SoundPARA Nano Earbuds Manual
- June 16, 2024
- SoundPEATS
Table of Contents
SoundPARA Nano Earbuds Manual
MANUFACTURER
Shenzhen SoundSOUL Information Technology Co.,LTD
Room 1308-1309, Building B, Huihai Square, Chuangye Road,
Longhua District, Shenzhen, China. 51810
support@dudios.com
www.dudios.com
Package Content
Specifications
Bluetooth Version : V5.0
Maximum working range : 33 feet (10m, without obstacle)
Bluetooth Chip set : Realtek 8763BFR
Working Time : 4 hours
Earbuds Charging Time : 2 hours
Charging Case Charging Time : 2 hours
Charging Case Recharge Earbuds : 3-4 times (both earbuds)
Weight : 0.13oz / 3.7g
Dimension (L W H) : 1.1 x 1 x 0.6 inches / 27 x 25 x 16 mm
Button Controls
Wearing
1. Identify the left and right earbuds.
2. Insert the earbuds into your ears and adjust to find best angle with
microphone downwards.
3. Make sure the eartips seal the ear canals.
Getting Started
1. Take out both earbuds from the charging case, the two earbuds will flash
in white at first. Then the le indicator goes out, and right indicator fashes
in red and white with voice prompt “pairing”.
2. Activate the Bluetooth in your device and hit “SoundPARA Nano” on the Bluetooth list, once paired, the right earbud will hear a voice prompt “connected”.
3. The earbuds can remember previously paired devices. They would automati- cally connect to the last device they have paired before aer being taken out from the case. If not, hit “SoundPARA Nano” on the Bluetooth list and re- connected it.
Note
1. If Le earphone doesn’t connect with Right one within 15 seconds when
taking out both from charging case, it will be into standby status. And it
will enter into pairing mode again by putting le earbud in charging case and
waiting for 3s to be taken out again. (The le one will turn o automatically
when in standby mode for 3 minutes)
2. If you want to replace the paired device while it’s connected, you can force the headset to go into pairing mode by long pressing the MFB of right earbud for 6s while the headset is o.
Factory Reset
(Try the following steps if you fail building connection between two earbuds,
or between earbuds and device)1. Clear the pairing record between the earbuds
and all of your devices. 2. Hold and press the MFB of both earbuds for 10
seconds when in charging status, the LED indicator will flash red for 3 times
if resetting successfully.
Charging
SoundPARA Nano Bluetooth earphones are equipped with a compact and lightweight
charging case which is not only a charging dock to charge the earphones, but
also a carrying case. With a built-in rechargeable battery, the charging case
can provide up to 3-4 times full charge for the earphones (both left and right
Charging the headset
The earphones are partially charged at the factory. Please make sure they are
fully charged before first use.1.Put the earphones into corresponding charging
slots, make sure the charging contractors are match.2.The LED indicators on
the earphones turn red to start charging.3.The earphones are fully charged
when LED indicators turn white and turn o aer 1 minute
Charging the case
The charging case can not power o the earbuds or charge them if the case
battery is low or dead. Please charge the case soon.
1.Connect the charging port with any USB charging adapter(The current is no
greater than 1A).
2.Please charge the earphones at least once every 3 months when not in use for
a long time
Warranty
We warrant this device 12 MONTHS from date of the original purchase for
manufacturer defects.
support@dudios.comwww.dudios.com
Please scan the QR code or search the link below for detailed PDF manual
http://dudios.com/index.php/list/index/id/64.htm
FCC Statement
This equipment has been tested and found to comply with the limits for a Class
B digital device, pursuant to Part 15 of the FCC Rules. These limits are
designed to provide reasonable protection against harmful interference in a
residential installation. This equipment generates uses and can radiate radio
frequency energy and, if not installed and used in accordance with the
instructions, may cause harmful interference to radio communications. However,
there is no guarantee that interference will not occur in a particular
installation. If this equipment does cause harmful interference to radio or
television reception, which can be determined by turning the equipment and on,
the user is encouraged to try to correct the interference by one or more of
the following measures:
— Reorient or relocate the receiving antenna.
— Increase the separation between the equipment and receiver.
— Connect the equipment into an outlet on a circuit different from that to
which the receiver is connected.
— Consult the dealer or an experienced radio/TV technician for help.This
device complies with part 15 of the FCC Rules. Operation is subject to the
following two conditions:
(1) This device may not cause harmful interference, and
(2) this device must accept any interference received, including interference that may cause undesired operation.Changes or modifications not expressly approved by the party responsible for compliance could void the user’s authority to operate the equipment.
Read User Manual Online (PDF format)
Read User Manual Online (PDF format) >>