”, 48”, 54”, 60”, 72”
Width……………….11”
Height………………2.5”
Voltage…………….12-24VDC
Current Draw…….Single Color LED Module = 0.55A Avg. @ 12.8VDC
Dual Color LED Module = 0.55A Avg. @ 12.8VDC
LED STT (pair) = 1.2A Avg.@ 12.8VDC
LED AL,TD,WL = 1.2A Avg. @ 12.8VDC
Flash Patterns…..70
Fuse Recommendation:
Calculate the total amp draw from all the LED Modules.
Multiply the total amp draw by 1.25. Round up to the nearest fuse.
Installation & Mounting
Unpacking and Pre-Installation
Carefully remove the lightbar and place it on a flat surface. Examine the unit for transit damage and locate all parts. If damage is found or parts are missing, contact the transit company or Code 3. Do not use damaged or broken parts. Ensure the lightbar voltage is compatible with the planned installation.
Mounting
Before proceeding with installation, plan all wiring and cable routing. Select the mounting location for the lightbar on a flat, smooth surface and center the unit across the width of the vehicle. The mounting location for the lightbar should be chosen such that the lightbar is level and visibility to approaching traffic is optimized.
CAUTION!
When drilling into any vehicle surface, make sure that the area is free
from any electrical wires, fuel lines, vehicle upholstery, etc. that could be
damaged.
Permanent Mounting with Adjustable Mounting Feet
-
Loosen the 5/16″ nuts to allow the mounting feet to slide along the base. Place the lightbar over the center of the vehicle and slide the mounting feet into position near the curved edges of the roof when possible.
-
Secure the feet in location on the lightbar by tightening the four nuts on each foot.
-
With the feet positioned, remove the adjustable foot cover and mark the location of the mounting hole centers on the roof of the vehicle.
Remove the lightbar and drill the mounting holes as marked. Note: The center distance between the mounting holes in an adjustable mounting foot is 11.1″ or 281.94 mm. -
Attach the appropriate foot pad for the curvature of the roof surface per FIGURE 2. Secure the lightbar feet to the vehicle using the supplied 1/4″-20 hardware and reattach the adjustable foot cover as shown in FIGURE 1. See the Wiring section of this manual for further wiring instructions.
Figure
1
- ADJUSTABLE FOOT COVER
- OVERSIZED FLAT WASHER
- 1/4” NYLON INSERT NUT
- VEHICLE ROOF
- RUBBER PAD
- 1/4”- 20 HEX BOLT
Figure
2
- FLAT ROOF
- WEDGE RUBBER PAD
- FLAT RUBBER PAD
- CURVED ROOF
Strap Kit Mounting
- Loosen the 5/16″ nuts to allow the mounting feet to slide along the base of the lightbar. Loosely attach the mounting strap to each foot using the supplied pan head phillips screws and lock washers.
- Center the lightbar across the vehicle and align the strap mount brackets to hook into the gutter of the vehicles door frame as shown in FIGURE 3.
- Secure the feet to the lightbar in location by tightening the four nuts on each foot.
- Slowly tighten the pan head screws to secure the strap mount brackets to the lightbar feet and around the door gutters, keeping the lightbar centered and level. Ensure the doors close completely and secure each strap mount bracket to the door frame. Mounting geometry and parts will vary for different vehicles. See the Wiring section of this manual for further wiring instructions.
IMPORTANT! Mounting brackets are specific to the vehicle model. Please make sure the brackets are suitable for the vehicle before installation.
Figure
3
- STRAP MOUNT BRACKET
- 5/16”-18 PAN HEAD PHILLIPS SCREW
- 5/16” LOCK/SPLIT WASHER
- ADJUSTABLE FOOT
- VEHICLE ROOF SECTION
- NO. 8 SHEET METAL SCREW
Wiring Instructions
IMPORTANT! This unit is a safety device and it must be connected to its own separate, fused power point to assure its continued operation should any other electrical accessory fail.
Notes:
1. Larger wires and tight connections will provide longer service life for
components. For high current wires it is highly recommended that terminal
blocks or soldered connections be used with shrink tubing to protect the
connections. Do not use insulation displacement connectors (e.g., 3M
Scotchlock type connectors).
2. Route wiring using grommets and sealant when passing through
compartment walls. Minimize the number of splices to reduce voltage drop. All
wiring should conform to the minimum wire size and other recommendations of
the manufacturer and be protected from moving parts and hot surfaces. Looms,
grommets, cable ties, and similar installation hardware should be used to
anchor and protect all wiring.
3. Fuses or circuit breakers should be located as close to the power
takeoff points as possible and properly sized to protect the wiring and
devices.
4. Particular attention should be paid to the location and method of
making electrical connections and splices to protect these points from
corrosion and loss of conductivity.
5. Ground termination should only be made to substantial chassis
components, preferably directly to the vehicle battery.
6. Circuit breakers are very sensitive to high temperatures and will
“false trip” when mounted in hot environments or operated close to their
capacity.
CAUTION!
This strobe power supply is a high voltage device. To avoid the risk of
electrical shock, wait 5 minutes after turning off power before removing the
lens for access to internal parts of the strobe head.
General Wiring Instructions
Before attempting to connect the lightbar wiring harness, refer to the wiring diagram illustrated below. The wiring diagram describes the function for each separate wire.
- Route the lightbar power cable’s red wire to a fused, ignition-switched power point. Connect the black wire to a solid ground connection on the vehicle (ideally, directly to the battery negative terminal). Use a fuse according to the wiring diagram.
- After the lightbar has been mounted, route the control cable into the vehicle to the switch panel/controller location.
- Connect the wires of the lightbar wiring harness to the switched side of each switch, or plug into optional controller. See the wiring diagram for wire color/function legend.
- Use cable ties and grommets to secure and protect all cables and wires.
STANDARD WIRING (Discrete cables for power/ground and control)
- 12+ Pro Vantage™ Lightbar
- Control Cable
- Pigtal connector (ER0021)
- Switches or control box
- BROWN (PATTERN 1)
- ORANGE (PATTERN 2)
- YELLOW (ALLEY LEFT)
- GREEN (ALLEY RIGHT)
- BLUE (WORKLIGHTS/TAKEDOWNS)
- VIOLET (PROGRAM PATTERNS)
- NOTE: Combine Brown and Orange wires for Pattern 3
- IGNITION SWITCH
- See Fuse Recommendations on Page 1.
- RED
- BLACK
- Power/Ground Cable
- STTs OPTIONAL Optional Stop/Tail/Turn (STT) Cable
- BROWN (TAIL)
- YELLOW (LEFT TURN)
- GREEN (RIGHT TURN)
- RED (STOP)
- WHITE (STT GROUND)
- NOTE: GREEN AND YELLOW WIRE FUNCTIONS ARE SWAPPED IN LIGHTBARS WITH PASSENGER SIDE CABLE EXIT. USE THE RED WIRE IN 3-WIRE SYSTEMS ONLY
Programming Standard and Combined Power/Signal Cables
To change the flash pattern, apply power to the desired Pattern Wire. Next, double-tap the violet wire to power to enter pattern selection mode. Single- tap the violet wire to power to cycle through flash patterns. Isolate the violet wire once pattern selections are complete.
COMBINED POWER/SIGNAL CABLE
- 12+ Pro Vantage™ Lightbar
- Combined power/signal power
- BLACK (GROUND)
- BROWN (PATTERN 1)
- ORANGE (PATTERN 2)
- YELLOW (ALLEY LEFT)
- GREEN (ALLEY RIGHT)
- GREY (ARROWSTICK LEFT)
- WHITE (ARROWSTICK RIGHT)
- BLUE (WORKLIGHTS/TAKEDOWNS)
- VIOLET (PROGRAM PATTERNS)
- *Brown + Orange = Pattern 3
- IGNITION SWITCH
- NOTE: See Fuse Recommendations on Page 1.
- NOTE: Combine Brown and Orange wires for Pattern 3
- WHITE (STT GROUND)
- RED (STOP)
- GREEN (RIGHT TURN)
- YELLOW (LEFT TURN)
- BROWN (TAIL)
- STTs OPTIONAL Optional Stop/Tail/Turn (STT) Cable
- NOTE: GREEN AND YELLOW WIRE FUNCTIONS ARE SWAPPED IN LIGHTBARS WITH PASSENGER SIDE CABLE EXIT. USE THE RED WIRE IN 3-WIRE SYSTEMS ONLY
ADVANCED CONTROLLER (CZ1202)
- 12+ Pro Vantage™ Lightbar
- 4-Pin Cable
- Power/Ground Cable
- BLACK
- RED
- See Fuse Recommendations on Page 1.
- IGNITION SWITCH
- STTs OPTIONAL Optional Stop/Tail/Turn (STT) Cable
- BROWN (TAIL)
- YELLOW (LEFT TURN)
- GREEN (RIGHT TURN)
- RED (STOP)
- WHITE (STT GROUND)
- NOTE: GREEN AND YELLOW WIRE FUNCTIONS ARE SWAPPED IN LIGHTBARS WITH PASSENGER SIDE CABLE EXIT. USE THE RED WIRE IN 3-WIRE SYSTEMS ONLY
SERIAL INTERFACE BOX (EZMATSIB)
- 12+ Pro Vantage™ Lightbar
- 4-Pin Cable
- BLACK
- RED
- BLUE
- YELLOW
- SIB
- Power/Ground Cable
- See Fuse Recommendations on Page 1.
- IGNITION SWITCH
- 1-2 A
- GRAY/BLACK – Ignition Wire
- YELLOW – Left Alley
- PURPLE – Right Alley
- GRAY – Worklights
- ORANGE/BLACK – Takedown Lights
- PINK – Arrowstik Left
- ORANGE – Arrowstik Right
- YELLOW/BLACK – Arrowstik Flash
- GREEN/BLACK – Level 1
- WHITE/BLACK – Level 2
- RED/BLACK – Level 3
- BLUE/BLACK – Rear Cut
- PURPLE/BLACK – Front Cut
- BROWN – Left Cut
- GREEN – Cruise
- BLUE – Dim
- BLUE/WHITE – Program Patterns
- WHITE – Arrowstik Pattern
- 1 A
- NOTE: Not all SIB input wires are used.
- WHITE (STT GROUND)
- RED (STOP)
- GREEN (RIGHT TURN)
- YELLOW (LEFT TURN)
- BROWN (TAIL)
- STTs OPTIONAL Optional Stop/Tail/Turn (STT) Cable
- NOTE: GREEN AND YELLOW WIRE FUNCTIONS ARE SWAPPED IN LIGHTBARS WITH PASSENGER SIDE CABLE EXIT. USE THE RED WIRE IN 3-WIRE SYSTEMS ONLY
12+ SPEAKER
- 2+ Pro Vantage™ Lightbar
- 14AWG RED – POWER
- 14AWG BLACK – GROUND
- 16AWG RED – SPEAKER
- 16AWG BLACK – SPEAKE
Maintenance
Occasional cleaning of the lenses will ensure optimum light output. Take care when cleaning lenses – although tough, polycarbonate scratches easily. Clean the lens and base with soap and water or a lens polish using a soft cloth. Do not use solvents as they may damage the polycarbonate. Do not subject the lightbar to high-pressure washers or automatic car washers.
Lens Removal and Installation
- Remove the screws from the lenses. Starting at one edge, pull the lens off.
- Carefully lift the lens off the seal – choose a suitable location to temporarily store the lens so as to not scratch the surface.
- When reinstalling, gently apply pressure around the lens taking care not to damage the seal. Replace the screws.
Warning LED Modules (EZ1203X, EZ1206XX)
The LED lightheads have been designed to ensure long service life using high
performance LEDs. The modules are low profile units that have a high intensity
output with low current draw.
The LED lightheads can be mounted in the front, rear and corners of the
lightbar.
Alley / Takedown / Worklight LED Modules (EZ0003)
Alley / Takedown / Worklight LED Module can be mounted anywhere in the lightbar.
Stop / Tail / Turn LED Modules (EZ1205)
Stop Tail Turn modules operate in conjunction with the vehicle tail, brake and direction indicator lights. Kit includes a pair of modules, installation hardware and wiring.
Advanced Controller (CZ1202)
Provides convenient control of the lightbar’s built-in flash patterns and features soft touch buttons and LED function indicator lights.
12+ PRO ADVANCED CONTROLLER FUNCTIONS
CODE3ESG.com
P/N CZ1202
Toggle Press [Press for 2 Seconds]
-
Cruise
-
DIM
[Back Lighting] -
Takedown
[Front Cut] -
Select
Progrom Flash Patterns -
Flash Pattern 1
Flash Pattern 2
Flash Pattern 3 -
Right Alley
[Right Cut] -
Safety Director Pattern Select
-
Work Light
[Rear Cut] -
Safety Director On/Off
-
Left Alley
[Left Cut]
“Power” – Press to cycle through three programmable flash pattern presets. Hold button down to shut down all functions. Press again to resume.
Off Pattern 1 Pattern 2 Pattern 3
“Cruise” – Press to illuminate all directional modules in steady burn mode.
“Dim Mode” – Toggle press to dim standard flash patterns. Note, this mode will not dim takedown, alley and worklights. Long-press this button for two seconds to activate or deactivate backlighting on the contrl head.
“Flash Pattern Select” – First, select Pattern 1, 2 or 3 to program by
pushing the Power Button.
Next, double press to enter flash pattern select mode and cycle one flash
pattern. The 4 corner LEDs on the controller will mimic the lightbar to give
pattern feedback. Press again once to cycle to the next flash pattern. Press
and hold for 3 seconds to return to the prior flash pattern. The lightbar will
store the last flash pattern used to the active preset. After 30 seconds of
inactivity in Select mode, the control head will automatically exit Select
mode.
“Safety Director On/Off” – Press once to turn the Safety Director on or off.
“Safety Director Pattern Select” – Once the Safety Director is activated, press this pattern select button to cycle to the next Safety Director flash pattern. There is a 5 second delay between the controller and the lightbar. Press and hold for 3 seconds to return to the prior flash pattern. The lightbar will store the last flash pattern used.
“Front Worklight (Takedown)” – Toggle press will activate/deactivate front worklight function. Long press for two seconds to activate/deactivate front cut.
“Back Worklight” – Toggle press will activate/deactivate rear worklight function. Long press for two seconds to activate/ deactivate back cut.
“Left Worklight (Alley)” – Toggle press will activate/deactivate rear left worklight function. Long press for two seconds to activate/deactivate left cut.
“Right Worklight (Alley)” – Toggle press will activate/deactivate right worklight function. Long press for two seconds to activate/deactivate right cut.
Special Features:
Touchpad Backlight
Reset the Lightbar back to Factory Setting: Press SEL button 8 times. The lightbar will flash 3 times and will reset back to factory settings.
To limit the lightbar to R65 flash patterns, press SEL 5 times and bar will flash twice.
Safety Director Module Selection
To change the number of modules used in the safety director, press and hold SD ON/OFF – tap SD FP SEL to select 5 to 10 modules. Example:
7 modules
9 modules
Safety Director Front/Rear Selection
Press SD ON/OFF to turn on the safety director.
Press and hold SD ON/OFF, once the corner LEDs light, tap SD FP SEL to cycle
front, rear or both.
Advanced Control Pad Mounting:
The advanced control pad is supplied with three mounting options: a bracket, VHB tape and hook and loop patch. The rear of the control pad is designed to allow for the cable exit to be routed five different ways to maximize installation locations. Mount the control pad in a location within convenient reach of the operator so that s/he can operate the system without losing eye contact with the roadway.
- BRACKET
- HOOK AND LOOP PATCH
- TAPE
Advanced Controller Mount (EZ1415):
This holder can easily be mounted in the cab of a vehicle using the attached suction cup. Control head is placed inside the grips. The angle of the holder can be changed using the adjustable knobs.
Standard Flash Patterns
|
J845
---|---
Number| Flash Pattern| EZ1203A
EZ1206AX| EZ1203B
EZ1206BX| EZ1203R
EZ1206RX| EZ1203W
EZ1206WX
D
| N| D| N| D| N| D| N
1
| Double 75 FPM – DEFFAULT PATTERN FOR LEVEL 1|
C1
| C1| C1| C1| C1| C1| C1| C1
2
| Title 13 Quad 65 FPM – DEFFAULT PATTERN FOR LEVEL 2|
C1
| C1| C1| C1| C1| C1| C1| C1
3
| Title 13 Double 65 FPM|
C1
| C1| C1| C1| C1| C1| C1| C1
4
| Quint Hold 75 FPM – DEFFAULT PATTERN FOR LEVEL 3|
C1
| C1| C1| C1| C1| C1| C1| C1
5
| Pulse 8 Burst 75 FPM|
C1
| C1| C1| C2| C1| C1| C1| C2
6
| Quad Alternate S S 150 FPM|
C1S
| C1S| C1S| C1S| C1S| C1S| C1S| C1S
7
| Quad Cross Alternate 150 FPM|
C1S
| C1S| C1S| C1S| C1S| C1S| C1S| C1S
8
| Double Alternate S S 150 FPM|
C1S
| C1S| C1S| C1S| C1S| C1S| C1S| C1S
9
| Double Cross Alternate 150 FPM|
C1S
| C1S| C1S| C1S| C1S| C1S| C1S| C1S
10
| Quint Hold Alternate S S 150 FPM|
C1S
| C1S| C1S| C1S| C1S| C1S| C1S| C1S
11
| Quint Hold Cross Alternate 150 FPM|
C1S
| C1S| C1S| C1S| C1S| C1S| C1S| C1S
12
| Quad Alternate S S 150 FPM Center Pulse|
C1S
| C1S| C1S| C1S| C1S| C1S| C1S| C1S
13
| Double Alternate S S 150 FPM Center Pulse|
C1S
| C1S| C1S| C1S| C1S| C1S| C1S| C1S
14
| Quint Hold Alternate S S 150 FPM Center Pulse|
C1S
| C1S| C1S| C1S| C1S| C1S| C1S| C1S
15
| Fast Rotate|
–
| –| –| –| –| –| –| –
16
| Wave Rotate|
–
| –| –| –| –| –| –| –
17
| Rotate Quad|
–
| –| –| –| –| –| –| –
18
| Fast Quad|
–
| –| –| –| –| –| –| –
19
| Airport Flash 75 FPM|
–
| –| –| –| –| –| –| –
20
| Steady White Left|
–
| –| –| –| –| –| –| –
21
| Steady White Right|
–
| –| –| –| –| –| –| –
22
| Steady White Front|
–
| –| –| –| –| –| –| –
23
| Steady White Rear|
–
| –| –| –| –| –| –| –
24
| Title 13 Steady Single Front Red|
–
| –| –| –| –| –| –| –
25
| Title 13 Steady Single Front Blue|
–
| –| –| –| –| –| –| –
26
| Title 13 Steady Single Front Red and Blue|
–
| –| –| –| –| –| –| –
27
| 4-LED, Left, 2000 with 250 off.|
–
| –| –| –| –| –| –| –
28
| 4-LED, Left Solid, 2000 with 250 off.|
–
| –| –| –| –| –| –| –
29
| 4-LED, LeftFillAndChase, 2000 with 250 off.|
–
| –| –| –| –| –| –| –
30
| 4-LED, Right, 2000 with 250 off. |
–
| –| –| –| –| –| –| –
31
| 4-LED, Right Solid, 2000 with 250 off.|
–
| –| –| –| –| –| –| –
32
| 4-LED, RightFillAndChase, 2000 with 250 off.|
–
| –| –| –| –| –| –| –
33
| 4-LED, Center Out, 1000 with 250 off, 2 repeats.|
–
| –| –| –| –| –| –| –
34
| 4-LED, Center Out Solid, 1000 with 250 off, 2 repeats.|
–
| –| –| –| –| –| –| –
35
| 4-LED, CenterFillAndChase, 1000 with 250 off, 2 repeats.|
–
| –| –| –| –| –| –| –
36
| 4-LED, Quad Flash, 1000 with 83 on and 42 off, 2 sets of 4 repeats.|
–
| –| –| –| –| –| –| –
37
| 4-LED, Wig Wag, 500 with 250 on and 250 off, 4 repeats.|
–
| –| –| –| –| –| –| –
38
| 4-LED, Alternating, 500 with 250 on and 250 off, 4 repeats.|
–
| –| –| –| –| –| –| –
39
| Reg 65 Single 120 FPM, 2.05 Hz|
C1
| C1| C1| C1| C1| C1| C1| C1
40
| Reg 65 Double 120 FPM, 2.05 Hz|
C1
| C1| C1| C1| C1| C1| C1| C1
41
| Reg 65 Triple 120 FPM, 2.05 Hz|
C1
| C1| C1| C1| C1| C1| C1| C1
42
| Reg 65 Quad 120 FPM, 2.05 Hz|
C1
| C1| C1| C1| C1| C1| C1| C1
43
| Reg 65 Burst 120 FPM, 2.05 Hz|
C1
| C1| C1| C1| C1| C1| C1| C1
44
| Reg 65 Single S S 120 FPM, 2.05 Hz|
C1
| C1| C1| C1| C1| C1| C1| C1
45
| Reg 65 Double S S 120 FPM, 2.05 Hz|
C1
| C1| C1| C1| C1| C1| C1| C1
46
| Reg 65 Triple S S 120 FPM, 2.05 Hz|
C1
| C1| C1| C1| C1| C1| C1| C1
47
| Reg 65 Quad S S 120 FPM, 2.05 Hz|
C1
| C1| C1| C1| C1| C1| C1| C1
48
| Reg 65 Burst S S 120 FPM, 2.05 Hz|
C1
| C1| C1| C1| C1| C1| C1| C1
49
| Reg 65 Single S S 120 FPM Center Pulse, 2.05 Hz|
C1
| C1| C1| C1| C1| C1| C1| C1
50
| Reg 65 Double S S 120 FPM Center Pulse, 2.05 Hz|
C1
| C1| C1| C1| C1| C1| C1| C1
51
| Reg 65 Triple S S 120 FPM Center Pulse, 2.05 Hz|
C1
| C1| C1| C1| C1| C1| C1| C1
52
| Reg 65 Quad S S 120 FPM Center Pulse, 2.05 Hz|
C1
| C1| C1| C1| C1| C1| C1| C1
53
| Reg 65 Burst S S 120 FPM Center Pulse, 2.05 Hz|
C1
| C1| C1| C1| C1| C1| C1| C1
54
| Cycle All|
–
| –| –| –| –| –| –| –
55
| Steady PWM 50|
–
| –| –| –| –| –| –|
–
| J595
---|---
Number| Flash Pattern| EZ1203A
EZ1206AX| EZ1203B
EZ1206BX| EZ1203B
EZ1206BX| EZ1203R
EZ1206RX| EZ1203W
EZ1206WX
D
| N| D| N| D| N| D| N| D| N
1
| Double 75 FPM – DEFFAULT PATTERN FOR LEVEL 1|
C1
| –| C1| –| C1| –| C1| –| C2| –
2
| Title 13 Quad 65 FPM – DEFFAULT PATTERN FOR LEVEL 2|
C1
| –| C1| –| C1| –| C1| –| C1| –
3
| Title 13 Double 65 FPM|
C1
| –| C1| –| C1| –| C1| –| C1| –
4
| Quint Hold 75 FPM – DEFFAULT PATTERN FOR LEVEL 3|
C1
| –| C1| –| C1| –| C1| –| C1| –
5
| Pulse 8 Burst 75 FPM|
C1
| –| C1| –| C1| –| C1| –| C2| –
6
| Quad Alternate S S 150 FPM|
–
| –| –| –| –| –| –| –| –| –
7
| Quad Cross Alternate 150 FPM|
–
| –| –| –| –| –| –| –| –| –
8
| Double Alternate S S 150 FPM|
–
| –| –| –| –| –| –| –| –| –
9
| Double Cross Alternate 150 FPM|
–
| –| –| –| –| –| –| –| –| –
10
| Quint Hold Alternate S S 150 FPM|
–
| –| –| –| –| –| –| –| –| –
11
| Quint Hold Cross Alternate 150 FPM|
–
| –| –| –| –| –| –| –| –| –
12
| Quad Alternate S S 150 FPM Center Pulse|
–
| –| –| –| –| –| –| –| –| –
13
| Double Alternate S S 150 FPM Center Pulse|
–
| –| –| –| –| –| –| –| –| –
14
| Quint Hold Alternate S S 150 FPM Center Pulse|
–
| –| –| –| –| –| –| –| –| –
15
| Fast Rotate|
–
| –| –| –| –| –| –| –| –| –
16
| Wave Rotate|
–
| –| –| –| –| –| –| –| –| –
17
| Rotate Quad|
–
| –| –| –| –| –| –| –| –| –
18
| Fast Quad|
–
| –| –| –| –| –| –| –| –| –
19
| Airport Flash 75 FPM|
–
| –| –| –| –| –| –| –| –| –
20
| Steady White Left|
–
| –| –| –| –| –| –| –| –| –
21
| Steady White Right|
–
| –| –| –| –| –| –| –| –| –
22
| Steady White Front|
–
| –| –| –| –| –| –| –| –| –
23
| Steady White Rear|
–
| –| –| –| –| –| –| –| –| –
24
| Title 13 Steady Single Front Red|
–
| –| –| –| –| –| –| –| –| –
25
| Title 13 Steady Single Front Blue|
–
| –| –| –| –| –| –| –| –| –
26
| Title 13 Steady Single Front Red and Blue|
–
| –| –| –| –| –| –| –| –| –
27
| 4-LED, Left, 2000 with 250 off.|
–
| –| –| –| –| –| –| –| –| –
28
| 4-LED, Left Solid, 2000 with 250 off.|
–
| –| –| –| –| –| –| –| –| –
29
| 4-LED, LeftFillAndChase, 2000 with 250 off.|
–
| –| –| –| –| –| –| –| –| –
30
| 4-LED, Right, 2000 with 250 off. |
–
| –| –| –| –| –| –| –| –| –
31
| 4-LED, Right Solid, 2000 with 250 off.|
–
| –| –| –| –| –| –| –| –| –
32
| 4-LED, RightFillAndChase, 2000 with 250 off.|
–
| –| –| –| –| –| –| –| –| –
33
| 4-LED, Center Out, 1000 with 250 off, 2 repeats.|
–
| –| –| –| –| –| –| –| –| –
34
| 4-LED, Center Out Solid, 1000 with 250 off, 2 repeats.|
–
| –| –| –| –| –| –| –| –| –
35
| 4-LED, CenterFillAndChase, 1000 with 250 off, 2 repeats.|
–
| –| –| –| –| –| –| –| –| –
36
| 4-LED, Quad Flash, 1000 with 83 on and 42 off, 2 sets of 4 repeats.|
–
| –| –| –| –| –| –| –| –| –
37
| 4-LED, Wig Wag, 500 with 250 on and 250 off, 4 repeats.|
–
| –| –| –| –| –| –| –| –| –
38
| 4-LED, Alternating, 500 with 250 on and 250 off, 4 repeats.|
–
| –| –| –| –| –| –| –| –| –
39
| Reg 65 Single 120 FPM, 2.05 Hz|
C1
| –| C1| –| C1| –| C1| –| C2| –
40
| Reg 65 Double 120 FPM, 2.05 Hz|
C1
| –| C1| –| C1| –| C1| –| C2| –
41
| Reg 65 Triple 120 FPM, 2.05 Hz|
C1
| –| C1| –| C1| –| C1| –| C2| –
42
| Reg 65 Quad 120 FPM, 2.05 Hz|
C1
| –| C1| –| C1| –| C1| –| C2| –
43
| Reg 65 Burst 120 FPM, 2.05 Hz|
C1
| –| C1| –| C1| –| C1| –| C2| –
44
| Reg 65 Single S S 120 FPM, 2.05 Hz|
C1
| –| C1| –| C1| –| C1| –| C2| –
45
| Reg 65 Double S S 120 FPM, 2.05 Hz|
C1
| –| C1| –| C1| –| C1| –| C2| –
46
| Reg 65 Triple S S 120 FPM, 2.05 Hz|
C1
| –| C1| –| C1| –| C1| –| C2| –
47
| Reg 65 Quad S S 120 FPM, 2.05 Hz|
C1
| –| C1| –| C1| –| C1| –| C2| –
48
| Reg 65 Burst S S 120 FPM, 2.05 Hz|
C1
| –| C1| –| C1| –| C1| –| C2| –
49
| Reg 65 Single S S 120 FPM Center Pulse, 2.05 Hz|
C1
| –| C1| –| C1| –| C1| –| C2| –
50
| Reg 65 Double S S 120 FPM Center Pulse, 2.05 Hz|
C1
| –| C1| –| C1| –| C1| –| C2| –
51
| Reg 65 Triple S S 120 FPM Center Pulse, 2.05 Hz|
C1
| –| C1| –| C1| –| C1| –| C2| –
52
| Reg 65 Quad S S 120 FPM Center Pulse, 2.05 Hz|
C1
| –| C1| –| C1| –| C1| –| C2| –
53
| Reg 65 Burst S S 120 FPM Center Pulse, 2.05 Hz|
C1
| –| C1| –| C1| –| C1| –| C2| –
54
| Cycle All|
–
| –| –| –| –| –| –| –| –| –
55
| Steady PWM 50|
–
| –| –| –| –| –| –| –| –|
–
|
CA T13
---|---
Number| Flash Pattern| EZ1203A
EZ1206AX| EZ1203B
EZ1206BX| EZ1203R
EZ1206RX
D
| D| D
1
| Double 75 FPM – DEFFAULT PATTERN FOR LEVEL 1|
–
| CLASS B| CLASS B
2
| Title 13 Quad 65 FPM – DEFFAULT PATTERN FOR LEVEL 2|
CLASS E
| CLASS B| CLASS B
3
| Title 13 Double 65 FPM|
CLASS E
| CLASS B| CLASS B
4
| Quint Hold 75 FPM – DEFFAULT PATTERN FOR LEVEL 3|
–
| CLASS B| CLASS B
5
| Pulse 8 Burst 75 FPM|
–
| –| –
6
| Quad Alternate S S 150 FPM|
–
| –| –
7
| Quad Cross Alternate 150 FPM|
–
| –| –
8
| Double Alternate S S 150 FPM|
–
| –| –
9
| Double Cross Alternate 150 FPM|
–
| –| –
10
| Quint Hold Alternate S S 150 FPM|
–
| –| –
11
| Quint Hold Cross Alternate 150 FPM|
–
| –| –
12
| Quad Alternate S S 150 FPM Center Pulse|
–
| –| –
13
| Double Alternate S S 150 FPM Center Pulse|
–
| –| –
14
| Quint Hold Alternate S S 150 FPM Center Pulse|
–
| –| –
15
| Fast Rotate|
–
| –| –
16
| Wave Rotate|
–
| –| –
17
| Rotate Quad|
–
| –| –
18
| Fast Quad|
–
| –| –
19
| Airport Flash 75 FPM|
–
| –| –
20
| Steady White Left|
–
| –| –
21
| Steady White Right|
–
| –| –
22
| Steady White Front|
–
| –| –
23
| Steady White Rear|
–
| –| –
24
| Title 13 Steady Single Front Red|
–
| –| CLASS B
25
| Title 13 Steady Single Front Blue|
–
| CLASS B| –
26
| Title 13 Steady Single Front Red and Blue|
–
| –| CLASS B
27
| 4-LED, Left, 2000 with 250 off.|
–
| –| –
28
| 4-LED, Left Solid, 2000 with 250 off.|
–
| –| –
29
| 4-LED, LeftFillAndChase, 2000 with 250 off.|
–
| –| –
30
| 4-LED, Right, 2000 with 250 off. |
–
| –| –
31
| 4-LED, Right Solid, 2000 with 250 off.|
–
| –| –
32
| 4-LED, RightFillAndChase, 2000 with 250 off.|
–
| –| –
33
| 4-LED, Center Out, 1000 with 250 off, 2 repeats.|
–
| –| –
34
| 4-LED, Center Out Solid, 1000 with 250 off, 2 repeats.|
–
| –| –
35
| 4-LED, CenterFillAndChase, 1000 with 250 off, 2 repeats.|
–
| –| –
36
| 4-LED, Quad Flash, 1000 with 83 on and 42 off, 2 sets of 4 repeats.|
–
| –| –
37
| 4-LED, Wig Wag, 500 with 250 on and 250 off, 4 repeats.|
–
| –| –
38
| 4-LED, Alternating, 500 with 250 on and 250 off, 4 repeats.|
–
| –| –
39
| Reg 65 Single 120 FPM, 2.05 Hz|
–
| –| –
40
| Reg 65 Double 120 FPM, 2.05 Hz|
–
| –| –
41
| Reg 65 Triple 120 FPM, 2.05 Hz|
–
| –| –
42
| Reg 65 Quad 120 FPM, 2.05 Hz|
–
| –| –
43
| Reg 65 Burst 120 FPM, 2.05 Hz|
–
| –| –
44
| Reg 65 Single S S 120 FPM, 2.05 Hz|
–
| –| –
45
| Reg 65 Double S S 120 FPM, 2.05 Hz|
–
| –| –
46
| Reg 65 Triple S S 120 FPM, 2.05 Hz|
–
| –| –
47
| Reg 65 Quad S S 120 FPM, 2.05 Hz|
–
| –| –
48
| Reg 65 Burst S S 120 FPM, 2.05 Hz|
–
| –| –
49
| Reg 65 Single S S 120 FPM Center Pulse, 2.05 Hz|
–
| –| –
50
| Reg 65 Double S S 120 FPM Center Pulse, 2.05 Hz|
–
| –| –
51
| Reg 65 Triple S S 120 FPM Center Pulse, 2.05 Hz|
–
| –| –
52
| Reg 65 Quad S S 120 FPM Center Pulse, 2.05 Hz|
–
| –| –
53
| Reg 65 Burst S S 120 FPM Center Pulse, 2.05 Hz|
–
| –| –
54
| Cycle All|
–
| –| –
55
| Steady PWM 50|
–
| –|
–
| ECE R65
---|---
Number| Flash Pattern| EZ1203A
EZ1206AX| EZ1203B
EZ1206BX| EZ1203R
EZ1206RX
D
| D| D
1
| Double 75 FPM – DEFFAULT PATTERN FOR LEVEL 1|
–
| –| –
2
| Title 13 Quad 65 FPM – DEFFAULT PATTERN FOR LEVEL 2|
–
| –| –
3
| Title 13 Double 65 FPM|
–
| –| –
4
| Quint Hold 75 FPM – DEFFAULT PATTERN FOR LEVEL 3|
–
| –| –
5
| Pulse 8 Burst 75 FPM|
–
| –| –
6
| Quad Alternate S S 150 FPM|
–
| –| –
7
| Quad Cross Alternate 150 FPM|
–
| –| –
8
| Double Alternate S S 150 FPM|
–
| –| –
9
| Double Cross Alternate 150 FPM|
–
| –| –
10
| Quint Hold Alternate S S 150 FPM|
–
| –| –
11
| Quint Hold Cross Alternate 150 FPM|
–
| –| –
12
| Quad Alternate S S 150 FPM Center Pulse|
–
| –| –
13
| Double Alternate S S 150 FPM Center Pulse|
–
| –| –
14
| Quint Hold Alternate S S 150 FPM Center Pulse|
–
| –| –
15
| Fast Rotate|
–
| –| –
16
| Wave Rotate|
–
| –| –
17
| Rotate Quad|
–
| –| –
18
| Fast Quad|
–
| –| –
19
| Airport Flash 75 FPM|
–
| –| –
20
| Steady White Left|
–
| –| –
21
| Steady White Right|
–
| –| –
22
| Steady White Front|
–
| –| –
23
| Steady White Rear|
–
| –| –
24
| Title 13 Steady Single Front Red|
–
| –| –
25
| Title 13 Steady Single Front Blue|
–
| –| –
26
| Title 13 Steady Single Front Red and Blue|
–
| –| –
27
| 4-LED, Left, 2000 with 250 off.|
–
| –| –
28
| 4-LED, Left Solid, 2000 with 250 off.|
–
| –| –
29
| 4-LED, LeftFillAndChase, 2000 with 250 off.|
–
| –| –
30
| 4-LED, Right, 2000 with 250 off. |
–
| –| –
31
| 4-LED, Right Solid, 2000 with 250 off.|
–
| –| –
32
| 4-LED, RightFillAndChase, 2000 with 250 off.|
–
| –| –
33
| 4-LED, Center Out, 1000 with 250 off, 2 repeats.|
–
| –| –
34
| 4-LED, Center Out Solid, 1000 with 250 off, 2 repeats.|
–
| –| –
35
| 4-LED, CenterFillAndChase, 1000 with 250 off, 2 repeats.|
–
| –| –
36
| 4-LED, Quad Flash, 1000 with 83 on and 42 off, 2 sets of 4 repeats.|
–
| –| –
37
| 4-LED, Wig Wag, 500 with 250 on and 250 off, 4 repeats.|
–
| –| –
38
| 4-LED, Alternating, 500 with 250 on and 250 off, 4 repeats.|
–
| –| –
39
| Reg 65 Single 120 FPM, 2.05 Hz|
CLASS 1
| CLASS 1| CLASS 1
40
| Reg 65 Double 120 FPM, 2.05 Hz|
CLASS 1
| CLASS 1| CLASS 1
41
| Reg 65 Triple 120 FPM, 2.05 Hz|
CLASS 1
| CLASS 1| CLASS 1
42
| Reg 65 Quad 120 FPM, 2.05 Hz|
CLASS 1
| CLASS 1| CLASS 1
43
| Reg 65 Burst 120 FPM, 2.05 Hz|
CLASS 1
| CLASS 1| CLASS 1
44
| Reg 65 Single S S 120 FPM, 2.05 Hz|
CLASS 1
| CLASS 1| CLASS 1
45
| Reg 65 Double S S 120 FPM, 2.05 Hz|
CLASS 1
| CLASS 1| CLASS 1
46
| Reg 65 Triple S S 120 FPM, 2.05 Hz|
CLASS 1
| CLASS 1| CLASS 1
47
| Reg 65 Quad S S 120 FPM, 2.05 Hz|
CLASS 1
| CLASS 1| CLASS 1
48
| Reg 65 Burst S S 120 FPM, 2.05 Hz|
CLASS 1
| CLASS 1| CLASS 1
49
| Reg 65 Single S S 120 FPM Center Pulse, 2.05 Hz|
–
| –| –
50
| Reg 65 Double S S 120 FPM Center Pulse, 2.05 Hz|
–
| –| –
51
| Reg 65 Triple S S 120 FPM Center Pulse, 2.05 Hz|
–
| –| –
52
| Reg 65 Quad S S 120 FPM Center Pulse, 2.05 Hz|
–
| –| –
53
| Reg 65 Burst S S 120 FPM Center Pulse, 2.05 Hz|
–
| –| –
54
| Cycle All|
–
| –| –
55
| Steady PWM 50|
–
| –|
–
Safety Director™ Flash Patterns
Number
| Name
---|---
1
| Left Cut
2
| Right Cut
3
| Left and Right Cut
4
| Front Cut
5
| Front and Left Cut
6
| Front and Right Cut
7
| Front and Left and Right Cut
8
| Rear Cut
9
| Rear and Left Cut
10
| Rear and Right Cut
11
| Rear and Left and Right Cut
12
| Front and Rear Cut
NOTE:
- All SAE J845 compliant patterns have at least 180° of coverage with the minimum configuration of two corner modules, one forward facing and one rear facing module.
Replacement Parts/Accessories
Description
|
Part No.
---|---
Lenses|
Replacement 24″ End Lens – Clear|
ER0003
Replacement 6″ Mid Lens – Clear|
ER0004
|
Driver PCA|
12 Channel Driver Board|
20 Channel Driver Board|
|
Led Modules|
3-LED Ice Optic Module – Amber|
EZ1203A
3-LED Ice Optic Module – Blue|
EZ1203B
3-LED Ice Optic Module – Green|
EZ1203G
3-LED Ice Optic Module – Red|
EZ1203R
3- LED Ice Optic Module – White|
EZ1203W
4-LED Worklight / Alley Light Module Pair – White|
EZ0003
6-LED Flare Optic Stop / Turn / Tail (STT) Module Pair – Red|
EZ1205
6-LED Ice Optic Dual Color Module – Amber / Blue|
EZ1206AB
6-LED Ice Optic Dual Color Module – Amber / Red|
EZ1206AR
6-LED Ice Optic Dual Color Module – Amber / White|
EZ1206AW
6-LED Ice Optic Dual Color Module – Blue / White|
EZ1206BW
6-LED Ice Optic Dual Color Module – Red / Blue|
EZ1206RB
6-LED Ice Optic Dual Color Module – Red / White|
EZ1206RW
|
Cables|
15′ Extension Cable – For use with Standard Wiring|
EZ0008
23′ Extension Cable – For use with Standard Wiring|
EZ0008-23
48′ Extension Cable – For use with Standard Wiring|
EZ0008-48
15′ Extension Cable – For use with Advanced Controller EZ1202|
EZ1210
48′ Extension Cable – For use with Advanced Controller EZ1202|
EZ1413-48
15′ Power Cable|
ER0020
6″ Discrete Wiring Harness (Pigtail) – For use with Standard Wiring|
ER0021
|
Control Options|
Advanced Controller|
EZ1202
Serial Interface Box (SIB)|
EZMATSIB
Remote Rocker Max Pak™, 6 button controller|
450R-L6
6-Rocker Switch Panel|
A9000
Single Illuminated Rocker Switch|
A9891
Single Switch Panel – For use with A9891 Switch|
A9893
Single Illuminate Rocker Switch|
A9901
End Switch Panel Section – For use with A9901 Switch|
A9902
Center Switch Panel Section – For use with A9901 Switch & End Panel Sections A9902|
A9903
Switch Panel Mounting Kit – For use with A9901 Switch & Panel Sections A9902 & A9903|
A9904
On / Off Switch Panel with Pattern Select|
A9905SW
|
Mounting Kits|
Permanent mounting feet and hardware – Black|
ER0002
Permanent mounting feet and hardware – White|
ER0001
Headache rack mounting kit|
A1032RMK
NOTE: For list of vehicle specific brackets, please contact a Code 3 representative or our latest catelog.
Troubleshooting
All lightbars are thoroughly tested prior to shipment. However, should you encounter a problem during installation or during the life of the product, follow the guide below for troubleshooting and repair information. If the problem cannot be rectified using the solutions given below, additional information may be obtained from the manufacturer – contact details are at the end of this document.
NOTE: Operating the vehicle without the outer lens installed on the product may result in damage that will NOT be covered under warranty.
LIGHTBAR AND CONTROLLER
| PROBLEM | POSSIBLE CAUSE | SOLUTION |
|---|---|---|
| Does not function | Poor power or ground connection | If controller functions |
normally, or if a 12/24V control voltage is present on either the Pattern 1
(brown) or Pattern 2 (orange) wires, then replace the driver board in the
lightbar.
If controller does not function, then check fuse, cables, and connections to
the lightbar and to the controller.
Blown fuse| Check wiring, replace fuse
One or two LED head do not flash, but Pattern 1 or Pattern 2 indicator LED on
control module is on.| Open circuit wiring from control module to LED head|
Connect a known-good LED head to the problem output to ensure the control
module is working correctly. Repair or replace.
Failed LED head| Replace LED head
LED head flashes dimly| Defective head or driver board| Check correct LED head
Incorrect flash patterns| Wrong flash configuration| Re-program the lightbar
flash pattern for either Program 1 or Program 2, or both.
Secondary pattern does not function| Normal operation| Primary function
overrides secondary function – turn off primary function
ALLEY / TAKEDOWN / WORKLIGHTS
| PROBLEM | POSSIBLE CAUSE | SOLUTION |
|---|---|---|
| Light does not function | Defective light | Replace light |
| Defective controller | If indicator LED on controller is lit, then it is either |
the light, or the cable to the light, or the driver board. Otherwise the controller is defective.
STOP/TAIL/TURN
| PROBLEM | POSSIBLE CAUSE | SOLUTION |
|---|---|---|
| Both/all lights do not function | Blown fuse | Check wiring, replace fuse |
| No power | Check to see if vehicle S/T/T lights function properly | |
| Failed S/T/T LED head | Make sure that the S/T/T head is plugged into the S/T/T |
control board and not the driver board. Replace S/T/T LED head and/or its cable.
Manufacturer Limited Warranty Policy:
Manufacturer warrants that on the date of purchase this product will conform to Manufacturer’s specifications for this product (which are available from the Manufacturer upon request). This Limited Warranty extends for Sixty (60) months from the date of purchase.
DAMAGE TO PARTS OR PRODUCTS RESULTING FROM TAMPERING, ACCIDENT, ABUSE, MISUSE, NEGLIGENCE, UNAPPROVED MODIFICATIONS, FIRE OR OTHER HAZARD; IMPROPER INSTALLATION OR OPERATION; OR NOT BEING MAINTAINED IN ACCORDANCE WITH THE MAINTENANCE PROCEDURES SET FORTH IN MANUFACTURER’S INSTALLATION AND OPERATING INSTRUCTIONS VOIDS THIS LIMITED WARRANTY.
Exclusion of Other Warranties:
MANUFACTURER MAKES NO OTHER WARRANTIES, EXPRESS OR IMPLIED. THE IMPLIED WARRANTIES FOR MERCHANTABILITY, QUALITY OR FITNESS FOR A PARTICULAR PURPOSE, OR ARISING FROM A COURSE OF DEALING, USAGE OR TRADE PRACTICE ARE HEREBY EXCLUDED AND SHALL NOT APPLY TO THE PRODUCT AND ARE HEREBY DISCLAIMED, EXCEPT TO THE EXTENT PROHIBITED BY APPLICABLE LAW. ORAL STATEMENTS OR REPRESENTATIONS ABOUT THE PRODUCT DO NOT CONSTITUTE WARRANTIES.
Remedies and Limitation of Liability:
MANUFACTURER’S SOLE LIABILITY AND BUYER’S EXCLUSIVE REMEDY IN CONTRACT, TORT (INCLUDING NEGLIGENCE), OR UNDER ANY OTHER THEORY AGAINST MANUFACTURER REGARDING THE PRODUCT AND ITS USE SHALL BE, AT MANUFACTURER’S DISCRETION, THE REPLACEMENT OR REPAIR OF THE PRODUCT, OR THE REFUND OF THE PURCHASE PRICE PAID BY BUYER FOR NON-CONFORMING PRODUCT. IN NO EVENT SHALL MANUFACTURER’S LIABILITY ARISING OUT OF THIS LIMITED WARRANTY OR ANY OTHER CLAIM RELATED TO THE MANUFACTURER’S PRODUCTS EXCEED THE AMOUNT PAID FOR THE PRODUCT BY BUYER AT THE TIME OF THE ORIGINAL PURCHASE. IN NO EVENT SHALL MANUFACTURER BE LIABLE FOR LOST PROFITS, THE COST OF SUBSTITUTE EQUIPMENT OR LABOR, PROPERTY DAMAGE, OR OTHER SPECIAL, CONSEQUENTIAL, OR INCIDENTAL DAMAGES BASED UPON ANY CLAIM FOR BREACH OF CONTRACT, IMPROPER INSTALLATION, NEGLIGENCE, OR OTHER CLAIM, EVEN IF MANUFACTURER OR A MANUFACTURER’S REPRESENTATIVE HAS BEEN ADVISED OF THE POSSIBILITY OF SUCH DAMAGES. MANUFACTURER SHALL HAVE NO FURTHER OBLIGATION OR LIABILITY WITH RESPECT TO THE PRODUCT OR ITS SALE, OPERATION AND USE, AND MANUFACTURER NEITHER ASSUMES NOR AUTHORIZES THE ASSUMPTION OF ANY OTHER OBLIGATION OR LIABILITY IN CONNECTION WITH SUCH PRODUCT.
This Limited Warranty defines specific legal rights. You may have other legal rights which vary from jurisdiction to jurisdiction. Some jurisdictions do not allow the exclusion or limitation of incidental or consequential damages.
Product Returns:
*If a product must be returned for repair or replacement, please contact our factory to obtain a Return Goods Authorization Number (RGA number) before you ship the product to Code 3®, Inc. Write the RGA number clearly on the package near the mailing label. Be sure you use sufficient packing materials to avoid damage to the product being returned while in transit.**
*Code 3®, Inc. reserves the right to repair or replace at its discretion. Code 3®, Inc. assumes no responsibility or liability for expenses incurred for the removal and /or reinstallation of products requiring service and/or repair.; nor for the packaging, handling, and shipping: nor for the handling of products returned to sender after the service has been rendered.
10986 North Warson Road
St. Louis, MO 63114 USA
314-996-2800
c3_tech_support@code3esg.com
CODE3ESG.com
439 Boundary Road
Truganina Victoria, Australia
+61 (0)3 8336 0680
esgapsales@eccogroup.com
CODE3ESG.com/au/en
Unit 1, Green Park, Coal Road
Seacroft, Leeds, England LS14 1FB
+44 (0)113 2375340
esguk-code3@eccogroup.com
CODE3ESG.co.uk
An ECCO SAFETY GROUP™ Brand
ECCOSAFETYGROUP.com
© 2022 Code 3, Inc. All rights reserved.
920-0909-01 Rev. B
Read User Manual Online (PDF format)
Read User Manual Online (PDF format) >>