VOLLRATH JT2HC Convertible Conveyor Toasters Instruction Manual
- June 16, 2024
- VOLLRATH
Table of Contents
VOLLRATH JT2HC Convertible Conveyor Toasters
- Thank you for purchasing this Vollrath equipment. Before operating the equipment, read and familiarize yourself with the following operating and safety instructions.
- SAVE THESE INSTRUCTIONS FOR FUTURE REFERENCE. Save the original box and packaging. Use this packaging to ship the equipment if repairs are needed.
SAFETY PRECAUTIONS
- To ensure safe operation, read the following statements and understand their meaning.
- This manual contains safety precautions which are explained below. Please read carefully.
- Warning is used to indicate the presence of a hazard that will or can cause severe personal injury or death.
- Caution is used to indicate the presence of a hazard that will or can cause minor or major personal injury if the caution is ignored.
- NOTICE: Notice is used to note information that is important but not hazard-related.
- To reduce the risk of injury or damage to the equipment
- Plug only into grounded electrical outlets matching the voltage on the rating plate.
- Use this equipment in a flat, level position.
- Unplug the equipment and let it cool before cleaning or moving.
- Equipment remains hot after it is turned off.
- Do not touch during operation.
- Unplug when not in use.
- Keep equipment and power cords away from open flames, electric burners, or excessive heat.
- Do not operate unattended.
- Closely supervise equipment operating in public areas and/or around children.
- Do not operate if equipment has been damaged or is malfunctioning in any way.
FUNCTION AND PURPOSE
This equipment is intended to toast bread, bagels, and sandwiches; and melt cheese. It is intended for use in commercial food service operations only. It is not intended for household, industrial, or laboratory use.
Item No.| Model No.| Voltage| Slices Per **Hour*
(Up to)| Plug**
---|---|---|---|---
CVT4-120300| JT2HC| 120| 300| NEMA 5-15P
CVT4-208550| 208| 550| NEMA 6-20P
CVT4-220550| 220
CVT4-240550| 240
CVT4-208900| JT3HC| 208| 900| NEMA 6-30P
CVT4-220900| 220
CVT4-240900| 240
- Slices per hour are based on maximum conveyor speed. Conveyor speed determines the toasting time and affects the color and texture of the toast.
- Results may vary based on the type of bread, color, and texture preference.
CLEARANCE AND ENVIRONMENT REQUIREMENTS
- Do not place on surfaces or near walls, partitions, or kitchen furniture unless they are made of non-combustible material or clad with non-combustible heat-insulating material.
- Toasters must not be used near or below curtains and other combustible materials.
- Do not place the toaster adjacent to a heat-producing appliance.
SET UP
Install the Collection Pan
- Place the toaster on a hard, flat, stable surface.
- Turn the toaster on its side with the bottom facing you.
- Install the collection pan by placing the back edge of the pan on the lip at the back of the toaster. Line up the hole in the pan with the screw. Tighten the screw to secure the collection pan.
Install the Feed Ramp
- Position the tray so that the opening lines up with the studs.
- Rest tray on studs in the desired location.
FEATURES
- A Power Knob
- Full Power – maximum heat
- Off
- Standby – reduces electrical consumption by 75%.
- B Conveyor Speed Control Knob
- C Unload Tray/Back Panel
- D Heat Shield
- E Feed Ramp
- F Crumb Tray
- G Top Heat Control Knob
- H Bottom Heat Control Knob
- I Collection Pan
- J Reset Button (Reference only. Access is via the front of the toasters.
BEFORE FIRST USE
- Clean the toaster. See “Cleaning.
OPERATION
This toaster ships set up to toast bread. To toast sandwiches, see See “Convert to A Pass through Toaster”.
CAUTION Burn Hazard
- Do not touch the equipment while it is heating or operating. Hot surfaces can burn skin.
- NOTICE: The crumb tray must be installed in the toaster during operation. Failure to install the crumb tray will cause the toaster to overheat.
Adjust the Heat Shield
- Excess space above the product will create heat loss and may reduce performance.
- When the equipment is cool to the touch, use a screwdriver to loosen the screw on the heat shield.
- Grasp the shield and pull it up or down to adjust the opening so the tallest products can pass through. Re-tighten the screw.
Preheat
- Plug the toaster into a grounded electrical outlet that matches the rating on the nameplate found on the side of the toaster.
- NOTICE: Using a voltage other than the nameplate-rated voltage will cause damage to the unit. Incorrect voltage, modification to the power cord, or electrical components can damage the unit and will void the warranty.
- Rotate the power knob(s) to the full power position (I).
- Set the conveyor speed control knob(s) to 7.
- Rotate the top and bottom heat control knobs to high.
- Wait 5 minutes for the toaster to preheat.
Test
Adjust the settings for the product to be toasted.
Tips
Product | Suggestions |
---|---|
Bagels, wheat rye bread, or products with high moisture content. | Use a slower |
conveyor speed.
Buttered or coated, such as pastries| Not recommended.
Frozen| Must be thawed before toasting.
Sandwiches| Use a slower conveyor speed to allow protein ingredients to heat.
Set bottom heat control low.
Test the settings by placing a sample of the food to be toasted onto the feed ramp. Place bagels or buns onto the feed ramp with the cut side facing up.
For One-Sided Toasting
- TOP heat control to the desired setting.
- BOTTOM heat control to the OFF position.
Toast-Bread or Sandwiches
- Adjust the top and bottom heat control settings and conveyor as needed for even toasting. Allow time for the toaster to adjust to new heat settings before placing bread or sandwiches on the conveyor.
- For best performance do not overload the toaster. Wait a few seconds before loading a second row of bread or sandwiches into the toaster.
If an Item Becomes Stuck
- Rotate the power knob to the OFF position (O) and unplug the equipment.
- Let the equipment cool completely. Use tongs to remove the item. Take care to not bump the heating elements above and below the conveyor.
CONVERT TO A PASS-THROUGH TOASTER
- Position the toaster so you have access to the unload tray/back panel.
- Lift the unload tray straight up and tilt outward as shown below.
- Note the tabs on the underside of the back panel. Clip the tabs over the two metal pins under the edges of the panel.
- Drop the unloaded tray into the horizontal position.
CLEANING
- WARNING Electrical Shock Hazard
- Do not spray water or cleaning products. Liquid could contact the electrical components and cause a short circuit or an electrical shock.
- CAUTION Burn Hazard
- Allow equipment to cool before moving or cleaning.
- NOTICE: Do not use abrasive materials, scratching cleansers, or scouring pads to clean the exterior of the equipment. These can damage the finish.
- NOTICE: Heating elements do not need to be cleaned. Crumbs and food debris will burn off. Over time the heating elements may develop a chalky appearance, but this will not impact performance.
Daily Cleaning
- Before turning off the equipment and with the conveyor rotating, watch the conveyor belt for food debris.
- When the food debris reaches the front of the conveyor, rotate the power knob to the OFF position.
- Wait for the fan to stop running. Unplug the equipment.
- Let the equipment cool completely.
- When the equipment is cool, use a brush or scrub pad to remove the food debris.
- To clean the exterior, use a soft cloth dipped in hot soapy water to wipe the exterior and fan air intake under the equipment. If needed, wipe the fan intake area with a degreaser to prevent long-term build-up.
- Empty and clean the crumb tray(s).
PREVENTATIVE MAINTENANCE
Contact an authorized service agent for a professional cleaning of the components.
TROUBLESHOOTING
Problem| Might be Caused By| Course of
Action
---|---|---
The toaster does not heat and the conveyor belt does not move.| The toaster is
not plugged in.| Plug in the toaster.
The power knob setting is incorrect.| Rotate the power knob to the ON (|)
position.
The wall breaker may be tripped.| 1. Inspect for tripped breaker.
2. Reset the breaker.
3. If the breaker was not tripped, inspect the toasting chamber for broken heat tubes.
For broken tubes, contact Vollrath Technical Services.
The reset may be tripped.| Look under the toaster to see if an object is preventing the fan blades from turning.
1. Rotate the heat control knobs to the OFF position.
2. Rotate the power knob to the OFF (O) position.
3. Unplug the toaster.
4. Wait 30 minutes for the toaster to cool.
5. Remove the object.
6. Plug in the toaster.
7. Rotate the power knob to the ON (|) position.
8. Press the reset button. You should hear and feel the button reset. The toaster should start to operate.
9. If the problem persists call Vollrath Technical Services.
Inspect the fan blades to see if they are dirty.
1. Rotate the heat control knobs to the OFF position.
2. Rotate the power knob to the OFF (O) position.
3. Unplug the toaster.
4. Wait 30 minutes for the toaster to cool.
5. Clean the fan blades.
6. Plug in the toaster.
7. Rotate the power knob to the ON (|) position.
8. Press the reset button.
9. If the problem persists call Vollrath Technical Services.
The toaster heats and the conveyor belt does not move.| There may be a problem
with the motor/ speed control or drive chain.| Contact Vollrath Technical
Services.
Top or bottom heater tubes do not heat.| One or more heater tubes may have
burned out.| ****
Contact Vollrath Technical Services.
The heat control switch may be broken.
The toaster repeatedly overheats.| The crumb tray may not be installed.|
Verify the crumb tray is installed.
The fan may be dirty.| Verify the fan blades are clean. See the instructions
above for inspecting and cleaning the fan blades.
There may be a problem with the fan.| Run the toaster for 10 minutes. If the
fan does not run, contact Vollrath Technical Services.
The fan is not running.| There may be a problem with the fan or the fan
switch.| Run the toaster for 10 minutes. If the fan does not run, contact
Vollrath Technical Services.
The toaster is turned off and the fan is running.| Normal operation. The fan
turns on as needed to cool the toaster.| _
SERVICE AND REPAIR
When under warranty, repair is available for this product.
To begin the process:
- Contact Vollrath Technical Services at 1-800-309-2250. Please be ready with the item number, model number, and serial number. You can find this information on the nameplate located on the side or back of the equipment. Also please provide proof of purchase indicating the date the equipment was purchased.
- A technical services representative will help you troubleshoot the problem over the phone.
- If the representative determines the issue requires professional service, he or she will help you locate an authorized service center.
- Contact the authorized service center to make arrangements for the repair. Vollrath will cover the cost to repair and/or replace defective parts within the equipment warranty period.
WARRANTY
WARRANTY STATEMENT FOR THE VOLLRATH CO. L.L.C.
- The Vollrath Company LLC warrants the products it manufactures or distributes against defects in materials and workmanship as specifically described in our full warranty statement.
- In all cases, the warranty runs from the date of the end user’s original purchase date found on the receipt. Any damages from improper use, abuse, modification, or damage resulting from improper packaging during return shipment for warranty repair will not be covered under warranty.
- The warranty does not apply to products purchased for personal, family, or household use, and The Vollrath Company LLC does not offer a written warranty to purchasers for such uses.
- Warrantied Parts : The warranty period is 2 years parts, 1 year labor.
- Heater Tubes: The warranty period is 1 year, including labor. Heater tube glass damage is not covered by this warranty.
- For complete warranty information, product registration, and new product announcements, visit www.vollrath.com.
- www.vollrath.com
- The Vollrath Company, L.L.C.
- 1236 North 18th Street
- Sheboygan, WI 53081-3201 U.S.A. Main Tel: 800.624.2051 or 920.457.4851 Main Fax: 800.752.5620 or 920.459.6573 Customer Service: 800.628.0830 Canada Customer Service: 800.695.8560
- Technical Services techservicereps@vollrathco.com Toasters: 1-800-309-2250
- All Other Products: 800.628.0832
Read User Manual Online (PDF format)
Read User Manual Online (PDF format) >>