ZEBRA VC80 U Mount Bracket Kit Installation Guide
- June 21, 2024
- ZEBRA
Table of Contents
- ZEBRA VC80 U Mount Bracket Kit Installation Guide
- Introduction
- Contents
- Required Tools
- Installation
- Scanner Holder
- Brackets.
- Mounting the U-Mount Bracket to an External Surface
- Top View
- Read More About This Manual & Download PDF:
- Read User Manual Online (PDF format)
- Download This Manual (PDF format)
ZEBRA VC80 U Mount Bracket Kit Installation Guide
Introduction
This installation guide provides instruction on how to install the U-Mount Bracket Kit (P/N: KT-U-MOUNT-VC80-R) for the VC80 and VH10 Vehicle Computers (VC).
Contents
The U-Mount Bracket kit includes:
- Adapter Bracket (quantity: 2)
- U-Mount Bracket (quantity: 1)
- Friction Pad (quantity: 2)
- M6X1X14 screws and washers (quantity: 4 each)
- 5X50 screws (quantity: 4), Flat Washers (quantity: 8), Split Washers (quantity: 4) and Nylok nuts (quantity: 4)
- 25X20 screws and washers (quantity: 2 each)
- Installation guide (quantity: 1)
Required Tools
- Socket and Torque wrench for the M6, M8, and M10
Installation
WARNING ! __ Always disconnect the VC from all battery and
A/C power before servicing components.
NOTE If it is necessary to mount the VC8300 overhead or in any
position that can cause injury to the operator should the unitfall, it is
critical that a secondary tether or other fail-safe device be installed.
To install the U-Mount Bracket:
-
Screw the Adapter Brackets onto the VC using the M6X1X14 screws and
-
Insert the Split Lock Washer on the
-
Insert the Flat Washer on the screw (on top of the Split Lock
-
Torque the screws to 9 Nm (34.5 in-lbs).
-
Mount the U-Mount Bracket in the desired location using the 5X50 Screws, Split Lock Washers, and Flat Washers. Torque the screws to 42 Nm (31 ft-lbs).
-
Place the Friction Pads onto the thread insert on the Adapter
-
Install the subassembly to the U-Mount Bracket using the M8X1.25X20 screws and Adjust the VC to the desired angle. Torque the M8 screws to 27.0 Nm (239.0 in-lbs).
Scanner Holder
The Scanner Holder attachment (P/N: KT-SCANMNT-VC80-R) is not included in the
U-Mount Bracket kit and must be purchased separately.
To attach the Scanner Holder:
- Install the Adapter Bracket on one side of VC using the M6X1X14 screws and washers.
- Install the Adapter Bracket and Scanner Holder subassembly on
the other side of the VC using the M6X1X17 screws included in the Scanner Holder kit. Torque the screws to 3.9 Nm (34.5 in-lbs).
To install the U-mount bracket, follow the installation of the U-bracket shown above for mount system with a threaded hole or through-hole surface accordingly.
- Mount the U-Mount Bracket in the desired location using the M10X1.5X50 screws and Torque the screws to 42 Nm (31 ft-lbs).
- Place the Friction Pads onto the thread insert on the Adapter
Brackets.
- Install the subassembly to the U-Mount Bracket using the M8X1.25X20 screws and Adjust the VC display to the desired angle. Torque the screws to 27.0 Nm (239.0 in-lbs).
NOTE :When mounting the system and unit Over-Head Cage: A customer- supplied mounting plate must withstand the vehicle computer’s weight under vibration and shock. The plate must be made of stainless steel or hardened steel 10mm thick, welded, or firmly secured to the underside of the cage.
Mounting the U-Mount Bracket to an External Surface
The U-Mount Bracket hole dimensions are compatible with following brackets:
- 90500116-R (VC50)
- KT-U-MOUNT-VC70-R (VC70)
WARNING ! The vehicle computer and bracket must be firmly
secured to a surface that can support the vehicle computer’s weight
Always use four 11mm holes with M10 screws to mount the bracket to the
desired location. Using different holes and screws may cause damage and/or
injury.
CAUTION __ Mounts used in industrial or vibration generating
environments may be subjected to fatigue, stress, and/or part wear. A
periodicinspection of the mounting hardware and mounts should be performed to
ensure parts are retightened to the correct torque, free from fractures,
excessive wear, and/or other environmental damage. Any parts found to be
unsafe should be removed and replaced immediately. After inspection or
replacement of parts, readjust the mount as required.
Top View
Zebra Technologies Corporation, Inc. 3 Overlook Point
Lincolnshire, IL 60069, U.S.A. zebra.comZebra and the
stylized Zebra head are trademarks of Zebra Technologies Corporation,
registered in many jurisdictions worldwide. All other trademarks are the
property of their respective owners.
© 2023 Zebra Technologies Corporation and/or its affiliates. All rights
reserved. Patents: ip.zebra.com
Read More About This Manual & Download PDF:
Read User Manual Online (PDF format)
Read User Manual Online (PDF format) >>