Nikon Z TELECONVERTER TC-1.4x Lense User Manual
- June 5, 2024
- Nikon
Table of Contents
NIKKOR
ZTELECONVERTERTC-1.4x
ZTELECONVERTER TC-2.0x
User’s Manual
PrintedinJapan
S80H02(64)
NIKON CORPORA110N
7MMA4664-02 l:J.
| 
---|---
| 
User’s Manual
The TC-1.4x and TC-2.0x Z teleconverters are lens attachments that can be mounted between the main lens and a Nikon Z mount mirrorless camera to increase focal length. The TC-1.4x increases focal length by 1.4x and the TC-2.0x by 2.0x. Before using your new teleconverter, be sure to carefully read both this manual and the documentation provided with the camera and lens.
- The TC-1.4x and TC-2.0x can be used with Z mount lenses that support teleconverters, namely (as of May 2020) the NIKKOR Z 70-200 mm f/2.8VR S.
- Update the firmware for both camera and lens to the latest versions. The latest firmware can be downloaded from the Nikon Download Center at the URL below. https://downloadcenternikonimglib.com/
- A TC-1.4x Z teleconverter is used in this manual for illustrative purposes.
For Your Safety
To prevent damage to property or injury to yourself or to others, read ‘For
Your Safety” in its entirety before using this product. Keep these safety
instructions where all those who use this product will read them
WARNING: Failure to observe the precautions marked with this icon could
result in death or severe injury.
CAUTION: Failure to observe the precautions marked with this icon could
result in injury or property damage.
WARNING
- Do not disassemble or modify this product. Do not touch internal parts that become exposed as the result of a fall or other accident. Failure to observe these precautions could result in electric shock or another injury.
- Should you notice any abnormalities such as the product producing smoke, heat, or unusual odors, immediately disconnect the camera power source. Continued operation could result in fire, burns or another injury.
- Keep dry. Do not handle with wet hands. Failure to observe these precautions could result in fire or electric shock.
- Do not use this product in the presence of flammable dust or gas such as propane, gasoline or aerosols. Failure to observe this precaution could result In an explosion or fire.
- Do not directly view the sun or other bright light sources through the lens. Failure to observe this precaution could result in visual impairment.
- Keep this product out of reach of children. failure to observe this precaution could result in injury or product malfunction. In addition, note that small parts constitute a choking hazard. Should a chiki swallow any part of this product seek immediate medical attention.
CAUTION
- Do not leave the lens pointed at the sun or other strong light sources. Light focused by the lens could cause fire or damage to the product’s internal parts. When shooting backlit subjects, keep the sun well out of the frame. Sunlight focused into the camera when the sun is close to the frame could cause fire.
- Do not leave the product where it will be exposed to extremely high temperatures, for an extended period such as in an enclosed automobile or in direct sunlight. Failure to observe this precaution could result in fire or product malfunction.
- Do not transport cameras or lenses with tripods or similar accessories attached. Failure to observe this precaution could result in injury or product malfunction.
Notices for Customers In the U.S.A.
This device complies with part 15 of the FCC Rules?
Operation is subject to the following two conditions: (1) this device may not
cause harmful interference, and (2) this device must accept any interference
received, including interference that may cause undesired operation.
Federal Communications Commission (FCC) Radio Frequency Interference
Statement
This equipment has been tested and found to comply with the limits for a Class
B digital device, pursuant to Part 15 of the FCC rules. These limits are
designed to provide reasonable protection against harmful interference in a
residential installation. This equipment generates, uses, and can radiate
radio frequency energy and, if not installed and used in accordance with the
instructions, may cause harmful interference to radio communications. However,
there is no guarantee that interference will not occur in a particular
install-lation. If this equipment does cause harmful interference to radio or
television reception, which can be determined by turning the equipment off and
on, the user is encouraged to try to correct the interference by one or more
of the following measures:
- Reorient or relocate the receiving antenna.
- Increase the separation between the equipment and receiver.
- Connect the equipment into an outlet on a circuit different from that to which the receiver is connected.
- Consult the dealer or an experienced radio/television technician for help.
CAUTIONS
Modifications
The FCC requires the user to be notified that any changes or modifications
made to this device that are not expressly approved by Nikon Corporation may
void the user’s authority to operate the equipment. Nikon Inc., 1300 Walt
Whitman Road, Melville, New York 11747-3064, U.S.A. Tel.:
631-547-4200
Notice for Customers in Canada
CAN ICES-313 / NMB 3 B
About Your Teleconverter
Parts of the Teleconverter (Figure 1)
A Lens Side
-
Teleconverter cap (front cap)
-
Front lens element
-
Rubber protector
-
Lens signal contacts
-
Lens mount (front)
-
Lens mounting mark
-
Lens release
B Camera Side -
Camera mounting mark
-
Rubber lens-mount gasket CID Lens mount (rear)
-
CPU contacts
-
Rear lens element
-
Lens cap (rear cap)
‘Attaching and Removing the Teleconverter
Attaching and Removing the Teleconverter: Cautions
-
Your teleconverter is for use with compatible Z MOant lenses only. – Do not attempt to attach incompatible lenses, teleconverters Ice F mount lenses, FTZ mount adapt-ers, or other incompatible accessories, as this could damage the teleconverter, lens, or accessory. – Teleconverters cannot be attached to each other.
-
Attach the lens to the teleconverter before attaching the teleconverter to the camera. Do not attempt to attach the teleconverter without first attaching a lens.
-
The lens mount on the front face of the teleconverter extends further than the mount base. Elements inside the camera that come into contact with the lens mount could be damaged
-
Before attaching or removing the teleconverter, turn the camera off and move to a location out of direct sunlight.
Attachment (Figure 2)
-
Attach the teleconverter to the lens.
• Align the lens mounting mark on the teleconverter with the lens mounting mark on the lens (a -0 and rotate the teleconverter in the direction shown until it clicks into place (a -0).
• Be careful not to press the teleconverter lens release while attaching the teleconverter. -
Attach the assembly to the camera.
• Align the camera mounting mark on the teleconverter with the lens mounting mark on the camera (b-e and rotate the teleconverter in the direction shown until it clicks into place (1)-0.
• Be careful not to press the camera lens release button while attaching the teleconverter.
Removal (Figure 3)
-
Remove the assembly from the camera.
• Hold the camera lens release button (a – 0) while rotating the teleconverter in the direction shown (a -0). The teleconverter can be removed when the camera mount-ing mark on the teleconverter is aligned with the lens mounting mark on the camera. -
Remove the teleconverter from the lens.
• Hold the teleconverter lens release (b -0) while rotating the teleconverter in the direction shown (b -0). The teleconverter can be removed when the lens mount-ing mark on the teleconverter is aligned with the lens mounting mark on the lens.
Lens Speed
Mounting lenses on a teleconverter reduces their speed (effective aperture, or
“brightness): by 1 stop in the case of the TC-1.4x and by 2 stops in the case
of the TC-2.0x.
Precautions for Use
- Keep the CPU contacts dean.
- Should the rubber lens-mount gasket be damaged, cease use immediately and take the teleconverter to a Nikon-authorized service center for repair.
- Replace the teleconverter cap and lens cap when the teleconverter is not in use.
- Do not leave the teleconverter in humid locations or in locations in which it may be exposed to moisture. Rusting of the internal mechanism can cause irreparable damage.
- Do not leave the teleconverter next to open flames or in other extremely hot locations. Extreme heat could damage or warp the reinforced plastic exterior.
- Rapid changes in temperature may cause damaging condensation inside and outside the teleconverter. Before taking the teleconverter from a warm to a cold environment or vice versa, place it in a bag or plastic case to slow the change in temperature.
- We recommend that you place the teleconverter in its case to protect it from scratches during transport
Product Care
- Removing dust is normally sufficient to clean glass lens elements.
- The fluorine-coated front and rear lens elements can be cleaned as described below. – Smudges, fingerprints, and other oily stains can be removed using a soft, clean cotton cloth or lens cleaning tissue; clean from the center outwards using a circular motion. – To remove stubborn stains, wipe gently using a soft cloth lightly dampened with a small amount of distilled water, ethanol, or lens cleaner. – Any drop-shaped marks left from this process on the water- and the oil-repellent surface can subsequently be removed with a dry cloth.
- Never use organic solvents such as paint thinner or benzene to clean any part of the teleconverter.
- Do not store with naphtha or camphor moth balls or in direct sunlight. If the teleconverter will not be used for an extended period, store it in a cool, dry local PGC Y?-P-rf. vffili,r-P-9!-Ck!39d rust.
Accessories
Supplied Accessories
- BF-N2 leleconver ter Cap (horn cap)
- CL-C4 Lens Case
- LT-NI Lens Cap (rear cap)
Using the Lense Case
- The case is Intended to protect the teleconverter from scratches, not from falls or other physical shocks.
- The case Is not vster resistant
- The material used In the case may lade, bleed, stretch, shrink, or change color when rubbed or wet
- Remove dust with a soft brush.
- Water and stains can be removed from the surface with a soft, dry cloth. Do not use alcohol, benzene, thinner, or other volatile chemicals.
- Do not store In locations exposed to direct sunlight or high temperatures or humidity.
- Do not use the case to clean the monitor or lens elements
- Be careful that the teleconverter does not fall from the case during transport Material: Polyester
Specifications
Z TELECONVERTER TC-1.4x
Lens construction| 6 elements in 4 groups (including 1 aspherical I element
and fluorine-coated front and rear elements)
---|---
Mount| •Front: Nikon Z mount (exclusively for lenses that support
teleconverters)
•Rear. Nikon Z mount
Dimensions| Approx. 72 mm/2.9 in. (maximum diameter) x 18.5 mm/0.8 in.
(distance from camera lens mount flange); overall length 37 mm/1.5 in.
Weight| Approx. 220 g (7.8oz)
With main lens
| •Focal length: 121x that of the main lens
•Minimum focus distance: Same as the main lens
•Reproduction ratio: 1.4x that of the main lens
•Depth of field 71.4x that of the main lens
Nikon reserves the right to change the appearance, specifications, and
performance of this product at any time and without prior notice.
I Z TELECONVERTER TC-2.0x
lens construction —| 8 elements in 5 groups (including 1 aspherical element
and fluorine-coated front and rear elements)
---|---
Mount| •Front: Nikon Z mount (exclusively for lenses that support
teleconverters)
•Rear. Nikon Z mount
Dimensions| Approx. 72 mm/2.9 in. (maximum diameter) x 32.5 mm/l.3 in.
(distance from camera lens mount flange); overall length 505 mm/2 in.
Weight| Approx. 2709 (9.6oz)
With main lens
| •Focal length: 2x that of the main lens
•Minimum focus distance: Same as the main lens
•Reproduction ratio 2x that of the main lens
•Depth of field. v. x that of the main lens
Nikon reserves the nght to change the appearance, specifications, and
performance of this product at any time and without prior notice.
Retain this International Warranty with proof of purchase (bill of sale) for
your records Nikon Corp.
LENS ONE YEAR WORLDWIDE LIMITED WARRANTY
(Excluding the Continental United States, Alaska, Hawaii, Puerto Rico, and
U.S. Virgin Islands)
Welcome to the worldwide family of Nikon owners.
Your Nikon equipment has been manufactured to the highest quality standards by
NIKON CORPORATION, Tokyo, Japan. This limited warranty entitles the original
consumer purchaser to international warranty protection in accordance with
these terms and conditions. It affords the original consumer purchaser
warranty protection outside the Continental United States, Alaska, Hawaii,
Puerto Rico and the U.S. Virgin Islands. Such warranty coverage is
supplemental to and not in lieu of the United States Nikon Inc. Lens One Year
USA Limited Warranty which is received by the original consumer purchaser with
the Nikon product. The Nikon product except for batteries is warranted by
NIKON CORPORATION, Tokyo, Japan to be free from defects in materials or
workmanship for a period of one (1)year from the date of purchase. To find an
international Nikon Service Facility see:
http://imaging.nikon.com/products/imaging/worldwide/index.htm. During this
period any one of the international service facilities will service without
charge any parts or assembly of parts found to be defective in materials or
workmanship, subject to the following limitations and exclusions: 1. This
warranty extends to the original consumer purchaser only and is not assignable
or transferable. 2. This warranty shall not extend to any product which has
been subject to misuse, alteration, abuse, negligence, accident or
unauthorized repair or has had its serial number altered or removed.
The above warranty is expressly in lieu of all other warranties expressed
or implied including but not limited to any implied warranty of
merchantability or fitness for a particular purpose, except to the extent
prohibited by applicable law, in which event the duration of any implied
warranty shall be limited to one (1) year from the date of purchase or such
longer period as may be required by applicable law. Under no circumstances
shall Nikon be liable for consequential, indirect, special, direct, exemplary,
punitive or incidental damages arising out of or related to any breach of this
warranty or any other claim regarding this product, including but not limited
to, claims of negligence, strict liability or breach of contract. Some
jurisdictions, such as states or provinces, do not allow (a) limitations on
how long an implied warranty lasts or (b) the exclusion or limitation of
incidental or consequential damages so the above limitations or exclusions may
not apply to you. This warranty gives you specific legal rights and you may
also have other rights which vary from jurisdiction to jurisdiction.
In order to obtain international service, the original consumer purchaser
should return the Nikon product, either in person or addressed to the Warranty
Department of any authorized service facility listed on the above website,
together with proof of purchase and proof of purchase date (bill of sale) and
this warranty. The original consumer purchaser in returning this product must
prepay all shipping and insurance costs to the service facility.
Read User Manual Online (PDF format)
Read User Manual Online (PDF format) >>