ALPINE PXE-640E-EL Sound Track Audio Processing Amplifier Instruction Manual

ALPINE PXE-640E-EL Sound Track Audio Processing Amplifier Instruction Manual

Operating Instructions

Type of precautions

Prohibited| Indicates a prohibited action (must not be performed).
---|---

Prohibited| Indicates that disassembly is prohibited.

Mandatory| ** Indicates a mandatory operation (must be performed).
**| Indicates that it should draw your close attention.

Warning

In case of problems, please stop using the device immediately.
Otherwise, it may result in personal injury or damaged product. Please return the product to the authorized Alpine dealer or nearby Alpine service center for repair.

The product is only suitable for 12V negative-grounded vehicles.
Otherwise, it may lead to an accident like fire, etc.

Please call a professional for wiring and installation
It needs professional expertise and experience to wire and install the product. Please contact the dealer from whom you bought the product to install it for safety.

Please do not disassemble or refit.
Otherwise, it may result in an accident, fire or electric shock.

Small items like bolts or screws should be kept out of the reach of child.
If ingested, it may result in severe damage. Once ingested, please seek medical attention immediately.

Please do not use any function that may distract you during driving.

Any device function that may influence your attention must be used only when the vehicle is stopped completely. To use these functions, make sure to stop your vehicle in a safe area first. Otherwise, it may result in an accident.

During driving, you must maintain the volume at a level such that the noise outside can still be heard.
It is very dangerous not to clearly hear an emergency vehicle alarm and road warning signal (such as a railway crossing) and may result in an accident. Moreover, a too-large volume may damage your hearing

Caution

Product cleaning
Please clean the product regularly with a soft dry cloth.
For any dirt difficult to clean, only water can be used to soak the cloth. Any other solvents may lead to dissolution.

Temperature
Before starting the device, please ensure that the temperature inside the vehicle is between +60°C and – 20°C.

Repair
In case of problems, please do not repair them by yourself. Please return the product to the authorized Alpine dealer or nearby Alpine service center to repair.

System matching
When PXE-640E-EL is used with active division mode to assign signals for speakers, please ensure that the frequency division point of high pitch is above 1500 Hz to avoid damage to high-pitch speakers.

Installation site
The device cannot be installed at the following locations:

• Under direct sunlight and near a hot source.
• With high humidity and near a water source.
• Dusty sites.
• Environments with violent vibration.

Copyright notice

The text mark and logo of Bluetooth® are the registered trademarks held by Bluetooth SIG, Inc. Alpine Electronics has been authorized to use these text marks and logos. Other trademarks and names all belong to their holders.

Tools that may be required (depending on the vehicle)

| | |
Phillips screwdriver| Sleeve wrench| Wrench| Wire cutter
| | |
Wire crimper| Wire stripper| Spectrum analyzer| Oscilloscope
| | |

Accessory list

• USB 2.0 cable
  

• Mounting bracket × 2

• Machine tooth screw × 4

• Self-tapping screw ×2

• Host machine

Diagram of device interfaces

Description of device interfaces and their functions

1, 2| High voltage level input/output and power interface| The high-voltage level input is connected to the power output of the vehicle audio player and the high-voltage level output is connected to the loudspeaker.
---|---|---
3| Input select switch interface| If the switch is put to “ACC,” the device will be started by ACC. If put to “HOST,” the device will be started by the high voltage level input signal FL-/FL+.
4| Power lamp| Power lamp.
5| RCA audio out| One set of RCA audio signal output which can be connected to the external power amplifier.
6| USB 2.0 interface| A USB 2.0 cable can be used to connect the computer and perform tone tuning and setting in detail.

Wire pin arrangement

Description of mobile APP – General User

1| Master volume| Drag and rotate the volume adjustment fader or click “+” and “-” to adjust the master volume. The volume adjusting range is 0~35.
---|---|---
2| Mute button| Mute the master volume
3| Connection indicator| When the Bluetooth icon is red, the mobile phone Bluetooth is not connected; when it is green, the mobile phone Bluetooth is connected.
4| Menu bar| Check device version.
5| Mode switch| Switch between General User mode and Professional User mode (General User is selected by default).
6| Homepage| General User mode only supports quick operations including audio source switch, pre-set sound effects recall and saving, and device version check.

1| Menu bar| You can encrypt data, set shutdown delay, share sound effect, save sound effect, select online effect, select local effect, check device temperature, set EQ gain step, and check version number.
---|---|---
2| Mode switch| Switch between General User mode and Professional User mode. Type in 6-digit password “888888” to enter Professional User mode, which supports professional tuning operation.
3| Interface selection| Profession User mode has 5 pages of different functions of tuning, namely Homepage, EQ, Channel, Delay and Frequency combination.

Description of mobile APP – Homepage

source, the lower the master volume is. The range of attenuation is 0% ~ 100%.
3| Auxiliary audio source| Select auxiliary audio source (High Level, Bluetooth and OFF).
4| Pre-set sound effects| Save or recall multiple pre-set sound effects.

Caution: If the current audio source mode is selected, this mode cannot be superimposed anymore. Otherwise, the auxiliary audio source will be invalid.

Description of mobile APP – EQ

1| Output channel| Slide left and right to select the output channel for EQ adjustment. There are 6 channels to choose from.
---|---|---
2| Parametric EQ, Graphic EQ| Switch between Parametric EQ mode and Graphic EQ mode. Mode switch would lead to loss of all settings.
3| Gain| Pull the fader up and down to adjust the gain. The adjustable range is: -12.0dB ~ +12.0dB.
4| Frequency, Q value, Gain| Adjust the frequency, Q value and gain of the output channel. The gain is adjustable but the frequency and Q value are fixed in the Graphic EQ interface. The frequency, Q value and gain are all adjustable in the Parametric EQ interface.
5| Reset EQ| Reset EQ setting.
6| Restore EQ, Direct EQ| Switch the tuned EQ data to direct state, click it again to restore the EQ data before Direct EQ setting.

Description of mobile APP – Channel

1| Debugging| The debugging modes to choose from include “Copy channel EQ/volume from left to right” or “Copy channel EQ/volume from right to left”.
---|---|---
2| Locking| You can lock the current channel type.
3| Reset channel type| Select “Clear” to set the current channel type as Empty; select “Default” to set the current channel type as Factory setting.
4| Channel gain| Push the fader left and right to adjust the channel volume in the range of -60dB ~ +6dB; click the speaker button to mute.
5| Channel phase| Select the channel phase (normal phase or reverse-phase).
6| Channel type| Select the output channel type in the pop-up window.
7| Divider| Turn on or off the low-pass filter.
8| Filter type| Select filter type (Linkwitz-Riley, Butterworth or Bessel). Caution: If the slope is -6dB/Oct, the type is not settable.
9| Frequency divider slope| Select the divider slope (-6dB/Oct, -12dB/Oct, -18dB/Oct, -24dB/Oct, -30dB/Oct, -36dB/Oct, – 42dB/Oct, or -48dB/Oct).
10| Divider frequency| Select the divider frequency (between 20Hz and 20kHz).

Description of mobile APP – Delay

1| Speaker| Select the speaker of the corresponding channel, click the speaker to mute it, click it again to cancel mute.
---|---|---
2| Delay setting| Select the corresponding speaker, push the fader left and right on the pop-up window to adjust the delay, or click “+” and “-” to adjust the delay.
3| Unit of delay| Units of delay to choose from include ms, cm, and inch. Adjusting range: 0.000 ~ 7.354 milliseconds, 0 ~ 254 centimeters, and 0 ~ 100 inches.
4| Delay group| There are 3 delay groups to choose from for each channel.

Description of mobile APP – Frequency combination

1| Active or passive output| Keep the default setting as “Passive”.Warning: if changed, you will lose the sound mixer setting of this channel.
---|---|---
2| Input channel| Push the fader left and right or press “+” and “-” to adjust the volume of each audio source in the channel to achieve the purpose of sound mixing and frequency mixing.

Caution: It is strongly recommended to set the total volume of a channel to 100 to avoid clipping.

Interface of PC software

• File
• Options
• Encryption
• Temperature
• Master volume
• Homepage
• Delay
• Frequency combination
• Front left full frequency
• Front right full frequency
• Rear left full frequency
• Rear right full frequency
• Left ultralow frequency
• Right ultralow frequency
• EQ gain step size
• Band
• Frequency
• Q value
• Gain
• Direct
• Reset EQ
• Restore EQ
• Channel setting
• Debugging
• Locking
• Reset
• Gain
• Phase
• Normal phase
• High-pass filter
• Type
• Frequency
• Slope
• Empty
• Low-pass filter
• Graphic EQ
• Parametric EQ
• Master audio source selection
• Auxiliary audio source selection
• High level
• Bluetooth
• Master audio source attenuation
• OFF
• Pre-set sound effects
• Online sound effects
• Pre-set 1
• Pre-set 2
• Pre-set 3
• Pre-set 4
• Pre-set 5
• Pre-set 6
• Click the right mouse button to delete pre-set sound effects
• Normal phase
• Delay group
• High level 1
• High level 2
• High level 3
• High level 4
• Bluetooth Left
• Bluetooth Right
• Passive input
• Active input

Description of PC software

delay, switch between English and Chinese, check the version number.
4| Encryption| Enter a 6-digit encryption password to encrypt the tuned sound effect data.
5| EQ gain step size| Step size can be chosen from the range: 0.1dB ~ 0.5dB ~ 1.0dB.
6| Mute button| Mute the master volume
7| Master volume| Push the fader left and right to adjust the master volume in the range of 0 ~ 35.
8| Homepage| Master audio source selection (High Level and Bluetooth), auxiliary audio source selection (High Level, Bluetooth and OFF), master audio source attenuation adjustment, pre-set sound effects recall and saving, and recall of multiple sets of online sound effects are supported.
9| EQ| Enter the EQ interface to go to the professional tuning interface.
10| Delay| Enter the Delay interface, set the delay value, unit of delay and delay group.
11| Frequency combination| Enter the Frequency combination interface, Sound mixing and Frequency mixing setting.
12| Output channel display| Display the output channel curve.
13| EQ curve| Display the current EQ curve status, set the frequency, Q value and gain.
14| Frequency, Q value, Gain| Adjust the frequency, Q value and gain of the output channel. The gain is adjustable but the frequency and Q value are fixed in the Graphic EQ interface. The frequency, Q value and gain are all adjustable in the Parametric EQ interface.
15| Parametric EQ, Graphic EQ| Switch between Parametric EQ mode and Graphic EQ mode. Mode switch would lead to loss of all settings.
16| Low-pass filter| Turn on or off the low-pass filter to cut off high frequency. Select filter type (Linkwitz-Riley, Butterworth or Bessel). Select the divider frequency (between 20Hz and 20kHz).Select the divider slope (-6dB/Oct, -12dB/Oct, -18dB/Oct, -24dB/Oct, -30dB/Oct, – 36dB/Oct, -42dB/Oct, or -48dB/Oct).
17| High-pass filter| Turn on or off the high-pass filter to cut off low frequency. Select filter type (Linkwitz-Riley, Butterworth or Bessel). Select the divider frequency (between 20Hz and 20kHz).Select the divider slope (-6dB/Oct, -12dB/Oct, -18dB/Oct, -24dB/Oct, -30dB/Oct, – 36dB/Oct, -42dB/Oct, or -48dB/Oct).
18| Channel phase| Select the channel phase (normal phase or reverse-phase).
19| Channel gain| Push the fader left and right to adjust the channel gain, that it, to adjust the volume of the output channel; the adjustable range is: -60dB ~ +6dB.
20| Reset channel type| Select “Clear” to set the current channel type as Empty; select “Default” to set the current channel type as Factory setting.
21| Locking| You can lock the current channel type.
22| Debugging| The debugging modes to choose from include “Copy channel EQ/volume from left to right” or “Copy channel EQ/volume from right to left”.
23| Direct EQ, Restore EQ| Switch the tuned EQ data to direct state, click it again to restore the EQ data before Direct EQ setting.
24| Reset EQ| Reset EQ setting.
25| Output channel| There are 6 output channels to choose from. Configure the type of output channel. Click the speaker button to mute.
26| Connection indicator| Connect the PC and the host machine with a USB cable. Open the software to connect the device. Click it again to turn off the connection.

Specification parameters

Functional parameters

~ 20kHz, resolution: 1Hz Q value (slope or gradient): 0.404~28.852Gain: -12.0dB ~ +12.0dB, resolution: 0.1dB ~ 0.5dB ~ 1.0dB
Output signal frequency divider| Each output channel is equipped with independent multi-order high-pass filter, Filter type: Linkwitz-Riley, Bessel, ButterworthFilter cross-over frequency: 20Hz ~ 20kHz, resolution: 1Hz Filter slope (gradient): -6dB/Oct~-48dB/Oct
Output phase| Normal phase or reverse phase (0°/180°)
Output delay| 0.000~7.354ms, 0~254cm, 0~100inch
Pre-set sound effects| Multiple sets of pre-set sound effects data can be saved in the device, call of online sound effects is supported

For iPhone users, please search “Alpine Music” in APP Store to download and install it; for Android users, please scan the QR.

Alpine Music

Read User Manual Online (PDF format)

Read User Manual Online (PDF format)  >>

Download This Manual (PDF format)

Download this manual  >>