ASUS 90GC01N0-MSG050 Universal Gaming Chair Installation Guide

ASUS 90GC01N0-MSG050 Universal Gaming Chair

Product Information

Specifications

• Model: SL301C / SL301CW
• Maximum Load: 2kg
• Adjustable Functions: Headrest, Armrest, Backrest reclining, Chair height, Tilt lock, Seat rockability

Product Usage Instructions

Assembling the Chair:
Follow these steps to assemble your chair:

1. Put on the gloves provided in the package.
2. Place the lumbar cushion against the backrest for support.
3. Insert and push the wheels into the base.

Installing Additional Features:
The chair comes with additional features such as a hanger at the back. Follow these steps to install:

1. Install side covers and tighten the bolts.
2. Mount the hydraulic lift cylinder facing the back of the seat.

Adjusting Functions:
Utilize the adjustable functions of the chair as per your comfort:

• Headrest adjustment
• Armrest adjustment
• Backrest reclining
• Chair height adjustment
• Tilt lock
• Seat rockability adjustment

Frequently Asked Questions (FAQ):

• Q: Can I exceed the maximum load of 2kg on the hanger at the back?
  A: No, please do not hang items over 2kg on the hanger to ensure safety and stability.

• Q: How do I adjust the tilt mechanism of the chair for rocking?
  A: To adjust the seat rockability, locate the tilt mechanism and lock/unlock it as needed for rocking motion.

Safety Notices

• Sit in the center of the chair with your back against the backrest.
• Do not sit on the edge of the chair.
• Do not stand on the chair.
• Do not push down on the reclined backrest when a person is on it.
• Keep your hands and fingers away from the recline mechanism.

WARNING!

1. This chair should only be used in a normal and non-abusive manner. We are not liable for any damages resulting from improper assembly and/or usage.
2. The maximum recommended weight load is 136-kg (299.8 pounds).
3. Never assemble or disassemble your chair in an improper manner.
4. Please keep your chair out of direct sunlight to protect its leather.
5. Please watch your back when the backrest returns back to its original position from a reclined position.
6. To avoid damage to your chair, please do not use excessive force to pull up your headrest.

Package Contents

1. Backrest
2. Seat base
3. Lumbar cushion
4. Wheelbase
5. Wheels
6. Side covers with bolts
7. Control unit
8. Gloves
9. Hydraulic lift cylinder
10. Telescoping cover
11. Hex Key
12. Spare bolt

Note: The illustrations are for reference only and may differ from your actual chair in appearance and features.

Assembling your chair

Put on the gloves before installation.

1. One by one, insert and push the wheels into the base.
2. Insert the hydraulic lift cylinder into the center hole of the base. Remove the red protective cap on top if there was any.
3. Place the telescoping cover on the top of the hydraulic lift cylinder. Armrests normally do not distinguish sides unless labeled otherwise. For models with armrests pre-assembled, please skip this step.
4. Remove the pre-assembled bolts and washers ( 1 & 3 ). Place the 4 large washers ( 1 ) between the armrest mounting bar ( 2 ) and the seat base. Hold the armrest in place, then insert and tighten all 4 bolts ( 3 ). Use the hex key to tighten them all, and repeat on the other side.
5. Use the hex key to remove the pre-assembled bolts and washers from the backrest.
6. Remove the protective foam covers from the brackets of the seat base. Then position the backrest carefully between the brackets. Insert and attach the 4 bolts (2 on each side) you removed in step 5 by hand first. Then use the hex key to tighten them. Start with the two bolts on the top of each side, then the bottom two.
7. Install the side covers and tighten the bolts. (The covers are marked “L” for the left side and “R” for the right on the inside.)
8. Now flip the chair over, facing down. Then remove the 4 premounted bolts from the underside with washers.
9. Repeat the step above to install the control unit, and then place the nut to mount the hydraulic lift cylinder facing the back of the seat (where the backrest is installed).
10. Insert top of the hydraulic lift cylinder into the mounting hole on the control unit, and then turn the chair over in upright position. (Two-person handling is required for your safety).

Installing the Lumbar cushion

The lumbar cushion can be placed according to individual preference to serve as lumbar support.

Other features
Hanger at the back of the chair for hanging your bags, clothes, cups and more.
Maximum load: 2kg
Please do not hang items over 2kg.

Adjustable functions

1. Armrest adjustment
2. Headrest adjustment
3. Backrest reclining
4. Chair height adjustment
5. Tilt lock
6. Seat rockability adjustment

1. Armrest adjustment

2. Height adjustment

3. Forward and backward

4. Rotation adjustment

5. Inward and outward

6. Headrest adjustment
   Height adjustment (7cm)
   Please do not excessively raise your headrest.

7. Pull up the lever and slowly lean back.

8. Chair height adjustment

9. Lock/unlock the tilt mechanism

10. Seat rockability adjustment

Read User Manual Online (PDF format)

Read User Manual Online (PDF format)  >>

Download This Manual (PDF format)

Download this manual  >>